开发备忘录

setenv bootcmd_android_recovery 'run bootargs_base bootargs_android_recovery;mmc read 0 ${loadaddr} 0x7AA00 0x2000;bootm'


fastboot烧写
首先进入uboot命令行
setenv fastboot_dev mmc0 
fas
然后在dos
按照需要烧写：
fastboot flash bootloader \\192.168.40.243\work\imx_r10.2_myandroid\bootable\bootloader\uboot-imx\u-boot-no-padding.bin
fastboot flash bootloader \\192.168.40.243\work\lhyz\myandroid-r94-ok\bootable\bootloader\uboot-imx\u-boot-no-padding.bin
fastboot flash bootloader \\192.168.40.243\work\lhyz\myandroid-r9.2.1\bootable\bootloader\uboot-imx\u-boot-no-padding.bin
fastboot flash recovery \\192.168.40.243\work\lhyz\myandroid-r9.2.1\out\target\product\imx51_bbg\recovery.img




fastboot flash kernel \\192.168.40.243\work\lhyz\myandroid-r9.2.1\kernel_imx\arch\arm\boot\uImage
fastboot flash system \\192.168.40.243\work\lhyz\myandroid-r9.2.1\out\target\product\imx51_bbg\system.img
fastboot flash uramdisk \\192.168.40.243\work\lhyz\myandroid-r9.2.1\out\target\product\imx51_bbg\uramdisk.img
fastboot flash userdata \\192.168.40.243\work\lhyz\myandroid-r9.2.1\out\target\product\imx51_bbg\userdata.img
fastboot flash kernel \\192.168.0.243\work\lhyz\myandroid-r94-ok\kernel_imx\arch\arm\boot\uImage
fastboot flash system \\192.168.0.243\work\lhyz\myandroid-r94-ok\out\target\product\imx51_bbg\system.img
fastboot flash uramdisk \\192.168.0.243\work\lhyz\myandroid-r94-ok\out\target\product\imx51_bbg\uramdisk.img


fastboot flash kernel \\192.168.40.243\work\lhyz\kernel_imx_r92\arch\arm\boot\uImage
fastboot flash kernel \\192.168.40.243\work\lhyz\kernel_imx_t3\arch\arm\boot\uImage
fastboot flash kernel \\192.168.40.243\work\lhyz\kernel_imx_1064\arch\arm\boot\uImage
fastboot flash uramdisk \\192.168.40.243\work\lhyz\myandroid-r94-ok\out\target\product\imx51_bbg\uramdisk.img
fastboot flash uramdisk \\192.168.0.100\share\903\image\t3\uramdisk.img
fastboot flash system \\192.168.0.100\share\903\image\t3\system.img
fastboot flash system \\192.168.0.100\share\903\image\wei\0827\system.img
fastboot flash uramdisk \\192.168.0.100\share\903\image\wei\0827\uramdisk.img
fastboot flash uramdisk \\192.168.0.100\share\903\image\SD_sfdisk\uramdisk.img
fastboot flash userdata \\192.168.40.243\work\lhyz\t3_image\userdata.img
烧完后重启
fastboot reboot




fastboot flash bootloader Y:\fsl\myandroid_r9.2.1\bootable\bootloader\uboot-imx\u-boot-no-padding.bin


分区内核，要先烧这个u-boot-no-padding.bin
fastboot flash bootloader D:\hui\lhyz\project\903\tools\SD_sfdisk\u-boot-no-padding.bin
fastboot flash kernel D:\hui\lhyz\project\903\tools\SD_sfdisk\uImage
fastboot flash uramdisk D:\hui\lhyz\project\903\tools\SD_sfdisk\uramdisk.img


烧广告机固件
fastboot flash kernel Y:\fsl\myandroid_r9.2.1\kernel_imx\arch\arm\boot\uImage
fastboot flash uramdisk Y:\fsl\myandroid_r9.2.1\out\target\product\imx51_bbg\uramdisk.img
fastboot flash system Y:\fsl\myandroid_r9.2.1\out\target\product\imx51_bbg\system.img
fastboot reboot




setenv bootargs_android 'console=ttymxc0 video=mxcdi0fb:RGB24,720P60 video=mxcdi1fb:RGB565,1024x768M@55 di1_primary gpu_memory=32M ip=off root=/dev/nfs init=/init nfsroot=192.168.0.10:/nfs/rootfs ip=192.168.0.100::::usb0 androidboot.console=ttymxc0 '




git 常用命令
./repo init -u git://192.168.1.25/platform/manifest.git -b r10.2_t4 //初始化
repo init -u ssh://TaiDaxun@61.143.53.198/git_repo/manifest.git
git reset --hard ORIG_HEAD //回退到原始版本
git pull          //从服务器更新代码到本地


一、打tag的命令是先hard reset到自己模块(包含自己和组员)最后一次提交的位置，然后git tag tagname。Tagname的取法要统一，小项目名+完成阶段+日期。比如bsp完成了第二阶段的目标（7月6号的阶段目标），就可以命令tag为bsp-phase2-20110630
如果碰到没有全部完成，但是需要进release测试的，就把tag冠名ongoing, 如bsp-ongoing-20110630
如果碰到完成了某个bugfix，就 把BUG Number包含进去，如bsp-PRxxx-20110630 (PR指ProblemResolve,xxx指bug在JIRA系统里的编号)


二、上传tag的命令是git push review --tags
一、tag的命名加一个“工程名”的字段即 “工程名-小项目名-完成阶段-日期”;这样曾良均做整合版本的时候就知道android下有哪些工程有了需要包含的修改；


二、打tag可以指定位置，命令格式为git tag tagname commit，如git tag kernel_imx-pwrsave-phase2-20110631 cd8c0beb9ecec5e68c0535a416aea972d5f67251


三、上传某个特定tag的命令是git push review tagname.这样可以避免把本地自己命名的tag误传到服务器。




#uboot读取seltest uramdisk改成3M
setenv bootcmd_selftest 'mmc read 1 ${loadaddr} 0x3800 0x2000;mmc read 1 ${rd_loadaddr} 0x5800 0x2000;'


setenv bootargs 'console=ttymxc0 init=/linuxrc androidboot.console=ttymxc0 video=mxcdi0fb:RGB666,XGA ldb=di0 di0_primary ip=off gpu_nommu,gpu_memory=64M'


