arm开发板烧写
来源:互联网 发布:nginx 跳转到指定ip 编辑:程序博客网 时间:2024/06/05 21:08
1.重启开发板
nter into Normal mode
Hit any key to stop autoboot: 2
显示上述信息时3s内按enter
2.进入uboot菜单
--------------------------------------------
| User Menu for GEC210 |
| |
| [f] Format the nand flash | //清空硬盘
| [s] Burn image from SD card | //烧写系统从SD卡
| [u] Use fastboot | //使用fastboot模式烧写
| [b] Boot the system | //启动系统
| [r] Reboot the u-boot | //重启u-boot
| [e] Exit to command line | //进入命令行模式
--------------------------------------------
3.按u进入fastboot模式
若提示Insert a OTG cable into the connector!
则需要安装驱动(若已安装好驱动,则跳过该步骤)
(安装驱动,驱动安装完毕后应该格式化硬盘)
装完驱动后按ctrl+c退出fastboot模式
4.按f格式化硬盘
Really screb this NAND flash? <y/n>
按y(不会显示y)再按enter
(注意格式化硬盘后千万不能断电或者重启)
显示如下信息:
Erasing at 0x3ffe0000 -- 100% complete.
Scanning device for bad blocks
则清空完毕。
5.再按u
再次进入fastboot模式,进行系统的烧写。
点击auto.bat烧写脚本(注意查看脚本中的内容)
fastboot.exe flash uboot uboot.bin
fastboot.exe flash kernel uImage
fastboot.exe flash system rootfs.img
#fastboot.exe -w
以上内容都必须有对应的文件,如要有uboot.bin文件
显示如下内容重启开发板即可:
Writing data at 0x74b6800 -- 100% complete.
111070080 bytes written: OK
partition 'system' flashed
粤嵌开发板屏幕校正
/tslib/bin/ts_calibrate
阅读全文
0 0
- arm开发板烧写
- arm开发
- s3c6410 ARM开发板烧写uboot新手入门笔记
- ARM开发板烧写linux系统的步骤
- s3c6410 ARM开发板烧写uboot新手入门笔记
- 学习ARM开发(1)
- 学习ARM开发(2)
- 学习ARM开发(3)
- 学习ARM开发(4)
- 学习ARM开发(5)
- 学习ARM开发(6)
- 学习ARM开发(7)
- 学习ARM开发(8)
- 学习ARM开发(9)
- 学习ARM开发(10)
- 学习ARM开发(11)
- ARM的开发步骤
- 学习ARM开发(12)
- 虚幻4中实现简单的raymarch
- 去掉字符串中空格的四种方法
- 徽章系列3: Travis CI 的使用
- SQL左右连接中的on and和on where的区别
- 数学分析
- arm开发板烧写
- 面向对象_基本概念(2)
- 徽章系列8:生成个性徽章
- linux系统网络配置
- Qt 常用类(3)—— QString
- 徽章系列4: Circle CI 的使用
- 外观设计模式
- 24.Android-实现黑名单电话拦截
- POJ 3111 K Best(二分——最大化平均值)