MitraStar DSL-2401HN-T1C-GV硬件与启动信息

硬件

SoC MT7510T - MediaTek xDSL SoC (MIPS 34Kc 650 MHz ) RAM M14D5121632A - ESMT 512 Mbit (64 MB) DDR2 SDRAM Flash MX30LF1G18AC - Macronix 1 Gbit (128 MB) NAND Switch Integrado USB Não Wireless MT7592N - MediaTek 2×2 802.11b/g/n xDSL Line Driver MT7555N - MediaTek xDSL Line Driver FXS 1 ( SiLabs Si32176 Single ProSLIC ) HPNA Não Serial Sim

启动信息

DRAMC V2.0 (0)DRAMC V2.2.0.2 (0)U-Boot 1.1.5 (Dec  4 2015 - 16:36:01)CPU: MT7510Memory Size: 64 MBNAND Page size:2048B,Total size 128MB bmt pool size: 81 Using default environmentIn:    serialOut:   serialErr:   serialNet:   MTK SwitchMAC addresses in MRD and Env don't match. Use MAC in MRD: 98:97:D1:xx:xx:xx## Starting application at 0x81F00000 ...OKSearch PHY addr and found PHY addr=8Not found TC PhyHit any key to stop autoboot: 0Dual image: checking and selecting FW ......Main image is selectedUncompressing [LZMA] ...  done.Linux version 2.6.36 (victor@MSGSW1) (gcc version 4.3.4 (GCC) ) #1 SMP Fri Dec 11 18:23:42 CST 2015ISPRAM0: PA=00318000,Size=00008000,enabledDSPRAM0: PA=1dff8000,Size=00001000,enabledmemsize:64MBRalink MT751020 SOC prom initbootconsole [early0] enabledCPU revision is: 00019555 (MIPS 34Kc)Determined physical RAM map: memory: 03fe0000 @ 00020000 (usable)Wasting 1024 bytes for tracking 32 unused pagesZone PFN ranges:  Normal   0x00000020 -> 0x00004000Movable zone start PFN for each nodeearly_node_map[1] active PFN ranges    0: 0x00000020 -> 0x000040003 available secondary CPU TC(s)PERCPU: Embedded 7 pages/cpu @81083000 s7264 r8192 d13216 u65536pcpu-alloc: s7264 r8192 d13216 u65536 alloc=16*4096pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16224Kernel command line:  es=1PID hash table entries: 256 (order: -2, 1024 bytes)Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 32 bytesWriting ErrCtl register=00000808Readback ErrCtl register=00000808nmi base is 810c4200Memory: 60488k/65408k available (3076k kernel code, 4920k reserved, 646k data, 216k init, 0k highmem)SLUB: Genslabs=7, HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1Hierarchical RCU implementation.    RCU-based detection of stalled CPUs is disabled.    Verbose stalled-CPUs detection is disabled.NR_IRQS:64CPU frequency 648.00 MHz Using 266.000 MHz high precision timer.console [ttyS0] enabled, bootconsole disabledconsole [ttyS0] enabled, bootconsole disabledCalibrating delay loop... 430.89 BogoMIPS (lpj=2154496)pid_max: default: 32768 minimum: 301Mount-cache hash table entries: 51234K sync es set to 1.Config7: 0x80080500Limit of 4 TCs setTLB of 64 entry pairs shared by 2 VPEsVPE 0: TC 0 1 2, VPE 1: TC 3IPI buffer pool of 16 buffersCPU revision is: 00019555 ((null))TC 1 going on-line as CPU 1CPU revision is: 00019555 ((null))TC 2 going on-line as CPU 2CPU revision is: 00019555 ((null))TC 3 going on-line as CPU 3Brought up 4 CPUsNET: Registered protocol family 16MT7510_pcie_initcheck pcie link up status: isRC0_LINKUP=0 isRC1_LINKUP=1 registering PCI controller with io_map_base unsetbio: create slab <bio-0> at 0pci 0000:00:01.0: BAR 8: assigned [mem 0x20000000-0x200fffff]pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff]pci 0000:01:00.0: BAR 0: set to [mem 0x20000000-0x200fffff] (PCI address [0x20000000-0x200fffff]pci 0000:00:01.0: PCI bridge to [bus 01-01]pci 0000:00:01.0:   bridge window [io  disabled]pci 0000:00:01.0:   bridge window [mem 0x20000000-0x200fffff]pci 0000:00:01.0:   bridge window [mem pref disabled]PCI: Enabling device 0000:00:01.0 (0000 -> 0002)NET: Registered protocol