#写乱mmc uboot参数区,可清除所有变量,用默认设置
mmc write 0 91000000 600 10


sf probe 0:1
sf erase d0000 1000




#SD卡启动Android时，默认讲system挂载为只读，把system挂载为可读可写模式，在kernel串口命令行下打入如下命令：
mount -o remount -rw /dev/block/mmcblk1p2 /system
mount -o remount -rw /dev/block/mmcblk0p2 /system
mount -o remount -rw /dev/block/nandd /system
mount -o remount -rw emmc@android /system




git review服务器:192.168.1.25
git发邮件脚本: /home/git/repositories/android/platform/bionic.git/hooks/post-receive


mx51 903 uboot参数：


setenv bootcmd 'run bootcmd_SD1 bootcmd_SD2'




setenv bootcmd_SD1 'run bootargs_base bootargs_android'




setenv bootcmd_SD2 'mmc read 0 ${loadaddr} 0x800 0x1800;mmc read 0 ${rd_loadaddr} 0x3000 0x2600;bootm ${loadaddr} ${rd_loadaddr}'




setenv bootargs_base 'setenv bootargs console=ttymxc0,115200'




setenv bootargs_android 'setenv bootargs ${bootargs} init=/init androidboot.console=ttymxc0 video=mxcdi0fb:RGB24,XGA video=mxcdi1fb:RGB565,1024x768M@60 di1_primary gpu_memory=32M calibration'




setenv loadaddr '0x90800000'




setenv rd_loadaddr '0x90C00000'




setenv netdev 'eth0'




setenv ethprime 'FEC0'




setenv uboot_addr '0xa0000000'




setenv uboot 'u-boot.bin'




setenv kernel 'uImage'




setenv rd_loadaddr '0x90C00000'




setenv nfsroot '/opt/eldk/arm'




setenv bootargs_base 'setenv bootargs console=ttymxc0,115200 gpu_memory=16M'




setenv bootargs_nfs 'setenv bootargs ${bootargs} root=/dev/nfs ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp'




setenv bootcmd_net 'run bootargs_base bootargs_nfs; tftpboot ${loadaddr} ${kernel}; bootm'




setenv prg_uboot 'tftpboot ${loadaddr} ${uboot}; protect off ${uboot_addr} 0xa003ffff; erase ${uboot_addr} 0xa003ffff; cp.b ${loadaddr} ${uboot_addr} ${filesize};'




setenv bootcmd 'run bootcmd_SD' 




setenv bootcmd_SD 'run bootargs_base bootargs_android;mmc read 0 ${loadaddr} 0x800 2000;mmc read 0 ${rd_loadaddr} 0x3000 0x258;bootm ${loadaddr}'




setenv bootcmd_android_recovery 'run bootargs_base bootargs_android_recovery;mmc read 0 ${loadaddr} 0x800 0x2000;bootm'




setenv bootargs_android_recovery 'setenv bootargs ${bootargs} init=/init root=/dev/mmcblk0p4 rootfs=ext4 video=mxcdi0fb:RGB24,XGA video=mxcdi1fb:RGB565,1024x768M@60 di1_primary gpu_memory=32M'




setenv stdin 'serial'




setenv stdout 'serial'




setenv stderr 'serial'




setenv ethact 'FEC0'


1001广告机：
setenv bootcmd_SD2 'mmc read 0 ${loadaddr} 0x800 0x1800;mmc read 0 ${rd_loadaddr} 0x3000 0x3000;bootm ${loadaddr} ${rd_loadaddr}'




mx51 uboot参数: 


setenv bootdelay '1'


setenv loadaddr '0x90800000'


setenv rd_loadaddr '0x90B00000'


setenv crc_mode '0'


setenv kernel_mode ''


setenv ubootversion 'uboot_version=05/04/11'


setenv bootcmd 'run bootcmd_nand'


setenv nand_read_kernel 'nand read ${loadaddr} 0x0 0x500000'


setenv nand_read_rd 'nand read ${rd_loadaddr} 0x500000  0x200000'


setenv bootcmd_nand 'run bootargs_base bootargs_android bootargs_nand; run nand_read_kernel; run nand_read_rd; bootm ${loadaddr} ${rd_loadaddr}'


setenv bootargs_base 'setenv bootargs console=ttymxc0,115200'


setenv bootargs_nand 'setenv bootargs ${bootargs} ubi.mtd=4'


setenv bootargs_android 'setenv bootargs ${bootargs} init=/init androidboot.console=ttymxc0 ${ubootversion} ${kernel_mode} video=mxcdi0fb:RGB24,800x600M@60 video=mxcdi1fb:YUV444,720P60 tve di1_primary'


setenv netdev 'eth0'


setenv ethprime 'FEC0'


setenv uboot_addr '0xa0000000'


setenv uboot 'u-boot.bin'


setenv kernel 'uImage'


setenv nfsroot '/opt/eldk/arm'


setenv bootargs_nfs 'setenv bootargs ${bootargs} root=/dev/nfs ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp'


setenv bootcmd_net1 'run bootargs_base bootargs_nfs; tftpboot ${loadaddr} ${kernel}; bootm '


setenv bootcmd_net '${bootcmd_net1} mmcinit;cp.b 0x100000 ${loadaddr} 0x250000; cp.b 0x400000 ${rd_loadaddr} 0x4B000; bootm ${loadaddr} ${rd_loadaddr}'


setenv prg_uboot1 'tftpboot ${loadaddr} ${uboot}; protect off ${uboot_addr} 0xa003ffff; '


setenv prg_uboot '${prg_uboot1} erase ${uboot_addr} 0xa003ffff; cp.b ${loadaddr} ${uboot_addr} ${filesize}; bootargs=console=ttymxc0,115200 ip=dhcp mem=480M init=/init wvga calibration'


setenv bootcmd_SD1 'run bootargs_base bootargs_android bootargs_SD'


setenv bootcmd_SD2 'mmc read 0 ${loadaddr} 0x800 0x1800;mmc read 0 ${rd_loadaddr} 0x2000 0x1000;bootm ${loadaddr} ${rd_loadaddr}'


setenv bootargs_SD 'setenv bootargs ${bootargs}'


setenv mtdparts 'mtdparts=nand0:0x500000@0x0(KERNEL),0x200000@0x500000(RAMDISK),0x100000@0x700000(MISC),0x1400000@0x800000(RECOVERY),-@0x1c00000(ROOT)'


setenv mtdids 'nand0=nand0'


setenv partition 'nand0,4'


setenv mtddevnum '4'


setenv mtddevname 'ROOT'


setenv ethact 'FEC0'


saveenv


 




mx51 R10.1 SD卡启动 uboot参数:


setenv loadaddr '0x90800000'


setenv rd_loadaddr '0x90D00000'


setenv bootargs 'console=ttymxc0,115200'


setenv bootargs_android 'init=/init root=/dev/mmcblk0p2 rootfstype=ext4 console=ttymxc0,115200 gpu_memory=16M androidboot.console=ttymxc0 video=mxcdi0fb:800x600M@60 ${ubootversion} ${kernel_mode} di1_primary'


setenv bootargs_base 'init=/init root=/dev/mmcblk0p2 rootfstype=ext4 console=ttymxc0,115200 gpu_memory=16M androidboot.console=ttymxc0 video=mxcdi0fb:800x600M@60 ${ubootversion} ${kernel_mode} di1_primary`


setenv bootcmd_SD1 'mmc read 0 ${loadaddr} 0x800 0x2000'


setenv bootcmd_SD2 'mmc read 0 ${rd_loadaddr} 0x3000 0x300;bootm ${loadaddr} ${rd_loadaddr}'


setenv bootcmd 'run bootcmd_SD1 bootcmd_SD2'


