QR 解码解析
来源:互联网 发布:jsp 企业站cms 编辑:程序博客网 时间:2024/06/14 04:06
It's not hard to decode QR codes with a pen and paper. For this guide I'm going to grab a random QR code from google images and show the process of decoding it by hand. QR codes contain a lot of error correction information and they can survive a lot of errors, but that's a lot harder to do using just a pen and paper (and 99% of the QR codes you encounter don't have any missing bits, so it's rarely necessary). So I'll highlight where the error correction information is stored, but I won't explain it in this guide.
The picture I found is from http://mikejcaruso.blogspot.ca/2011/04/qr-code-tattoos.html
Before we begin we should rotate it to the proper orientation. QR codes always have 3 timing patterns (big black squares) in all the corners except for the bottom-right. So we need to rotate our picture 90 degrees counterclockwise:
The first thing we should learn is what QR code version we're looking at. The version basically just represents the physical size of the QR code. Count the number of pixels (or modules) across the QR code, subtract 17, and divide by 4. For example, our tattoo QR code is 25 modules wide, and (25-17)/4 = 2, which means this is a version 2 QR code. Very big QR codes (versions 7-40) have a few extra features, but most consumer QR codes are fairly small and simple, so you don't need to worry about that.
Next, we will figure out our QR code's format marker. Every QR code stores two identical copies of the format marker, but we only need one of them. The format marker is 15 bits long: 5 bits of format information, and 10 bits for error correction. The first 5 bits of the format marker hold the error correction level (2 bits) and the data mask (3 bits). These 5 bits are found here:
So in our case the format information is 01100. However this number has been XOR'ed with 10101 before being written into the QR code. So we must flip bits 1, 3 and 5. After flipping the bits, we get a format information string of 01100^10101 = 11001. The first two bits of this value are the error correction level (the amount of error correction data included in the QR code). Again, we can ignore this. The last 3 bits of the format string are 001, and this is the most important piece of information. This means the body of the QR code has been masked against the mask number 001. Here is a table of all the possible mask numbers and their appearance:
Here's where you need the pen and paper. The reason QR codes are masked in the first place is that sometimes particular combinations of data bytes produce QR codes with certain undesirable features (like big empty blocks in the middle). These undesirable features confuse the QR code reader, so the data is masked against a value in order to make the code easier to process when it's scanned by a QR code reader. The computer then unmasks the original data bytes using the same process, and retrieves the data.
You can imagine the masking process as essentially covering the surface of the QR code in one of the patterns seen above, starting from the top left corner. In our case we have a mask reference number 001, which means all of the odd-numbered rows are black. Once we've tiled the surface of our original QR code using the mask pattern, then every black pixel in the mask means we need to invert the corresponding bit in the original QR code. So in our case, we need to (in our mind, or using the pen and paper) invert all of the bits on odd-numbered rows. Note that we only mask the data pixels, and not the timing patterns or the format marker (otherwise we wouldn't know how to unmask it to get the mask reference number!). The data areas are the yellow areas in this picture:
I've highlighted the data areas of the tattoo QR code below:
Note that there's a little island in the middle of the data area that we must work around. That's called an alignment pattern, and whenever you see one in the data just skip past it to read the data bytes.
From now on we need to always remember the mask pattern above, and whenever we read bits from the data section we need to account for the mask pattern, and flip any bits that would be masked off by it (in our case, that's every odd row).
The data section consists of [header][data] chunks. Technically QR codes are allowed to have several of these chunks, but most QR codes just have one big chunk that holds all the data, so it won't matter. The header has an encoding type and a length (the number of data bytes). The encoding type is always 4 bits, but the length is stored in 8-10 bits depending on the encoding type. Here's the encoding type of our tattoo:
But remember, every odd row needs to have its bits inverted. To help us remember, I'll use green to highlight every cell that should be inverted when we read it:
Now, the encoding type is stored as the bottom-right 4 bits, starting from the bottom right and working left and right in a zig-zag motion.