family 8NET: Registered protocol family 20Switching to clocksource MIPSNET: Registered protocol family 2IP route cache hash table entries: 1024 (order: 0, 4096 bytes)TCP established hash table entries: 2048 (order: 2, 16384 bytes)TCP bind hash table entries: 2048 (order: 2, 16384 bytes)TCP: Hash tables configured (established 2048 bind 2048)TCP reno registeredUDP hash table entries: 128 (order: 0, 4096 bytes)UDP-Lite hash table entries: 128 (order: 0, 4096 bytes)NET: Registered protocol family 1TC3162 hardware watchdog module loaded.squashfs: version 4.0 (2009/01/31) Phillip Loughermsgmni has been set to 118cryptomgr_test used greatest stack depth: 15632 bytes leftio scheduler noop registered (default)ttyS0 at I/O 0xbfbf0003 (irq = 1) is a TC3162brd: module loadedtc3162 mtd init: mt6573_nand_init enterMediaTek MT6573 Nand driver init, version v2.0tc3162 mtd init: nandflash_probe enterAllocate 16 byte aligned buffer: 8040d1b0Enable NFI Clock# MT6573 NAND # : Use HW ECCmanu_id=c2, dev_id=f1ext_id=809502,Device found in MTK table, ID: c2f1[NAND] pagesz:2048 eccsz: 32, oobsz: 128Support this Device in MTK table! c2f1 NAND device: Manufacturer ID: 0xc2, Chip ID: 0xf1 (Unknown NAND 128MiB 3,3V 8-bit)bmt pool size: 81 Init bmt table, size: 81bmt count: 81, system count: 943begin to search BMT from block 1023 Match bmt signature @ block: 1023Valid BMT, version v1bmt found at block: 1023, mapped block: 0Load bmt data success @ block 1023 BMT v1.total 0 mappingMatch bbt signature BBT Checksum is: 0x1Valid BBT, version v1bbt found, bad block count: 0Load bbt data success [mt6573_nand] probe successfully!There is no legal FW in tclinuxCreating 14 MTD partitions on "MT6573-Nand":0x000000000000-0x000000020000 : "bootloader"0x000000020000-0x000000040000 : "romfile"0x000000040000-0x00000018808a : "Kernel_main"mtd: partition "Kernel_main" doesn't end on an erase block -- force read-only0x00000018808a-0x000000a46ef4 : "Rootfs_main"mtd: partition "Rootfs_main" doesn't start on an erase block boundary -- force read-only0x000000a26ef4-0x000000a2c6fa : "Defcfg_main"mtd: partition "Defcfg_main" doesn't start on an erase block boundary -- force read-only0x000000040000-0x000002740000 : "Tclinux_main"0x000002740000-0x000002810000 : "kernel"mtd: partition "kernel" doesn't end on an erase block -- force read-only0x000002810000-0x0000075e0000 : "rootfs"mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only0x0000075e0000-0x0000075f0000 : "defcfg"mtd: partition "defcfg" is out of reach -- disabled0x000002740000-0x000004e40000 : "tclinux"0x000004e40000-0x000007580000 : "Tclinux_Buffer"0x000007580000-0x0000075a0000 : "reservearea"0x0000075a0000-0x0000075c0000 : "romd"0x0000075c0000-0x0000075e0000 : "second_romfile"root filesystem is from Rootfs_mainPPP generic driver version 2.4.2PPP Deflate Compression module registeredPPP BSD Compression module registeredNET: Registered protocol family 24IMQ driver loaded successfully.    Hooking IMQ after NAT on PREROUTING.    Hooking IMQ before NAT on POSTROUTING.RT3xxx EHCI/OHCI init.net/core/klink_updown.c:101 >> Create link_updown kernel netlink success!u32 classifier    Performance counters on    Actions configuredNetfilter messages via NETLINK v0.30.nf_conntrack version 0.5.0 (945 buckets, 3780 max)ctnetlink v0.93: registering with nfnetlink.nf_conntrack_rtsp v0.6.21 loadingxt_time: kernel timezone is -0000GRE over IPv4 tunneling drivernf_nat_rtsp v0.6.21 loadingip_tables: (C) 2000-2006 Netfilter Core TeamTCP cubic registeredNET: Registered protocol