saveenv




mx53 uboot参数:
setenv baudrate '115200'
setenv loadaddr '0x70800000'
setenv netdev 'eth0'
setenv ethprime 'FEC0'
setenv uboot 'u-boot.bin'
setenv kernel 'uImage'
setenv loadaddr '0x70800000'
setenv rd_loadaddr '0x70D00000'
setenv nfsroot '/opt/eldk/arm'
setenv bootargs_base 'setenv bootargs console=ttymxc0,115200'
setenv bootargs_nfs 'setenv bootargs ${bootargs} root=/dev/nfs init=/init nfsroot=192.168.0.10:/nfs/rootfs ip=192.168.0.100::::usb0 console=ttymxc0,115200 console=tty0,v3,tcp'
setenv bootargs_android 'setenv bootargs ${bootargs} androidboot.console=ttymxc0 init=/init di1_primary video=mxcdi1fb:RGB666,XGA hdmi ldb=di1 gpu_memory=32M'
setenv bootcmd 'run bootcmd_SD; bootm ${loadaddr} ${rd_loadaddr}' 
setenv bootcmd_eMMC 'run bootargs_base bootargs_android;mmc read 1 ${loadaddr} 0x800 2000;mmc read 1 ${rd_loadaddr} 0x3000 0x258;bootm ${loadaddr} ${rd_loadaddr}'
setenv bootcmd_net 'run bootargs_base bootargs_nfs; tftpboot ${loadaddr} ${kernel}; bootm'
setenv bootcmd_android_recovery 'run bootargs_base bootargs_android_recovery;mmc read 0 ${loadaddr} 0x800 0x2000;bootm
bootargs_android_recovery=setenv bootargs ${bootargs} init=/init root=/dev/mmcblk0p4 rootfs=ext4'
setenv bootargs 'console=ttymxc0 init=/init androidboot.console=ttymxc0 video=mxcdi0fb:RGB666,XGA ldb=di0 di0_primary ip=off gpu_nommu,gpu_memory=64M'
setenv ethact 'FEC0'
setenv bootcmd_SD 'mmc read 0 ${loadaddr} 0x800 0x2000; mmc read 0 ${rd_loadaddr} 0x3000 0x1000;'
setenv stdin 'serial'
setenv stdout 'serial'
setenv stderr 'serial'


saveenv


NFS启动:
setenv bootcmd 'run bootcmd_eMMC; bootm ${loadaddr} ${rd_loadaddr}'
setenv bootargs_base 'setenv bootargs ${bootargs} root=/dev/nfs init=/init nfsroot=192.168.0.10:/nfs/rootfs ip=192.168.0.100::::usb0'
setenv bootargs 'console=ttymxc0 video=mxcdi0fb:RGB666,vga ldb=di0 di0_primary ip=off gpu_nommu,gpu_memory=64M root=/dev/nfs init=/init nfsroot=192.168.0.10:/nfs/rootfs ip=192.168.0.100::::usb0 androidboot.console=ttymxc0 '
setenv bootargs 'console=ttymxc0 di1_primary video=mxcdi1fb:RGB666,VGA-SVGA ldb=di1 gpu_memory=32M ip=off root=/dev/nfs init=/init nfsroot=192.168.0.10:/nfs/rootfs ip=192.168.0.100::::usb0 androidboot.console=ttymxc0 '
903 nfs:
setenv bootargs_nfs 'setenv bootargs ${bootargs} ip=off root=/dev/nfs init=/init nfsroot=192.168.0.10:/nfs/rootfs ip=192.168.0.100::::usb0,v3,tcp'




setenv bootargs_android 'setenv bootargs ${bootargs} ${bootargs_nfs} video=mxcdi0fb:RGB24,720P60 video=mxcdi1fb:RGB565,1024x768M@55 di1_primary gpu_memory=32M androidboot.console=ttymxc0 '


 
imx53_smd开发板uboot参数:
setenv ethaddr 00:04:9f:00:ea:d3
setenv fec_addr 00:04:9f:00:ea:d3
setenv loadaddr 0x70800000          
setenv rd_loadaddr 0x70D00000       
setenv bootcmd 'run bootcmd_SD; bootm ${loadaddr} ${rd_loadaddr}' 
setenv bootcmd_SD 'mmc read 0 ${loadaddr} 0x800 0x3000; mmc read 0 ${rd_loadaddr} 0x3000 0x300;'
setenv bootargs 'console=ttymxc0,115200 init=/init androidboot.console=ttymxc0 video=mxcdi1fb:RGB666,XGA ldb=di1 di1_primary ip=off gpu_memory=64M'
saveenv


setenv bootcmd_SD 'mmc read 0 ${loadaddr} 0x800 0x2000; mmc read 0 ${rd_loadaddr} 0x3000 0x1000;'


格式化SD卡
sudo mkfs.vfat /dev/sdb1
sudo mkfs.ext4 /dev/sdb2 -O ^extent -L system
sudo mkfs.ext4 /dev/sdb4 -O ^extent -L recovery
sudo mkfs.ext4 /dev/sdb5 -O ^extent -L data
sudo mkfs.ext4 /dev/sdb6 -O ^extent -L cache
复制系统文件到SD卡
sudo dd if=u-boot.bin of=/dev/sdb bs=1K skip=1 seek=1; sync
sudo dd if=uImage of=/dev/sdb bs=1M seek=1; sync
sudo dd if=SD/uramdisk.img of=/dev/sdb bs=1M seek=6; sync
sudo dd if=SD/system.img of=/dev/sdb2 bs=128k; sync


sudo dd if=/home/bill/work/mx53/r10.2_t4/kernel_imx/arch/arm/boot/uImage of=/dev/sdb bs=1M seek=1; sync
sudo dd if=/home/bill/work/mx53/r10.2_t4/out/target/product/imx53_smd/uramdisk.img of=/dev/sdb bs=1M seek=6; sync
sudo dd if=/home/bill/work/mx53/r10.2_t4/out/target/product/imx53_smd/recovery.img of=/dev/sdb4; sync
sudo dd if=/home/bill/work/mx53/r10.2_t4/out/target/product/imx53_smd/system.img of=/dev/sdb2 bs=128k; sync


 
使用 logcat程序来查看系统的日志。 
Logcat的日志输出分类： 
Logcat             ?查看所有LOG 
logcat –b radio        ?查看系统radio模块日志 
logcat –s ZTEMT      ?查看ZTEMT分类日志 
logcat –s ZTEMT-AT   ?查看ZTEMT-AT 分类日志 


#创建视频需要的节点
mknod /dev/null c 1 3
mknod /dev/console c 5 1
/bin/busybox mknod /dev/fb0 c 29 0
/bin/busybox mknod /dev/fb1 c 29 1
/bin/busybox mknod /dev/fb2 c 29 2
mknod /dev/video0 c 81 0
mknod /dev/video16 c 81 1


./mxc_v4l2_overlay.out -iw 800 -ih 480 -ow 800 -oh 480 -it 20 -il 140 -r 0 -fr 30 -fg -t 10
/unit_tests/mxc_v4l2_overlay.out -iw 800 -ih 480 -ow 720 -oh 480 -it 0 -il 0 -r 0 -fr 30 -fg -t 1200


rm /dev/tty
ln -s /dev/ttymxc0 /dev/tty
/data/t232


#初始化MCU
hffaa8001010a
hffaa8001010a
hffaa8101010a


#切换到DVD模式
hffaa8d01010a
hffaa8e00010a


hffaa8d05010a


#切换到ARM模式
hffaa8d0a010a
hffaa8e00010a


#调节功放音量
hffaa8b08180a


#蓝牙电源
echo 1 > /sys/class/rfkill/rfkill0/state


#调试摄像头
adb push \\192.168.40.248\work\zh\camera\rgb_4p\rgb_4p system/bin
chmod 777 /system/bin/rgb_4p
rgb_4p 320 240 16 0 0