So in our case, the tattoo itself has the bits 1000. However the bottom row is masked, so we invert the first two bits: 0100. This means that our QR code's encoding type is 0100. Here's the table of encoding types:
- 0001 Numeric
- 0010 Alphanumeric
- 0100 8-bit Byte
The other encoding types are rarely used in consumer QR codes. They're used for encoding japanese characters, custom charsets and spreading a message across several QR codes in series. For our purposes these 3 encodings will be enough.
So that means that our QR code uses 8-bit byte encoding. The next piece of information is the length field, or the number of characters (clusters of bits) that are in the message. Like I said, the length field changes size depending on the encoding type. Here's the number of bits in the length field, for each encoding type:
- Numeric (10 bits)
- Alphanumeric (9 bits)
- 8-bit Byte (8 bits)
Since we're using 8-bit byte mode, our length field is 8 bits long. We read the next 8 bits in a vertical zig-zag motion, like this:
So the tattoo itself contains the bits 11011100 (reading from bottom to top). However we need to mask two of these rows, so the actual length field has the value 00010000. That's 16 in decimal, which means this QR code has a message that is sixteen 8-bit bytes long. After the length field, the bytes themselves are stored, one after another, MSB first. We continue climbing in a vertical zig-zag motion until we hit the top, and then we curl over and continue downwards as seen in this picture:
So the first byte would be 10000110 (masked), which is 01001101 (unmasked). That corresponds to ASCII character 'M'. The next byte would be 10101101 (masked), which is 01100001 (unmasked). That corresponds to ASCII character 'a'. So far we've decoded "Ma".
Continuing up and around the corner: 10100000 (masked), or 01100011 (unmasked). That's ASCII 'c'. Then it's 'i'.
By continuing in this way, we can decode the full message: Maci Clare Peltz.
- heavyw8t
- qartis
- Raymond Decelles
- Luke
- qartis
- Les Potter
- Les Potter
- qartis
- qartis
- Martie Anderson
- qartis
- Martie Anderson
- 刘文景
- Iri
- Felfa
- Iri
- PointyOintment
- kamrom dechu
- Ninan Naner
- David Konsumer
- Ninan Naner
- Edmund French
- cal soderberg
- Dennis Danne
- QR 解码解析
- QR code 解码/编码 没有那么神奇
- 二维条码 QR code 的解码
- QR二维码编码解码原理算法介绍
- QR码创建过程解析
- 开源二维码QR CODE编码/解码(识别)库
- WINCE WM 下QR, DM, PDF417 二维码解码库
- 二维码QR Code简介及其解码实现(zxing-cpp)
- 摄像头拍照及解析QR二维码
- Atitit zxing二维码qr码识别解析
- 使用zxing生成与解析qr二维码
- 手机编码解码解析
- 红外编解码解析
- java 生成QR二维码 解析二维码 以及完整实例
- 基于Google的zxing生成和解析QR Code
- 新增基于Client、Server架构的远程QR二维码编解码系统
- HEVC解码中的SPS解析
- HEVC解码中的SPS解析
- 【poj 3268】 Silver Cow Party 【USACO 2007 February Silver】
- idea快捷键
- 面试那些事儿- UI设计面试常见问题
- The Tweak File
- 史上最简单的 SpringCloud 教程 | 第一篇: 服务的注册与发现(Eureka)
- QR 解码解析
- 8、XML 学习记录——语法、元素、属性
- 2017云栖大会·杭州峰会:《在线用户行为分析:基于流式计算的数据处理及应用》实验环境准备
- Java爬虫,爬取竞彩网数据并按指定格式输出到excel表格中
- JDK8中ThreadGroup源码解析
- bzoj 1679: [Usaco2005 Jan]Moo Volume 牛的呼声 乱搞
- SpringMVC与Struts2区别与比较总结
- Servlet学习笔记 设置缓冲区的大小及标头
- json使用问题