family 10ip6_tables: (C) 2000-2006 Netfilter Core TeamIPv6 over IPv4 tunneling driverNET: Registered protocol family 17NET: Registered protocol family 15Ebtables v2.0 registered802.1Q VLAN Support v1.8 Ben Greear <[e-mail]>All bugs added by David S. Miller <[e-mail]>VFS: Mounted root (squashfs filesystem) readonly on device 31:3.Freeing unused kernel memory: 216k freedbusybox init and set affinit started:  BusyBox v1.00 (2015.12.11-10:24+0000) multi-call binary[ used greatest stack depth: 14832 bytes leftmount used greatest stack depth: 14504 bytes leftbusybox used greatest stack depth: 14168 bytes lefttcledctrl: module license 'unspecified' taints kernel.Disabling lock debugging due to kernel taintTC3162 LED Manager 0.1 inittcledctrl version: tcledctrl V1.1.0.0 (Dec 11 2015-18:24:02).insmod used greatest stack depth: 13896 bytes lefttccicmd V1.1.0.0 (Dec 11 2015-18:24:06)insmod used greatest stack depth: 13864 bytes leftsystem is initialized in normal modemin_free_kbytes=1018insmod used greatest stack depth: 13776 bytes lefttcsmux version: tcsmux V1.1.0.0 (Sep 27 2013-11:25:43).tcportbind version: tcportbind V1.1.0.0 (Dec 11 2015-18:24:08).TCSUPPORT_IPV6insmod raeth driverfemac.c:v1.00-NAPI 29.Mar.2011eth0: FE MAC Ethernet address: 98:97:D1:xx:xx:xxwrite file (/tmp/md5.txt) successfully!The number of cache node is 5Start to get customer running romfile.compressedLen = 22493compressedLen = 22493compressedLen = 22493[get_romfile_by_index]: original configuration length[84564][get_romfile_by_index]: new configuration length[84564]Get current configuration #1 successfully.Read current configuration...Start to get customer default romfile.It isn't MitraStar firmware, so can't get image version!!from Defcfg_mainData buffer not 16 bytes aligned: 8304010cData buffer not 16 bytes aligned: 8304090cData buffer not 16 bytes aligned: 8304110cData buffer not 16 bytes aligned: 8304190cData buffer not 16 bytes aligned: 8304210cData buffer not 16 bytes aligned: 8304290cData buffer not 16 bytes aligned: 8304310cData buffer not 16 bytes aligned: 8304390cData buffer not 16 bytes aligned: 8304410cData buffer not 16 bytes aligned: 8304490ccompressedLen = 22494Get current configuration successfully.Read default configuration...sslca_verify!Start to get customer default romfile.It isn't MitraStar firmware, so can't get image version!!from Defcfg_mainData buffer not 16 bytes aligned: 8305010cData buffer not 16 bytes aligned: 8305090cData buffer not 16 bytes aligned: 8305110cData buffer not 16 bytes aligned: 8305190cData buffer not 16 bytes aligned: 8305210cData buffer not 16 bytes aligned: 8305290cData buffer not 16 bytes aligned: 8305310cData buffer not 16 bytes aligned: 8305390cData buffer not 16 bytes aligned: 8305410cData buffer not 16 bytes aligned: 8305490cxDSL: xDSL down, possible reason: Not link upcompressedLen = 22494Get current configuration successfully.Read default configuration...sslca_verify![romConvert_gvt_vdsl_write]: Start romconvert[romConvert_gvt_vdsl_write]: End romconvertifconfig: br0: error fetching interface information: Device not foundFunc:dhcp6sCall_write Line:22678 ipv6_start:1 ipv6_end:ffff mrd.CountryCode = D0Success to set CountryRegion by mrd country code.mtd[readflash]:device=reservearea tclen=512 tcoffset=0Unlocking reservearea ...Reading from reservearea to /tmp/RT30xxEEPROM.bin ... hotspotService_write: hsping pid is emptytr181firewall_write Can't open /etc/isp4.confCan't open /etc/isp5.confCan't open /etc/isp6.confCan't open /etc/isp7.confCan't open /etc/isp8.confCan't open /etc/isp9.confCan't open /etc/isp4.confCan't opeAdd CWMP pass through rules.n /etc/isp5.confCan't open /etc/isp6.confCan't open /etc/isp7.confCan't open /etc/isp8.confCan't open /etc/isp9.confCan't open /etc/isp4.confCan't open /etc/isp4.confCan't open /etc/isp5.confCan't open /etc/isp5.confCan't open /etc/isp6.confCan't open /etc/isp6.confCan't open /etc/isp7.confCan't open /etc/isp7.confCan't open /etc/isp8.confCan't open /etc/isp9.confWrong interface type.Wrong interface type.Wrong interface type.Wrong interface type.Wrong interface type.Wrong interface type.Wrong application type.insmod: cannot open module `/lib/modules/tc3162l2sar.ko': No such file or directorysslca_write:get Frag Number failed!killall: dropbear: no process killeddropbear used greatest stack depth: 13616 bytes leftkillall: boa: no process killedvsProfile_write:182, getAttrValue() failedvsProfileLine_write:575, getAttrValue() failedEVENT_CFG_TOTAL_UPDATEEVENT_CFG_TOTAL_UPDATEread of forward table failed: No such deviceread of forward table failed: No such deviceread of forward table failed: No such deviceEnabling SSL security systemSSL security system enabled[01/Jan/1970:00:00:07 +0000] boa: server version Boa/0.94.13[01/Jan/1970:00:00:07 +0000] boa: server built Dec 11 2015 at 18:25:56.[01/Jan/1970:00:00:07 +0000] boa: starting server pid=198, port 80[getVoipProfileMark:2874], WanNode:  IfMarkStr:ra0       no private ioctls.read of forward table failed: No such deviceread of forward table failed: No such deviceFile /proc/tc3162/adsl_stats content Opmode is worngread of forward table failed: No such deviceread of forward table failed: No such deviceFile /proc/tc3162/adsl_stats content Opmode is worngread of forward table failed: No such deviceread of forward table failed: No such deviceFile /proc/tc3162/adsl_stats content Opmode is worng7510_debug: dmt_base_addr : bf900000ADSL DMT initialization startingBegin AdslTaskInit.....End AdslTaskInitBegin to  request IRQ 20DMT:Succeed to request IRQ 20Initializing ADSL F/W 5.6.9.0 ......read of forward table failed: No such deviceread of forward table failed: No such deviceFile /proc/tc3162/adsl_stats coInitializing ADSL F/W ........ done ntent Opmode is worngANNEXAThe test lab:60vlantag_drv_initNot support Ethernet WAN, insmod tc3162_dmt.ko!read of forward table failed: No such deviceread of forward table failed: No such deviceFile /proc/tc3162/adsl_stats content Opmode is wornginsmod: cannot insert `/lib/modules/tc3162_dmt.ko': File exists (-1): File existsTCSUPPORT_WLANTCSUPPORT_WLAN_MT7592read of forward table failed: No such deviceread of forward table failed: No such deviceFile /proc/tc3162/adsl_stats content Opmode is worngPCI: Enabling device 0000:01:00.0 (0000 -> 0002)Mirror/redirect action oneth0: starting interface.MT7510FE, PhyPart debug: tcPhyInit() in  MT7510Ge,Internal check flag: fgMT7510Ge_INT=0x0 PhyPart debug: tcPhyInit() in  read of forward table failed: No such deviceread of forward table failed: No such deviceFile /proc/tc3162/adsl_stats content Opmode is worngRalink HW NAT Module EnabledIP check use Black Listdevice eth0 entered promiscuous modeRun write_wan_mac to generate mac.confFirst get MAC address=9897D1xxxxxxFile /proc/tc3162/adsl_stats content Opmode is worngTCSUPPORT_WLAN: ifconfigefuse_probe: efuse = 10000002NVM is BIN modeCal Free IC!!tssi_1_target_pwr_g_band = 32jiffies=ffff933a, POLLING_MODE_DETECT_INTV=300ifconfig used greatest stack depth: 13560 bytes leftdevice ra0 entered promiscuous