u-boot-2014.10移植

来源:互联网 发布:关于防沉迷网络的建议 编辑:程序博客网 时间:2024/03/28 22:48

最近在学习linux相关知识,下面是CSDN一篇文章,感觉有帮助,保存下来,感谢博主分享,谢谢!

原文博客地址:blog.csdn.net/girlkoo


最近移植了下u-boot-2014.10到TQ335x,如果基于am335x evm进行移植,需要修改的地方并不多。

由于TI的am335x evm开发使用了一个eeprom保存了板载配置信息,用来区分不同板子的型号的,而TQ335x没有这个eeprom,因此,需要修改eeprom相关的部分,使u-boot适应TQ335x开发板。

使用source insight查看代码,很容易发现,所有获取板载配置的部分都是通过读取eeprom获得的,因此,首选修改read_eeprom(board/ti/am335x/board.c)函数,具体的修改如下:

[cpp] view plain copy
  1. static int read_eeprom(struct am335x_baseboard_id *header)  
  2. {  
  3. #if 1  
  4.     strcpy(header->name, "TQ335x");  
  5. #else  
  6.     /* Check if baseboard eeprom is available */  
  7.     if (i2c_probe(CONFIG_SYS_I2C_EEPROM_ADDR)) {  
  8.         puts("Could not probe the EEPROM; something fundamentally "  
  9.             "wrong on the I2C bus.\n");  
  10.         return -ENODEV;  
  11.     }  
  12.   
  13.     /* read the eeprom using i2c */  
  14.     if (i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, 2, (uchar *)header,  
  15.              sizeof(struct am335x_baseboard_id))) {  
  16.         puts("Could not read the EEPROM; something fundamentally"  
  17.             " wrong on the I2C bus.\n");  
  18.         return -EIO;  
  19.     }  
  20.   
  21.     if (header->magic != 0xEE3355AA) {  
  22.         /* 
  23.          * read the eeprom using i2c again, 
  24.          * but use only a 1 byte address 
  25.          */  
  26.         if (i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, 1, (uchar *)header,  
  27.                  sizeof(struct am335x_baseboard_id))) {  
  28.             puts("Could not read the EEPROM; something "  
  29.                 "fundamentally wrong on the I2C bus.\n");  
  30.             return -EIO;  
  31.         }  
  32.   
  33.         if (header->magic != 0xEE3355AA) {  
  34.             printf("Incorrect magic number (0x%x) in EEPROM\n",  
  35.                     header->magic);  
  36.             return -EINVAL;  
  37.         }  
  38.     }  
  39. #endif  
  40.   
  41.     return 0;  
  42. }  
通过上述修改,u-boot不去读取eeprom,而是直接将header的name赋值为"TQ335x",后面可以根据这一配置区分是否为TQ335x开发板。

然后是修改get_dpll_ddr_params(board/ti/am335x/board.c)函数,具体的修改内容如下:

[cpp] view plain copy
  1. const struct dpll_params *get_dpll_ddr_params(void)  
  2. {  
  3.     struct am335x_baseboard_id header;  
  4.   
  5.     enable_i2c0_pin_mux();  
  6.     i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE);  
  7.     if (read_eeprom(&header) < 0)  
  8.         puts("Could not get board ID.\n");  
  9.   
  10.     if (board_is_tq335x(&header) || board_is_evm_sk(&header))  
  11.         return &dpll_ddr_evm_sk;  
  12.     else if (board_is_bone_lt(&header))  
  13.         return &dpll_ddr_bone_black;  
  14.     else if (board_is_evm_15_or_later(&header))  
  15.         return &dpll_ddr_evm_sk;  
  16.     else  
  17.         return &dpll_ddr;  
  18. }  
然后是修改sdram_init(board/ti/am335x/board.c)函数,具体的修改内容如下:
[cpp] view plain copy
  1. void sdram_init(void)  
  2. {  
  3.     __maybe_unused struct am335x_baseboard_id header;  
  4.   
  5.     if (read_eeprom(&header) < 0)  
  6.         puts("Could not get board ID.\n");  
  7.   
  8.     if (board_is_evm_sk(&header)) {  
  9.         /* 
  10.          * EVM SK 1.2A and later use gpio0_7 to enable DDR3. 
  11.          * This is safe enough to do on older revs. 
  12.          */  
  13.         gpio_request(GPIO_DDR_VTT_EN, "ddr_vtt_en");  
  14.         gpio_direction_output(GPIO_DDR_VTT_EN, 1);  
  15.     }  
  16.   
  17.     if (board_is_evm_sk(&header) || board_is_tq335x(&header))  
  18.         config_ddr(303, &ioregs_evmsk, &ddr3_data,  
  19.                &ddr3_cmd_ctrl_data, &ddr3_emif_reg_data, 0);  
  20.     else if (board_is_bone_lt(&header))  
  21.         config_ddr(400, &ioregs_bonelt,  
  22.                &ddr3_beagleblack_data,  
  23.                &ddr3_beagleblack_cmd_ctrl_data,  
  24.                &ddr3_beagleblack_emif_reg_data, 0);  
  25.     else if (board_is_evm_15_or_later(&header))  
  26.         config_ddr(303, &ioregs_evm15, &ddr3_evm_data,  
  27.                &ddr3_evm_cmd_ctrl_data, &ddr3_evm_emif_reg_data, 0);  
  28.     else  
  29.         config_ddr(266, &ioregs, &ddr2_data,  
  30.                &ddr2_cmd_ctrl_data, &ddr2_emif_reg_data, 0);  
  31. }  
然后添加board_is_tq335x函数的具体实现,参考其它类似函数实现即可,由于我们的read_eeprom仅读到了name,其内容是"TQ335x",故可如下实现,在board/ti/am335x/board.h中添加如下内容:
[cpp] view plain copy
  1. static inline int board_is_tq335x(struct am335x_baseboard_id *header)  
  2. {  
  3.     return !strncmp(header->name, "TQ335x", HDR_NAME_LEN);  
  4. }  
最后是修改enable_board_pin_mux(board/ti/am335x/mux.c)函数,具体的修改内容如下:
[cpp] view plain copy
  1. void enable_board_pin_mux(struct am335x_baseboard_id *header)  
  2. {  
  3.     /* Do board-specific muxes. */  
  4.     if (board_is_bone(header) || board_is_tq335x(header)) {  
  5.         /* Beaglebone pinmux */  
  6.         configure_module_pin_mux(i2c1_pin_mux);  
  7.         configure_module_pin_mux(mii1_pin_mux);  
  8.         configure_module_pin_mux(mmc0_pin_mux);  
  9. #if defined(CONFIG_NAND)  
  10.         configure_module_pin_mux(nand_pin_mux);  
  11. #elif defined(CONFIG_NOR)  
  12.         configure_module_pin_mux(bone_norcape_pin_mux);  
  13. #else  
  14.         configure_module_pin_mux(mmc1_pin_mux);  
  15. #endif  
  16.     } else if (board_is_gp_evm(header)) {  
  17.         /* General Purpose EVM */  
  18.         unsigned short profile = detect_daughter_board_profile();  
  19.         configure_module_pin_mux(rgmii1_pin_mux);  
  20.         configure_module_pin_mux(mmc0_pin_mux);  
  21.         /* In profile #2 i2c1 and spi0 conflict. */  
  22.         if (profile & ~PROFILE_2)  
  23.             configure_module_pin_mux(i2c1_pin_mux);  
  24.         /* Profiles 2 & 3 don't have NAND */  
  25. #ifdef CONFIG_NAND  
  26.         if (profile & ~(PROFILE_2 | PROFILE_3))  
  27.             configure_module_pin_mux(nand_pin_mux);  
  28. #endif  
  29.         else if (profile == PROFILE_2) {  
  30.             configure_module_pin_mux(mmc1_pin_mux);  
  31.             configure_module_pin_mux(spi0_pin_mux);  
  32.         }  
  33.     } else if (board_is_idk(header)) {  
  34.         /* Industrial Motor Control (IDK) */  
  35.         configure_module_pin_mux(mii1_pin_mux);  
  36.         configure_module_pin_mux(mmc0_no_cd_pin_mux);  
  37.     } else if (board_is_evm_sk(header)) {  
  38.         /* Starter Kit EVM */  
  39.         configure_module_pin_mux(i2c1_pin_mux);  
  40.         configure_module_pin_mux(gpio0_7_pin_mux);  
  41.         configure_module_pin_mux(rgmii1_pin_mux);  
  42.         configure_module_pin_mux(mmc0_pin_mux_sk_evm);  
  43.     } else if (board_is_bone_lt(header)) {  
  44.         /* Beaglebone LT pinmux */  
  45.         configure_module_pin_mux(i2c1_pin_mux);  
  46.         configure_module_pin_mux(mii1_pin_mux);  
  47.         configure_module_pin_mux(mmc0_pin_mux);  
  48. #if defined(CONFIG_NAND)  
  49.         configure_module_pin_mux(nand_pin_mux);  
  50. #elif defined(CONFIG_NOR)  
  51.         configure_module_pin_mux(bone_norcape_pin_mux);  
  52. #else  
  53.         configure_module_pin_mux(mmc1_pin_mux);  
  54. #endif  
  55.     } else {  
  56.         puts("Unknown board, cannot configure pinmux.");  
  57.         hang();  
  58.     }  
  59. }  