\\192.168.40.248\work\zh\myandroid_R9\bootable\bootloader\uboot-imx-nand\u-boot.bin
\\192.168.40.248\work\zh\myandroid_R9\kernel_imx\arch\arm\boot\uImage
\\192.168.40.248\work\zh\myandroid_R9\out\target\product\imx51_bbg\android_root.img
\\192.168.40.248\work\zh\myandroid_R9\out\target\product\imx51_bbg\uramdisk.img


\\192.168.0.97\all\home\hui\myandroid_R9\trunk\kernel_imx\arch\arm\boot\uImage
\\192.168.0.97\all\home\hui\myandroid_R9\trunk\out\target\product\imx51_bbg\android_root.img


#用ATK工具烧写文件到nand
00000000 uboot
00300000 uImage
00600000 uramdisk
00800000 android_recovery //注意,有分2k page和4k page,打包方法如下介绍
01C00000 android_root //注意,有分2k page和4k page,打包方法如下介绍


#删除触摸屏校准文件,开机重新校准
rm /data/system/calibration


打包成uboot可识别的内核:
mkimage -A arm -O linux -T kernel -C none -a 0x90008000 -e 0x90008000 -n "Android Linux Kernel" -d arch/arm/boot/Image arch/arm/boot/uImage_nozip


在Android下打包uboot可识别的uramdisk:
out/host/linux-x86/bin/mkbootfs out/target/product/imx51_bbg/root | out/host/linux-x86/bin/minigzip > out/target/product/imx51_bbg/ramdisk.img
bootable/bootloader/uboot-imx/tools/mkimage  -A arm -O linux -T ramdisk -C none -a 0x90308000 -n "Android Root Filesystem" -d out/target/product/imx51_bbg/ramdisk.img out/target/product/imx51_bbg/uramdisk.img
#mx53
out/host/linux-x86/bin/mkbootfs out/target/product/imx53_smd/rootfs | out/host/linux-x86/bin/minigzip > out/target/product/imx53_smd/ramdisk.img
bootable/bootloader/uboot-imx/tools/mkimage  -A arm -O linux -T ramdisk -C none -a 0x70308000 -n "Android Root Filesystem" -d out/target/product/imx53_smd/ramdisk.img out/target/product/imx53_smd/uramdisk.img


在Android下打包SD卡启动的system.img:
【1】解压SD卡格式的system.img到目录abc，
mkdir abc
sudo mount system.img -o loop abc/
【2】把需要修改的内容复制到abc，如开机动画bootanimation.zip
cp bootanimation.zip abc/media
【3】直接sudo umount abc/ 即可
或者
【3】把abc目录打包回system.img
su进入超级用户root模式


num_blocks=`du -sk out/target/product/imx51_bbg/system | tail -n1 | awk '{print $1;}'`; if [ $num_blocks -lt 20480 ]; then extra_blocks=3072; else extra_blocks=20480; fi ; if [ "" != "" ]; then num_blocks=; num_inodes=4096; else num_blocks=`expr $num_blocks + $extra_blocks` ; num_inodes=`find out/target/product/imx51_bbg/system | wc -l` ; num_inodes=`expr $num_inodes + 500`; fi; out/host/linux-x86/bin/genext2fs -a -d out/target/product/imx51_bbg/system -b $num_blocks -N $num_inodes -m 0 out/target/product/imx51_bbg/obj/PACKAGING/systemimage_unopt_intermediates/system.img;
tune2fs -L system out/target/product/imx51_bbg/obj/PACKAGING/systemimage_unopt_intermediates/system.img
tune2fs -j out/target/product/imx51_bbg/obj/PACKAGING/systemimage_unopt_intermediates/system.img
tune2fs -O uninit_bg,dir_index out/target/product/imx51_bbg/obj/PACKAGING/systemimage_unopt_intermediates/system.img
tune2fs -C 1 out/target/product/imx51_bbg/obj/PACKAGING/systemimage_unopt_intermediates/system.img
e2fsck -fyD out/target/product/imx51_bbg/obj/PACKAGING/systemimage_unopt_intermediates/system.img ; 
out/host/linux-x86/bin/acp -fpt out/target/product/imx51_bbg/obj/PACKAGING/systemimage_unopt_intermediates/system.img out/target/product/imx51_bbg/system.img




在Android下打包UBI文件系统android_root.img,android_recovery.img:
#2K page:
out/host/linux-x86/bin/mkfs.ubifs -d out/target/product/imx51_bbg/system -o out/target/product/imx51_bbg/obj/PACKAGING/systemimage_unopt_intermediates/system.img -m 2048 -e 129024 -c 2048 -x none
out/host/linux-x86/bin/acp -fpt out/target/product/imx51_bbg/obj/PACKAGING/systemimage_unopt_intermediates/system.img out/target/product/imx51_bbg/system.img
out/host/linux-x86/bin/mkfs.ubifs -d out/target/product/imx51_bbg/data -o out/target/product/imx51_bbg/userdata.img -m 2048 -e 129024 -c 2048 -x none
out/host/linux-x86/bin/ubinize -o out/target/product/imx51_bbg/android_root.img -m 2048 -p 128KiB -s 512 -O 512 out/target/product/imx51_bbg/ubinize.ini
out/host/linux-x86/bin/mkfs.ubifs -d out/target/product/imx51_bbg/recovery/root -o out/target/product/imx51_bbg/recovery.img -m 2048 -e 129024 -c 2048 -x none
out/host/linux-x86/bin/ubinize -o out/target/product/imx51_bbg/android_recovery.img -m 2048 -p 128KiB -s 512 -O 512 out/target/product/imx51_bbg/ubinize_reco.ini


#4K page:
out/host/linux-x86/bin/mkfs.ubifs -d out/target/product/imx51_bbg/system -o out/target/product/imx51_bbg/obj/PACKAGING/systemimage_unopt_intermediates/system.img -m 4096 -e 516096 -c 4096 -x none
out/host/linux-x86/bin/acp -fpt out/target/product/imx51_bbg/obj/PACKAGING/systemimage_unopt_intermediates/system.img out/target/product/imx51_bbg/system.img
out/host/linux-x86/bin/mkfs.ubifs -d out/target/product/imx51_bbg/data -o out/target/product/imx51_bbg/userdata.img -m 4096 -e 516096 -c 4096 -x none
out/host/linux-x86/bin/ubinize -o out/target/product/imx51_bbg/android_root.img -m 4096 -p 512KiB out/target/product/imx51_bbg/ubinize.ini
out/host/linux-x86/bin/mkfs.ubifs -d out/target/product/imx51_bbg/recovery/root -o out/target/product/imx51_bbg/recovery.img -m 4096 -e 516096 -c 40 -x none
out/host/linux-x86/bin/ubinize -o out/target/product/imx51_bbg/android_recovery.img -m 4096 -p 512KiB out/target/product/imx51_bbg/ubinize_reco.ini