modeFile /proc/tc3162/adsl_stats content Opmode is worng##### mbss_cr_enable, BssId = 1device ra1 entered promiscuous mode##### mbss_cr_enable, BssId = 2device ra2 entered promiscuous mode##### mbss_cr_enable, BssId = 3device ra3 entered promiscuous modeTCSUPPORT_WLAN_WDSDying Gasp 0.31 initoenmap 801200 oenmap2 0TC3162 hardware watchdog initializedtelnetd: starting  port: 23; login program: /bin/loginThu Jan  1 00:00:00 UTC 2015[01/Jan/2015:00:00:00 +0000] boa.c:1019 - unable to bind: Address already in usestart upgarde_fwsh: cannot csh used greatest stack depth: 13400 bytes leftreate /proc/t========================insmod iptable_filter=======================c3162/etherwan_mode: Directory nonexistentinsmod: cannot open module `/lib/modules/2.6.36/kernel/net/ipv4/netfilter/iptable_filter.ko': No such file or directorychmod: /userfs/profile.cfg: Read-only file systemiptables: Chain already existschmod: /userfs/profile.cfg: Read-only file systemip6tables used greatest stack depth: 13080 bytes leftip6tables: No chain/target/match by that name.ip6tables: No chain/target/match by that name.ip6tables: No chain/target/match by that name.ip6tables: No chain/target/match by that name.ip6tables: No chain/target/match by that name.ip6tables: No chain/target/match by that name.ip6tables: No chain/target/match by that name.ip6tables: No chain/target/match by that name.ip6tables: No chain/target/match by that name.ip6tables: No chain/target/match by that name.ip6tables: No chain/target/match by that name.ip6tables: No chain/target/match by that name.iptables: Protocol wrong type for socketSIOCDIFADDR: Cannot assign requested addressbr0: port 2(ra0) entering forwarding statebr0: port 2(ra0) entering forwarding statebr0: port 1(eth0) entering forwarding statebr0: port 1(eth0) entering forwarding statedoneEnter set first loop, IP addr by Dhcp6sradvd startingRadvd function activated!killall: dnsmasq: no process killedOpen file OK fd=8shwarning, Failure parsing line 7 of /etc/udhcpd.conf: /userfs/bin/dproxy: not foundwarning, Failure parsing line 12 of /etc/udhcpd.confwarning, Failure parsing line 13 of /etc/udhcpd.confinfo, udhcpd (v0.9.9-pre) startedwarning, Failure parsing line 8 of /etc/udhcpd_conserpool1.confwarning, Failure parsing line 15 of /etc/udhcpd_conserpool1.confwarning, Failure parsing line 16 of /etc/udhcpd_conserpool1.confwarning, Failure parsing line 17 of /etc/udhcpd_conserpool1.confwarning, Failure parsing line 18 of /etc/udhcpd_conserpool1.confwarning, Unable to open /etc/udhcp_lease for readingread WLAN driver from rt_device failed,set with default value!killall: wscd: no process killediptables: Bad rule (does a matching rule exist in that chain?)iptables: Bad rule (does a matching rule exist in that chain?)ip6tables: Bad rule (does a matching rule exist in that chain?).ip6tables: Bad rule (does a matching rule exist in that chain?).gre_boot: Create br1 and move ra1 from br0 to br1device ra1 left promiscuous modebr0: port 3(ra1) entering disabled statedevice ra1 entered promiscuous modetr181firewall_boot iptables: Bad rule (does a matching rule exist in that chain?)chmod: /userfs/profile.cfg: Read-only file systemiptables: No chain/target/match by that nameiptables: Bad rule (does a matching rule exist in that chain?)iptables: No chain/target/match by that nameiptables: No chain/target/match by that nameiptables: No chain/target/match by that nameiptables v1.3.8: Couldn't find target `TR181FrwlInput'Try `iptables -h' or 'iptables --help' for more information.iptables