另外,这个版本的u-boot有个bug,需要修改fat_register_device(fs/fat/fat.c)函数:

[cpp] view plain copy
  1. int fat_register_device(block_dev_desc_t *dev_desc, int part_no)  
  2. {  
  3.     disk_partition_t info;  
  4.   
  5.     /* First close any currently found FAT filesystem */  
  6.     cur_dev = NULL;  
  7.   
  8.     /* Read the partition table, if present */  
  9.     if (get_partition_info(dev_desc, part_no, &info)) {  
  10.         /*if (part_no != 0) { 
  11.             printf("** Partition %d not valid on device %d **\n", 
  12.                     part_no, dev_desc->dev); 
  13.             return -1; 
  14.         }*/  
  15.   
  16.         info.start = 0;  
  17.         info.size = dev_desc->lba;  
  18.         info.blksz = dev_desc->blksz;  
  19.         info.name[0] = 0;  
  20.         info.type[0] = 0;  
  21.         info.bootable = 0;  
  22. #ifdef CONFIG_PARTITION_UUIDS  
  23.         info.uuid[0] = 0;  
  24. #endif  
  25.     }  
  26.   
  27.     return fat_set_blk_dev(dev_desc, &info);  
  28. }  
至此,u-boot就已经可以启动了,但是有多余的步骤和log,不过可以去掉,修改file_fat_read_at(fs/fat/fat.c)函数:
[cpp] view plain copy
  1. long file_fat_read_at(const char *filename, unsigned long pos, void *buffer,  
  2.               unsigned long maxsize)  
  3. {  
  4.     debug("reading %s\n", filename);  
  5.     return do_fat_read_at(filename, pos, buffer, maxsize, LS_NO, 0);  
  6. }  
最后,TQ335x是MLO启动u-boot,然后u-boot去启动内核,故可以去掉配置项CONFIG_SPL_OS_BOOT,具体的修改文件include/configs/ti_armv7_common.h:
[cpp] view plain copy
  1. #if defined(CONFIG_SPL_OS_BOOT_ENABLE)  
  2. #define CONFIG_SPL_OS_BOOT  
  3. #endif  

至此,u-boot的移植工作就完成了,编译方法如下:

[cpp] view plain copy
  1. make ARCH=arm CROSS_COMPILE=arm-linux-gnueabi- am335x_evm_defconfig  
  2. make ARCH=arm CROSS_COMPILE=arm-linux-gnueabi- -j8  

其中,arm-linux-gnueabi-需要根据自己的交叉编译工具链前缀进行修改。完成u-boot的移植工作后我们来研究如何启动内核。


源码下载地址:

u-boot-2014.10 for TQ335x/TQ3358(SD卡启动)


原创粉丝点击