编译内核要编译成uImage：
make uImage -j2 ARCH=arm CROSS_COMPILE=arm-linux-


生成uboot能识别的uramdisk:
~/work/android_r9/myandroid_R9/bootable/bootloader/uboot-imx/tools/mkimage  -A arm -O linux -T ramdisk -C none -a 0x70308000 -n "Android Root Filesystem" -d ./ramdisk.img ./uramdisk.img


\\192.168.40.248\work\android_r9\myandroid_R9\kernel_imx\arch\arm\boot\uImage


kernel启动命令行的一些设置：
noinitrd console=ttymxc0,115200 root=/dev/mtdblock2 rw rootfstype=jffs2 ip=off
root=/dev/nfs init=/init nfsroot=192.168.1.10:/nfs/rootfs ip=192.168.1.100 console=ttymxc0,115200 fbcon=rotate:1 
root=/dev/mtdblock2 rw rootfstype=ubifs noinitrd mtdparts=nand_mtd:0x300000@0x300000(uImage),0x1c00000@0x10000000(rootfs) rw console=ttymxc0,115200 fbcon=rotate:1


U-Boot环境变量设置：
setenv nand_read_kernel 'nand read ${loadaddr} 0x300000 0x290000'
setenv nand_read_rd 'nand read ${rd_loadaddr} 0x600000 0x4B000'
setenv bootcmd_nand 'run bootargs_base bootargs_android bootargs_nand; run nand_read_kernel; run nand_read_rd; bootm ${loadaddr} ${rd_loadaddr}'
setenv bootargs_base 'setenv bootargs console=ttymxc0,115200'
setenv bootargs_nand 'setenv bootargs ${bootargs} ubi.mtd=3'
setenv bootargs_android 'setenv bootargs ${bootargs} init=/init androidboot.console=ttymxc0'
setenv loadaddr 0x90800000
setenv rd_loadaddr 0x90B00000


#busybox启动
setenv bootargs_android 'setenv bootargs ${bootargs} init=/linuxrc androidboot.console=ttymxc0'


#如果停留在Touchscreen Calibration界面,意思即校准触摸屏.如果不想校正,可去掉wvga calibration，跳过此界面
setenv bootargs_android 'setenv bootargs ${bootargs} init=/init androidboot.console=ttymxc0 console=tty0'
saveenv
#串口3（ttymxc2）用来做调试控制台
setenv bootargs_android 'setenv bootargs ${bootargs} init=/init androidboot.console=ttymxc2 console=tty0 wvga calibration'
setenv bootargs_base 'setenv bootargs console=ttymxc2,115200'
saveenv


NSF启动环境变量设置：
setenv bootargs_android 'setenv bootargs ${bootargs} root=/dev/nfs init=/init nfsroot=192.168.0.10:/nfs/rootfs ip=192.168.0.100::::usb0 console=ttymxc0,115200 console=tty0 wvga fbcon=rotate:1'
setenv bootargs_android 'setenv bootargs ${bootargs} root=/dev/nfs init=/init nfsroot=192.168.1.10:/nfs/rootfs ip=192.168.1.100::usb0 console=ttymxc0,115200 fbcon=rotate:1 video=mxcdi0fb:RGB565,800x480M-16@60 di0_primary wvga calibration'
setenv bootargs_android 'setenv bootargs ${bootargs} init=/init androidboot.console=ttymxc0 video=mxcdi0fb:RGB24,800x480M@60 video=mxcdi1fb:RGB24,800x480M@60 di0_primary calibration'
setenv bootargs_android 'setenv bootargs ${bootargs} init=/init androidboot.console=ttymxc0 video=mxcdi0fb:RGB24,800x480M@60 video=mxcdi1fb:YUV444,720P60 tve calibration'
mx51:
setenv bootargs_android 'setenv bootargs ${bootargs} root=/dev/nfs init=/init nfsroot=192.168.0.10:/nfs/rootfs ip=192.168.0.100::::usb0 androidboot.console=ttymxc0 video=mxcdi0fb:RGB24,800x600M@60 video=mxcdi1fb:RGB24,800x480M@60 di0_primary'


mxcdi1fb:TV-PAL


 


svn import --no-ignore uboot-imx-nand svn://192.168.0.97/iMx51_Android/Android2.2/trunk/bootable/bootloader/uboot-imx-nand -m "iMx51 android r9 nand uboot for ZhongHong" --username hui --password
svn import --no-ignore kernel_imx svn://192.168.0.97/iMx51_Android/Android2.2/trunk/ -m "iMx51 android r9 Linux-2.6.31 kernel for ZhongHong" --username hui --password
svn import --no-ignore kernel_imx svn://192.168.0.97/iMx51_Android/imx-android-r9.2/trunk  -m "iMx51 android r9.2 Linux-2.6.31 kernel for ZhongHong" --username hui --password 
svn import --no-ignore kernel_imx svn://192.168.0.97/iMx51_Android/imx-android-r10/trunk  -m "iMx51 android2.3 (BSP r10) Linux-2.6.35 kernel for ZhongHong" --username hui --password 
svn import --no-ignore luvcview_port https://192.168.0.121:8443/svn/BSP/Android/iMX51/Base/trunk/luvcview_port -m "quick camera preview project. add by hui" --username liuyh --password ***
svn import --no-ignore kernel_imx https://product/svn/903/myandroid_R9.2.1 -m "iMx51 android r92.2 kernel for product 903 of lhyz" --username bill --password
svn import --no-ignore myandroid-r94-ok https://product/svn/903_R9.4/myandroid_R9.4 -m "iMx51 android r92.2 kernel for product 903 R9.4 of lhyz" --username bill --password
svn import --no-ignore myandroid-r9.2.1 https://192.168.0.100/svn/903/myandroid_R9.2.1 -m "iMx51 android r92.2.1 orig android for product 903 of lhyz" --username bill --password
svn import --no-ignore starl https://192.168.0.100/svn/rk2918_byd/trunk/ -m "BYD rk2918 MID" --username bill --password
svn import --no-ignore sdk_2906 https://192.168.0.21/svn/rk_2906_v2.00/trunk/ -m "rk_2906_v2.00 for lhyz 760" --username bill --password


svn import --no-ignore 4.0 https://192.168.0.21/svn/A10_crane_sdk_v4.0.3_v1.5/trunk/ -m "A10_crane_sdk_v4.0.3_v1.5 for lhyz " --username bill --password
svn import --no-ignore exdroid4.1.1_r1-a10-v0.3 https://192.168.0.21/svn/exdroid4.1.1_r1-a10-v0.3/trunk/  -m "exdroid4.1.1_r1-a10-v0.3 for lhyz " --username bill --password
svn import --no-ignore A13 https://192.168.1.45/svn/A13_1.5/trunk  -m "A13_1.5 for tdx" --username bill --password
svn import --no-ignore 4.1_v1.2 https://192.168.1.45/svn/A13_4.1_v1.2/trunk  -m "A13_android4.1_v1.2 for tdx" --username bill --password
svn import --no-ignore 4.1_v1.0 https://192.168.1.45/svn/A13_4.1_v1.0/trunk  -m "A13_android4.1_v1.0 for tdx" --username bill --password
svn import --no-ignore exdroid4.1.1_r1-a10-v0.4release https://192.168.1.45/svn/A10_4.1_v1.2/trunk  -m "A13-4.1-v1.2 for tdx" --username bill --password
svn import --no-ignore exdroid4.0.4r1-a10-v1.5release https://192.168.1.45/svn/A10_4.0_v1.5/trunk  -m "exdroid4.0.4r1-a10-v1.5release for tdx" --username bill --password
svn import --no-ignore 4.0_git_orig https://192.168.1.169/svn/exdroid4.0.4r1-a10-v1.5release/trunk -m "exdroid4.0.4r1-a10-v1.5release for TDC " --username bill --password
svn import --no-ignore A13-4.2_importsvn https://192.168.1.169/svn/A13_4.2/trunk/ -m "A13_4.2 for TDC " --username bill --password
svn import --no-ignore 1322_alps https://192.168.1.169/svn/mbk89_tb_jb2/trunk/ -m "MTK8389 for TDC 1322" --username bill --password