v1.3.8: Couldn't find target `TR181FrwlOutput'Try `iptables -h' or 'iptables --help' for more information.iptableip used greatest stack depth: 12976 bytes lefts v1.3.8: Couldn't find target `TR181FrwlForward'Try `iptables -h' or 'iptables --help' for more information.iptables: No chain/target/match by that nameiptables: No chain/target/match by that nameiptables: No chain/target/match by that nameiptables: Bad rule (does a matching rule exist in that chain?)chmod: /userfs/profile.cfg: Read-only file systemiptables: Chain already existsiptables: Chain already existsiptables: Chain already existssh: /tmp/etc/tr181firewall_chain0.sh: not foundsh: /tmp/etc/tr181firewall_chain1.sh: not foundsh: /tmp/etc/tr181firewall_chain2.sh: not foundsh: /tmp/etc/tr181firewall_chain3.sh: not foundsh: /tmp/etc/tr181firewall_chain4.sh: not foundsh: /tmp/etc/tr181firewall_chain5.sh: not foundsh: /tmp/etc/tr181firewall_chain6.sh: not foundsh: /tmp/etc/tr181firewall_chain7.sh: not foundiptables v1.3.8: Couldn't find target `TR181_FrwlChain1Input'Try `iptables -h' or 'iptables --help' for more information.iptables v1.3.8: Couldn't find target `TR181_FrwlChain1Output'Try `iptables -h' or 'iptables --help' for more information.iptables v1.3.8: Couldn't find target `TR181_FrwlChain1Forward'Try `iptables -h' or 'iptables --help' for more information.ip6tables v1.4.10: Couldn't find target `TR181_FrwlChain1Input'Try `ip6tables -h' or 'ip6tables --help' for more information.ip6tables v1.4.10: Couldn't find target `TR181_FrwlChain1Output'Try `ip6tables -h' or 'ip6tables --help' for more information.ip6tables v1.4.10: Couldn't find target `TR181_FrwlChain1Forward'Try `ip6tables -h' or 'ip6tables --help' for more information.iptables v1.3.8: Couldn't find target `TR181_FrwlChain0Input'Try `iptables -h' or 'iptables --help' for more information.iptables v1.3.8: Couldn't find target `TR181_FrwlChain0Output'Try `iptables -h' or 'iptables --help' for more information.iptables v1.3.8: Couldn't find target `TR181_FrwlChain0Forward'Try `iptables -h' or 'iptables --help' for more information.ip6tables v1.4.10: Couldn't find target `TR181_FrwlChain0Input'Try `ip6tables -h' or 'ip6tables --help' for more information.ip6tables v1.4.10: Couldn't find target `TR181_FrwlChain0Output'Try `ip6tables -h' or 'ip6tables --help' for more information.ip6tables v1.4.10: Couldn't find target `TR181_FrwlChain0Forward'Try `ip6tables -h' or 'ip6tables --help' for more information.chmod: /userfs/profile.cfg: Read-only file systemiptables: No chain/target/match by that namechmod: /userfs/profile.cfg: Read-only file systemiptables: Chain already existsiptables: Chain already existsiptables: Chain already existsiptables: Chain already existsiptables: Chain already existsiptables: Chain already existsiptables: No chain/target/match by that nameiptables: No chain/target/match by that nameiptables: No chain/target/match by that nameiptables: No chain/target/match by that namecreate_fullnat_chain_bootEnter cwmp boot, we will start tr69 Process/etc/syslog.conf: 6: WAN-DHCP: not found/etc/syslog.conf: 7: xDSL: not found/etc/syslog.conf: 8: ETHER: not found/etc/syslog.conf: 9: PPP: not found/etc/syslog.conf: 10: SystemMainten: not found/etc/syslog.conf: 11: RemoteMGNT: not found/etc/syslog.conf: 12: TR069: not found/etc/syslog.conf: 13: NTP: not found/etc/syslog.conf: 14: DDNS: not found/etc/syslog.conf: 15: NAT: not found/etc/syslog.conf: 16: Firewall: not found/etc/syslog.conf: 17: DHCP-Srv: not found/etc/syslog.conf: 18: WLAN: not found/etc/syslog.conf: 19: INTERNET: not found/etc/syslog.conf: 20: UPNP: not found/etc/syslog.conf: 21: DoS: not found/etc/syslog.conf: 22: VoIP: not found/etc/syslog.conf: 23: IGMP: not foundinsmod: cinsmod used greatest stack depth: 12660 bytes leftannot insert `/lib/modules/hw_nat.ko': File exists (-1): File existsSegmentation faultiptables: No chain/target/match by that nameiptables: No chain/target/match by that nameiptables: No chain/target/match by that nameiptables: No chain/target/match by that nameip6tables: No chain/target/match by that name.ip6tables: No chain/target/match by that name.ip6tables: No chain/target/match by that name.ip6tables: No chain/target/match by that name.Daemon Successfully forked (pid: 3776)rmmod: xt_layer7: No such file or directory/etc/lanAlias0.confftp switch turn onsip switch turn offh323 switch turn onrtsp switch turn onl2tp switch turn on,sw_state=iptables: Bad rule (does a matching rule exist in that chain?)ipsec switch turn on,sw_state=iptables: Bad rule (does a matching rule exist in that chain?)route: SIOC[ADD|DEL]RT: File existsIt isn't MitraStar firmware, so can't get image version!!File /proc/tc3162/adsl_stats content Opmode is worngdnsroute_execute: send SIGDNSMASQ to pid=115===signal===[SignalHandle@15117] rcv sig:38 gi_BitMapForSignal:0x2.===signal===[SignalCheck@15179] iLoop:1 sig:38. Run signal handler:0x4b6a14.four portsSIOCGIFFLAGS: No such deviceinterface eth0.1 does not exist!sh: vconfig: not foundSIOCGIFFLAGS: No such deviceinterface eth0.2 does not exist!sh: vconfig: not foundSIOCGIFFLAGS: No such deviceCan't open /etc/isp8_4.confCan't open /etc/isp8_4.confCan't open /etc/isp8_5.confinterface eth0.3 does not exist!Can't open /etc/isp8_5.confsh: vconfig: not foundCan't open /etc/isp8_6.confCan't open /etc/isp8_6.confCan't open /etc/isp8_7.confCan't open /etc/isp8_7.confSIOCGIFFLAGS: No such deviceDNSROUTE: reading dns route entry 0DNSROUTE: reading dns route entry 1interface eth0.4 does not exist!sh: vconfig: not founddevice eth0 is already a member of a bridge; can't enslave it to bridge br0.File /proc/tc3162/adsl_stats content Opmode is worngAdded VLAN with VID == 1 to IF -:eth0:-WARNING:  VLAN 1 does not work with many switches,consider another number if you have problems.device eth0.1 entered promiscuous modebr0: port 3(eth0.1) entering forwarding statebr0: port 3(eth0.1) entering forwarding stateAdded VLAN with VID == 2 to IF -:eth0:-device eth0.2 entered promiscuous modebr0: port 6(eth0.2) entering forwarding statebr0: port 6(eth0.2) entering forwarding stateAdded VLAN with VID == 3 to IF -:eth0:-device eth0.3 entered promiscuous modebr0: port 7(eth0.3) entering forwarding statebr0: port 7(eth0.3) entering forwarding stateAdded VLAN with VID == 4 to IF -:eth0:-0eabcec1c08e988a3327bdc3995af6ad==>getMacEntryByIndex(): no sta existance==>getMacEntryByIndex(): no sta existance==>getMacEntryByIndex(): no sta existance==>getMacEntryByIndex(): no sta existance==>getMacEntryByIndex(): no sta existance==>getMacEntryByIndex(): no sta existance==>getMacEntryByIndex(): no sta existance==>getMacEntryByIndex(): no sta existancedevice eth0.4 entered promiscuous modebr0: port 8(eth0.4) entering forwarding statebr0: port 8(eth0.4) entering forwarding statebr0: port 1(eth0) entering forwarding statelog cicmd 0 (wan  dmt2  set  largeD  2  ) BusyBox v1.00 (2015.12.11-10:24+0000) multi-call binaryUsage: taskset [OPTIONS] [mask] [pid | command [arg]...]radvd parameter activated by exec!radvd starting<<< VoIP Init >>>File /proc/tc3162/adsl_stats content Opmode is worngPCM V2.4 (Apr 28 2015 16:50:55) init mod-slic3AddTimer: get now_time for first timeSilabs SLIC type selected by SW makefile compile option* Si32176 * deviceVerify ProSLIC_Version 7.3.2channel = 0, REG_0  = 0xa2reversion  = 0x2si32176_deviceVerify Success!DEVICE_VERIFY ret:1Init fxsNum(1) + fxoNum(0) = deviceNum(1)si32176NumProslic = 1si32176NumChannel = 1si32176deviceId = 0ProSLIC_createControlInterface = 0ProSLIC_createDevice = 0ProSLIC_createChannel = 0ProSLIC_SWInitChan = 0chanPvt[0].chanType 1chanPvt[0].chipType 6File /proc/tc3162/adsl_stats content Opmode is worngFile /proc/tc3162/adsl_stats content Opmode is worngFile /proc/tc3162/adsl_stats content Opmode is worngThreadedTimerCheck: get last for first timeFile /proc/tc3162/adsl_stats content Opmode is wornginit mod-ksocketFile /proc/tc3162/adsl_stats content Opmode is wornginit mod-acodecinit mod-foip3===============================|| MTK DSP init successfully ||===============================File /proc/tc3162/adsl_stats content Opmode is worngdbgTool_init init v2.0 File /proc/tc3162/adsl_stats content Opmode is worngpid 4125's current affinity mask: 0pid 4125's new affinity mask: 8pid 4122's current affinity mask: 0pid 4122's new affinity mask: 8pid 4146's current affinity mask: 0pid 4146's new affinity mask: 8pid 4144's current affinity mask: 0pid 4144's new affinity mask: 8pid 4145's current affinity mask: 0pid 4145's new affinity mask: 8Restarting killall: voiceApp: no process killedkillall: mm.exe: no process killedkillall: icf.exe: no process killed<<< VoIP Init Finished >>>G.inp modedoneFile /proc/tc3162/adsl_stats content Opmode is worngG.inp modedriver version: 4.0.0.8  FwVer:5.6.9.0_A_A60901 HwVer:T14.F7_0.2xDSL      module is OKWIFI      module is OKETH0      interface is OKRA0       interface is OKBR0       interface is OKAPP       tcapi is OK<<< Device is ready for use >>>ADAM Init Successslic_kpc_ioctl: cid:0 cad_num:3 DSP activated successslic_kpc_ioctl: cid:0 cad_num:3 DSP activated successDSP set event handler successDSP config country 44 successICF:Exit from function(): icf_sm_set_error_hdlr, with retval 1ICF:Exit from function(): icf_sm_process_mesg, with retval 1ICF:Entered function(): icf_mrm_recv_msgICF:Entered function(): icf_dbm_get_port_dataICF:Exit from function(): icf_dbm_get_port_data, with retval 1[ES_TRACE]:MSG received successfuly from App: 27 bytes*******================================================voiceApp:-   GET IP ADDRESS FAIL!User Agent related info = MitraStar DSL-2401HN-T1C-GV V1.14(WQR.0)b5**================================================**ICF_PRINT_HDR_DATA_START**************API_ID = 158  : ICF_SET_TRACE_REQ SOURCE_ID =107  :  DEST_ID =6  :  APP_ID =1  :CALL_ID= 65535 API_LENGTH= 27 ********voiceApp:-   GET IP ADDRESS FAIL!***ICF_PRINT_HDR_DATA_END***********ICF:Exit from function(): icf_mrm_recv_msg, with retval 1IvoiceApp:-   GET IP ADDRESS FAIL!CF:Entered function(): icf_cfg_fetch_app_confICF:Entered function(): icf_sm_process_mesgICF:EnteredvoiceApp:-   GET IP ADDRESS FAIL! fNo available interface for voice service unvoiceApp:-   GET IP ADDRESS FAIL!ction(): icf_sm_api_to_eventICF:Exit from function(): icf_sm_api_to_event, with retval 1ICF:Entered fuNo available interface for voice service ncvoiceApp:-   GET IP ADDRESS FAIL!tiNo available interface for voice service ovoiceApp:-   GET IP ADDRESS FAIL!n(No available interface for voice service ):voiceApp:-   GET IP ADDRESS FAIL! icf_sm_set_trace_req_hdlr