树莓派3 配置文件conf 高分辨率 串口引脚重映射
来源:互联网 发布:燕山大学网络教育平台 编辑:程序博客网 时间:2024/05/21 08:42
# For more options and information see
# http://rpf.io/configtxtreadme
# Some settings may impact device functionality. See link above for details
# uncomment if you get no picture on HDMI for a default "safe" mode
#hdmi_safe=1
# uncomment this if your display has a black border of unused pixels visible
# and your display can output without overscan
#disable_overscan=1
# uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16
# uncomment to force a console size. By default it will be display's size minus
# overscan.
#framebuffer_width=1280
#framebuffer_height=720
# uncomment if hdmi display is not detected and composite is being output
hdmi_force_hotplug=1
# uncomment to force a specific HDMI mode (this will force VGA)
hdmi_group=2
hdmi_mode=23
# uncomment to force a specific HDMI mode (this will force VGA)
#hdmi_group=1
#hdmi_mode=1
# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
#hdmi_drive=2
# uncomment to increase signal to HDMI, if you have interference, blanking, or
# no display
#config_hdmi_boost=4
# uncomment for composite PAL
#sdtv_mode=2
#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800
# Uncomment some or all of these to enable the optional hardware interfaces
dtparam=i2c_arm=on
#dtparam=i2s=on
dtparam=spi=on
# Uncomment this to enable the lirc-rpi module
#dtoverlay=lirc-rpi
# Additional overlays and parameters are documented /boot/overlays/README
# Enable audio (loads snd_bcm2835)
dtparam=audio=on
start_x=1
gpu_mem=128
#enable_uart=0
dtoverlay=pi3-miniuart-bt
force_turbo=1
# http://rpf.io/configtxtreadme
# Some settings may impact device functionality. See link above for details
# uncomment if you get no picture on HDMI for a default "safe" mode
#hdmi_safe=1
# uncomment this if your display has a black border of unused pixels visible
# and your display can output without overscan
#disable_overscan=1
# uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16
# uncomment to force a console size. By default it will be display's size minus
# overscan.
#framebuffer_width=1280
#framebuffer_height=720
# uncomment if hdmi display is not detected and composite is being output
hdmi_force_hotplug=1
# uncomment to force a specific HDMI mode (this will force VGA)
hdmi_group=2
hdmi_mode=23
# uncomment to force a specific HDMI mode (this will force VGA)
#hdmi_group=1
#hdmi_mode=1
# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
#hdmi_drive=2
# uncomment to increase signal to HDMI, if you have interference, blanking, or
# no display
#config_hdmi_boost=4
# uncomment for composite PAL
#sdtv_mode=2
#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800
# Uncomment some or all of these to enable the optional hardware interfaces
dtparam=i2c_arm=on
#dtparam=i2s=on
dtparam=spi=on
# Uncomment this to enable the lirc-rpi module
#dtoverlay=lirc-rpi
# Additional overlays and parameters are documented /boot/overlays/README
# Enable audio (loads snd_bcm2835)
dtparam=audio=on
start_x=1
gpu_mem=128
#enable_uart=0
dtoverlay=pi3-miniuart-bt
force_turbo=1
阅读全文
0 0
- 树莓派3 配置文件conf 高分辨率 串口引脚重映射
- PWM输出引脚重映射
- 关于STM32的引脚重映射
- 串口引脚
- STM32的功能引脚重映射和复用功能
- STM32的功能引脚重映射和复用功能
- stm32f40x reference manual 找不到引脚重映射的介绍
- stm32端口“重映射” &&串口学习
- stm32f103串口实现重映射功能
- 树莓派samba smb.conf配置文件
- 并串口引脚定义
- 串口并口引脚定义
- 串口DB9引脚图
- 串口引脚的标识
- DB9串口引脚定义
- DB9串口引脚定义
- DB9串口引脚定义
- 引脚配置文件gpiomux
- 蒙特.卡罗方法求解圆周率近似值原理与Python实现
- Android Studio 快捷键
- 排序算法摘要
- spring基础
- 10:找最大数序列
- 树莓派3 配置文件conf 高分辨率 串口引脚重映射
- java面试题
- Android 设置控件阴影的三种方式
- 神级好文,亲测有效-入门Webpack,看这篇就够了
- 音乐自动切换和轮播
- Android获取手机唯一标识
- Minmum Depth of Binary Tree
- 谁是真凶?《CSI:犯罪现场调查》正帮助AI提高断案能力
- Uber开源深度概率编程语言Pyro,AI实验室蛰伏一年首现身