由于svn服务器地址改变，原来check out的源码无法连接svn服务器，请用如下方法更新源码svn地址：
svn switch --relocate https://192.168.1.44/svn/A13_4.1_v1.2/trunk/lichee/linux-3.0/drivers/mmc/sunxi-host/ https://192.168.1.169/svn/A13_4.1_v1.2/trunk/lichee/linux-3.0/drivers/mmc/sunxi-host/


objdump -x libmedia_jni.so | grep NEEDED


logcat Vold:* *:S&
logcat Sensor:* *:S&
logcat SerialPort:* *:S&
logcat bluedroid:* *:S&
logcat glgpsd:* *:S&


chmod u+r /system/lib/*
ls -l /system/lib/*


 


 


SMDKC110:


dnw 40000000


U-Boot
onenand erase 0 80000;onenand  write 40000000 0 80000


zImage
dnw 40000000;onenand erase 600000 500000;onenand write 40000000 600000 500000;re


ramdisk
onenand erase b00000 300000;onenand write 40000000 b00000 300000


system.img
onenand erase e00000 7800000;onenand write.yaffs2 40000000 e00000 5A00000


userdata.img
onenand erase b800000 14800000;onenand write.yaffs 40000000 b800000 1080




onenand erase 0 10000000


onenand write 57e00000 0 40000


onenand erase 0 40000;onenand write c0008000 0 40000


当你uboot跑起来之后再用仿真器或者USB下载到c0008000 再用如下命令烧写.


SMDK6410:
Clean
onenand erase 04600000 02800000


U-Boot
onenand erase 0 40000;onenand write c0008000 0 40000
       测试：onenand erase 80000 80000;onenand write c0008000 80000 80000


zImage
dnw;onenand erase 600000 300000;onenand write c0008000 600000 300000;re


ramdisk
onenand erase 900000 100000;onenand write c0008000 900000 100000


system.img
onenand erase a00000 4300000;onenand write.yaffs2 c0008000 a00000  377F040


userdata.img
####onenand erase A000000 5E00000;onenand write.yaffs2 c0008000 A000000 2559C0
onenand erase A000000 5E00000;onenand write.yaffs2 c0008000 A000000      2559C0


onenand erase 4d00000 5300000




SMDKC100:
U-Boot
nand erase 0 40000;nand  write c0000000 0 40000
onenand erase 0 40000;onenand  write c0008000 0 40000


zImage
dnw;nand erase 600000 300000;nand write c0000000 600000 300000
dnw;onenand erase 600000 300000;onenand write c0008000 600000 300000;re


ramdisk
nand erase 900000 100000;nand write c0000000 900000 100000
onenand erase 900000 100000;onenand write c0008000 900000 100000


system.img
nand erase a00000 4300000;nand write.yaffs2 c0000000 a00000 352f980
onenand erase a00000 4300000;onenand write.yaffs2 c0008000 a00000 ?


userdata.img
nand erase 9000000 7000000;nand write.yaffs c0000000 9000000 840
onenand erase 9000000 7000000;onenand write.yaffs c0008000 9000000 840


 


root=/dev/nfs init=/init nfsroot=192.168.1.10:/nfs ip=192.168.1.100 console=ttySAC2,115200 no_console_suspend=1
root=/dev/nfs init=/init nfsroot=192.168.1.10:/nfs ip=192.168.1.100 console=ttySAC2,115200
console=ttySAC2,115200,mem=256M
nfs cdc
root=/dev/nfs init=/init nfsroot=192.168.1.10://nfsroot/rootfs ip=192.168.1.100 console=ttySAC2,115200 fbcon=rotate:1




root=/dev/nfs init=/init nfsroot=192.168.1.10:/nfs ip=192.168.1.100 console=tty0 console=ttySAC2,115200 fbcon=rotate:3
root=/dev/nfs init=/linuxrc nfsroot=192.168.1.10:/nfs ip=192.168.1.100 console=tty0 console=ttySAC2,115200 fbcon=rotate:3


#邱俊涛svn linux-2.6.27-android
init=/init console=ttySAC2,115200 root=/dev/nfs nfsroot=192.168.1.110:/home/win_share/root ip=192.168.1.100:192.168.1.110:192.168.1.110:255.255.255.0:ubuntu9.04:usb0:off
init=/init console=ttySAC2,115200 root=/dev/nfs nfsroot=192.168.1.10:/nfs ip=192.168.1.100:192.168.1.1:192.168.1.1:255.255.255.0:ubuntu9.04:usb0:off


#linux2.6.24 onenand 配置
root=/dev/mtdblock2 rw rootfstype=jffs2 init=/linuxrc console=ttySAC2,115200
root=/dev/mtdblock3 rw rootfstype=jffs2 init=/linuxrc console=ttySAC2,115200
init=/linuxrc console=ttySAC2,115200


sudo smbmount //192.168.16.99/开发部/ /mnt/ -o iocharset=utf8,codepage=cp936,username=liuyihui,password=lyh2009
sudo smbmount //192.168.16.248/all/ ./mnt -o iocharset=utf8,codepage=cp936,username=lyh,password=23456
sudo smbmount //172.16.10.248/all/ ./mnt -o iocharset=utf8,codepage=cp936,username=hui,password=linux
sudo smbmount //192.168.0.97/Share/ /mnt -o iocharset=utf8,codepage=cp936,username=svn,password=


sudo smbmount //192.168.16.247/samsung  /mnt/ -o username=hui%pwd
sudo smbmount //192.168.16.247/android-1.5  /mnt/ -o username=hui%pwd




将luther_ramdisk.img打包成u-boot下载格式
mkimage -A arm -O linux -T ramdisk -C none -a 0x50800000 -n "ramdisk" -d luther_ramdisk.img luther_ramdisk.img-uboot.img


#在当前目录及其子目录下查找*.txt文件，并将查找到的文件信息显示出来。注意：{}和\之间有空格；不要少了最后的分号
find ./ -name "*.mk" -exec grep "apns" {} -nH \;
find . -type d -iname ".svn" -exec rm -rf {} \;
sed -i "s/原字符串/新字符串/g" `grep 原字符串 -rl 所在目录` 例如：把mahuinan替换为huinanma，执行命令：sed -i "s/mahuinan/huinanma/g" 'grep mahuinan -rl /www' 
find -name "*.php" |xargs perl -pi -e 's|21andy.com|www.21andy.com|g';以上表示：在当前目录及子目录下搜索所有后缀为 .php 的文件，并且将 字符串 21andy.com 替换成 www.21andy.com


询Linux应用程序运行依赖哪些库
arm-linux-objdump -x rootfs_imx_test/usr/sbin/lsusb | grep NEED


改变控制台debug消息显示级别，可以打印printk(DEBUG ...)信息
echo > /proc/sys/kernel/printk "8"


把system.img挂载区重新挂到可写
mount -o rw,remount -t yaffs2 /dev/block/mtdblock0 /system
mount -o rw,remount -t yaffs2 /dev/block/mmcblk0 /system






echo "at">/dev/ttyspi0


./memdmp E0200E00 182


md e0200f00


 


./configure --with-linux=/home/hui/work/zh/myandroid_R9/kernel_imx --host=arm-linux


#有的编译器没有arm-linux-,编译某些代码需要arm-linux-，因此需要链接
ln -s arm-eabi-addr2line arm-linux-addr2line 
ln -s arm-eabi-ar arm-linux-ar
ln -s arm-eabi-as arm-linux-as 
ln -s arm-eabi-c++ arm-linux-c++
ln -s arm-eabi-c++filt arm-linux-c++filt 
ln -s arm-eabi-cpp arm-linux-cpp 
ln -s arm-eabi-g++ arm-linux-g++ 
ln -s arm-eabi-gcc arm-linux-gcc
ln -s arm-eabi-gccbug arm-linux-gccbug 
ln -s arm-eabi-gcov arm-linux-gcov 
ln -s arm-eabi-gdb arm-linux-gdb
ln -s arm-eabi-gdbtui arm-linux-gdbtui 
ln -s arm-eabi-gprof arm-linux-gprof 
ln -s arm-eabi-ld arm-linux-ld 
ln -s arm-eabi-nm arm-linux-nm 
ln -s arm-eabi-objcopy arm-linux-objcopy 
ln -s arm-eabi-objdump arm-linux-objdump 
ln -s arm-eabi-ranlib arm-linux-ranlib 
ln -s arm-eabi-readelf arm-linux-readelf 
ln -s arm-eabi-run arm-linux-run 
ln -s arm-eabi-size arm-linux-size 
ln -s arm-eabi-strings arm-linux-strings 
ln -s arm-eabi-strip arm-linux-strip 


export TARGET_TYPE=%MISSING%
export cross_stack_direction=-1
export cross_signum=64
export cross_linuxthreads=0


#启动停止svn服务
sudo svnserve -d  -r /home/root/
killall svnserve




不同3G模块移植
【1】
打开：out\target\product\imx51_bbg\root\init.rc
根据不同模块修改：
#ZTE C100, add by hui
service ril-daemon /system/bin/rild -l /system/lib/libreference-ril.so -- -d /dev/ttyUSB0 -u /dev/ttyUSB2
#WCDMA U6300V, add by hui
#service ril-daemon /system/bin/rild -l /system/lib/libreference-ril.so -- -d /dev/ttyUSB1 -u /dev/ttyUSB2
【2】
打开：out\target\product\imx51_bbg\system\etc\init.gprs-pppd
根据不同模块修改：
#below is config for U6300 WCDMA modem
/system/bin/pppd  /dev/ttyUSB2 9600 mru 1280 mtu 1280 nodetach debug dump defaultroute usepeerdns novj novjccomp noipdefault ipcp-accept-local ipcp-accept-remote connect-delay 5000 linkname ppp0
#below is config for ZTE CDMA modem
#/system/bin/pppd  /dev/ttyUSB0 115200 mru 1280 mtu 1280 nodetach debug dump defaultroute usepeerdns novj novjccomp noipdefault ipcp-accept-local ipcp-accept-remote connect-delay 5000 linkname ppp0 name "card" password "card"




在我们的工作经常要验证不同相同源码不同配置内核版本，比如imx51_evk,imx53_smd,imx53_t4.imx_51_t3,
可以针对每个配置生成一个.config,
mkdir imx53_smd
cp .config_imx53_smd imx53_smd/.config
make uImage O=imx53_smd -j4
mkdir imx53_t4
cp .config_imx53_t4 imx53_t4/.config
make uImage O=imx53_t4 -j4


备份M9短信,电话本数据库,
cat /data/data/com.android.providers.telephony/databases/mmssms.db > /sdcard/mmssms.db
cat /sdcard/mmssms.db > /data/data/com.android.providers.telephony/databases/mmssms.db
cat /data/data/com.android.providers.contacts/databases/contacts2.db > contacts2.db




这样备份LINUX
tar -cvpzf /media/Data/linux_bak.tgz –exclude=/proc –exclude=/lost+found –exclude=/media –exclude=/mnt –exclude=/sys / 


cpio解压绝对路径解决方法
cpio -iF initramfs --no-absolute-filenames


添加用户超级权限方法
sudo usermod -aG admin


更改目录用户拥有者
sudo chown liufc.liufc 目录名 -R


samba添加账户:
sudo smbpasswd -a LiSi
samba添加用户权限:
sudo vi /etc/samba/smb.conf
valid users=ZhangSan LiSi


RK内核编译需要安装：uudecode
sudo apt-get install sharutils


在init.rc不能直接/sbin/feedplayid
要用 exec /sbin/feedplayid 好了.


/system/bin/busybox find / -name dram
/system/bin/busybox find / -name ft5x_ts.ko
/system/bin/busybox lsusb


A10 fastboot烧固件
fastboot flash boot \\192.170.99.100\home\tdx\work\tdx\A13\android4.1\out\target\product\nuclear-evb\boot.img//往flash boot分区烧录boot.img


$fastboot flash system system.img //往flash system分区烧录system.img
fastboot flash system Z:\project\A10XX\4.0_svn\android4.0\out\target\product\crane-3g\system.img


$fastboot flash data userdata.img


查看wake_lock锁
cat /sys/power/wake_lock


A10打包system.img
mkuserimg.sh -s out/target/product/crane-iNote_v4/system out/target/product/crane-iNote_v4/obj/PACKAGING/systemimage_intermediates/system.img ext4 system 536870912
A10打包userdata.img
mkuserimg.sh -s out/target/product/crane-iNote_v4/data out/target/product/crane-iNote_v4/userdata.img ext4 data


/system/bin/busybox ifconfig


广东省深圳市宝安区建安二路流塘荔景新村38栋401


/data/data/com.android.settings/shared_prefs/com.android.settings_preferences.xml


A10下载源码
$ git clone ssh://TaiDaXun@61.143.53.198/git_repo/repo.git


1 、下载 android4.0 仓库 : ： username 替换成客户帐号的用户名
$ mkdir android4.0
$ cd android4.0
$ repo init -u ssh://TaiDaXun@61.143.53.198/git_repo/manifest.git
$ repo sync
$ repo start ics-exdroid --all
2 、下载 lichee (linux kernel) 代码 : username 替换成客户帐号的用户名
注意 ： 客户不要在 android4.0 目录下面去创建 lichee 目录 ， 否则初始化时不会生成新的 .rep o
文件，而是用上一级的 .repo 文件。最好在 android4.0 的同一级目录创建 lichee 目录。
$ cd ..
$ mkdir lichee
$ cd lichee
$ repo init -u ssh://TaiDaXun@61.143.53.198/git_repo/manifest.git -m lichee.xml
$ repo sync
$ repo start lichee-dev --all
3 、 更新 android4.1 代码： username 替换成客户帐号的用户名
$ mkdir android4.1
$ cd android4.1
$ repo init -u ssh://TaiDaXun@61.143.53.198/git_repo/manifest.git -b jb-exdroid
$ repo sync
$ repo start jb-exdroid --all
4 、 对应 android4.1 的 lichee 代码，更新地址如下： username 替换成客户帐号的用户名
$ mkdir lichee-jb
$ cd lichee-jb
$ repo init -u ssh://TaiDaXun@61.143.53.198/git_repo/manifest.git -b jb-exdroid -m lichee-jb.xml
$ repo sync
$ repo start lichee-jb --all




A13下载源码
电信网络使用 IP 地址： 61.143.53.198
1 、下载 android4.0 仓库： username 替换成客户帐号的用户名
$ mkdir android4.0
$ cd android4.0
$ repo init -u ssh://TaiDaXun@61.143.53.198/git_repo/manifest.git -m android_a13.xml
$ repo sync
全部下载完成之后，创建分支
$ repo start ics-exdroid --all
2 、 更新 android4.1 代码： username 替换成客户帐号的用户名
$ mkdir android4.1
$ cd android4. 1
$ repo init -u ssh://TaiDaXun@61.143.53.198/git_repo/manifest.git -b jb-exdroid -m android_a13.xml
$ repo sync
全部下载完成之后，创建分支
$ repo start jb-exdroid --all
3 、下载 lichee_a13 部分 (linux kernel 3.0) 代码： username 替换成客户帐号的用户名，
注意 ： 客户不要在 android4.0 目录下面去创建 lichee 目录 ， 否则初始化时不会生成新的 .rep o
文件，而是用上一级的 .repo 文件。最好在 android4.0 的同一级目录创建 lichee 目录。
$ cd ..
$ mkdir lichee
$ cd lichee
$ repo init -u ssh://TaiDaXun@61.143.53.198/git_repo/manifest.git -m lichee_a13.xml
$ repo sync
全部下载完成之后，创建分支
$ repo start a1x-dev --all


/system/bin/busybox find / -name ft5x_ts.ko
adb -s 20080411413fc082 push Z:\project\A10XX\indoor_terminal\lichee\linux-3.0\drivers\input\touchscreen\ft5x_ts.ko /system/vendor/modules/ft5x_ts.ko
adb -s 200804116818d41 push Z:\project\A13XX\A13-4.2\lichee\linux-3.0\drivers\input\touchscreen\ft5x_ts.ko /system/vendor/modules/ft5x_ts.ko
adb pull /system/build.prop d:\
adb push d:\build.prop /system/build.prop
mount -o remount -t ext4 -rw /dev/block/nandd /system
umount /system
/system/bin/busybox mount -t ext4 -o noatime,nosuid,nodev,barrier=0,journal_checksum,noauto_da_alloc /dev/block/nandd /system


/system/bin/busybox insmod /system/vendor/modules/sw_usb_mu509.ko
adb -s 20080411413fc082 push Z:\project\A10XX\C13_LCD7inch\android4.0\out\target\product\crane-3g\system\lib\libreference-ril.so /system/lib/
/system/bin/t232 115200 /dev/ttyUSB0


通过ssh拷贝文件夹
scp -r /home/cdf本地目录 root@192.168.1.123:/home/abc 




#改MAC地址 
/system/bin/busybox ifconfig eth0 down
/system/bin/busybox ifconfig eth0 hw ether 00:0C:18:EF:FF:ED
/system/bin/busybox ifconfig eth0 up


#SystemUI.apk,有返回按钮，状态栏
adb -s 20080411413fc082 push Z:\project\A10XX\C13_LCD7inch_old\android4.0\out\target\product\crane-3g\system\app\SystemUI.apk /system/app
#system目录改为可写，使得可以用adb push调试tvin库：
adb -s 20080411413fc082 push Z:\project\A10XX\C13_LCD7inch\android4.0\out\target\product\crane-3g\system\lib\libTvdJni.so /system/lib
adb -s 20080411413fc082 push Z:\project\A10XX\C13_LCD7inch\android4.0\out\target\product\crane-3g\system\lib\libtvdecoder.so /system/lib
adb -s 20080411413fc082 push Z:\project\A10XX\C13_LCD7inch\android4.0\out\target\product\crane-3g\system\lib\libenc_test.so /system/lib


chmod 777 /system/bin/t232
t232 115200 /dev/ttyUSB0
AT+CREG=2
H41542B435245473D320D0A
AT+CREG?
H41542B435245473FODOA
ATD13691956871
H41544431333639313935363837310D0A
H41544431383637363637393733310D0A


H41542B4353513D3F0D0A
AT回车
H41540D0A
H4154443131320D0A
H41544431303038360D0A


H41542B435245473F0D0A


9300按这个进入工程模式：
*#*#3646633#*#*




/system/bin/busybox ifconfig wlan0 212.123.5.211 netmask 255.255.0.0


把logcat记录保存在内存卡，然后pull到本地硬盘
logcat -b radio > /sdcard/logcat-b_radio.txt
adb -s C16-SEV850413fc082 pull /sdcard/logcat-b_radio.txt f:\tmp\


E:\download\android\NDK\android-ndk-r8e\ndk-build


MTK代码只编译内核new kernel
./mk mbk89_tb_jb2  n  k
./mk mbk89_tb_jb2  r bootimage


MTK代码编译步骤：
【1】如果修改过底层代码，通常要make update-api一次：
./mk -o=TARGET_BUILD_VARIANT=user mtk77_cu_ics2 update-api
【2】./mk -o=TARGET_BUILD_VARIANT=user mtk77_cu_ics2 new
【3】把packages\apps\prebuild_app\Phone.apk
复制到
out\target\product\mtk77_cu_ics2\system\app
【4】./mk -o=TARGET_BUILD_VARIANT=user mtk77_cu_ics2 systemimage


打包SD卡升级包方法：
./mk -o=TARGET_BUILD_VARIANT=user mtk77_cu_ics2 otapackage


全志gsensor旋转90度改法，需要删掉obj目录下的编译中间文件，因为有可能其它产品有编译过导致不会重新编译
SW_BOARD_USES_GSENSOR_TYPE := mma7660
SW_BOARD_GSENSOR_DIRECT_X := true
SW_BOARD_GSENSOR_DIRECT_Y := false
SW_BOARD_GSENSOR_XY_REVERT := false
rm -fr out/target/product/crane-G70/obj/SHARED_LIBRARIES/sensors.exDroid_intermediates/AccelSensor.P
rm -fr out/target/product/crane-G70/obj/SHARED_LIBRARIES/sensors.exDroid_intermediates/AccelSensor.o
mmm device/softwinner/common/hardware/libsensors/
pack