ISim P.20131013 (signature 0x7708f090)
来源:互联网 发布:淘宝促销免费模板 编辑:程序博客网 时间:2024/06/07 02:29
ISim P.20131013 (signature 0x7708f090)
This is a Full version of ISim.
WARNING: File "F:/workspace/FPGA/xilinx/DDR3/tsb.v" Line 35. For instance tsb/uut/, width 12 of formal port sys_addr is not equal to width 16 of actual variable sys_addr.
WARNING: File "F:/workspace/FPGA/xilinx/DDR3/tsb.v" Line 41. For instance tsb/uut/, width 14 of formal port mcb5_dram_a is not equal to width 13 of actual signal mcb5_dram_a.
WARNING: File "F:/workspace/FPGA/xilinx/DDR3/tsb.v" Line 53. For instance tsb/uut/, width 14 of formal port mcb1_dram_a is not equal to width 13 of actual signal mcb1_dram_a.
Time resolution is 1 ps
Simulator is doing circuit initialization process.
ERROR: In process DDR_WR_FSM.vCont_96_11
FATAL ERROR:ISim: This application has discovered an exceptional condition from which it cannot recover. Process will terminate. To search for possible resolutions to this issue, refer to the Xilinx answer database by going to http://www.xilinx.com/support/answers/index.htm and search with keywords 'ISim' and 'FATAL ERROR'. For technical support on this issue, please open a WebCase with this project attached at http://www.xilinx.com/support.
INFO: Simulator is stopped.
ISim>
解决方案
Solution 1
This error can occur if there were syntax errors or problems while running the simulator executable. For more details, review the ISim log (isim.log) available in the project directory (or working directory, if launching simulation in batch mode).
This issue is currently under investigation to better address this condition in a future release of the ISE Simulator.
If the information contained in the log file does not help you address the problem, open a WebCase with Xilinx Technical Support for further assistance: http://www.xilinx.com/support/clearexpress/websupport.htm
Solution 2
This error can also occur if the simulator engine cannot allocate sufficient memory during elaboration of a large design. This is particularly applicable to Post-Route simulations due to the large structural netlist and timing back-annotation. Additionally, this issue occurs mostly on Windows 32-bit machines as the 32-bit kernel can only allocate 2 GB per process; refer to (Xilinx Answer 14932).
To resolve this issue:
Run the simulation on a Linux 32-bit system; as the Linux 32-bit kernel can allocate up to 4 GB of memory.
Run the simulation on a supported 64-bit system. For a list of supported 64-bit simulators, refer to http://www.xilinx.com/ise/ossupport/.
Follow the instructions in (Xilinx Answer 14932) to enable 3 GB application support (Windows XP only).
This issue is currently under investigation to better address this condition in a future release of the ISE Simulator.
原因是直接跑Simulation但是存在综合语法问题,只要跑一遍Implementation就可以找到错误了
This is a Full version of ISim.
WARNING: File "F:/workspace/FPGA/xilinx/DDR3/tsb.v" Line 35. For instance tsb/uut/, width 12 of formal port sys_addr is not equal to width 16 of actual variable sys_addr.
WARNING: File "F:/workspace/FPGA/xilinx/DDR3/tsb.v" Line 41. For instance tsb/uut/, width 14 of formal port mcb5_dram_a is not equal to width 13 of actual signal mcb5_dram_a.
WARNING: File "F:/workspace/FPGA/xilinx/DDR3/tsb.v" Line 53. For instance tsb/uut/, width 14 of formal port mcb1_dram_a is not equal to width 13 of actual signal mcb1_dram_a.
Time resolution is 1 ps
Simulator is doing circuit initialization process.
ERROR: In process DDR_WR_FSM.vCont_96_11
FATAL ERROR:ISim: This application has discovered an exceptional condition from which it cannot recover. Process will terminate. To search for possible resolutions to this issue, refer to the Xilinx answer database by going to http://www.xilinx.com/support/answers/index.htm and search with keywords 'ISim' and 'FATAL ERROR'. For technical support on this issue, please open a WebCase with this project attached at http://www.xilinx.com/support.
INFO: Simulator is stopped.
ISim>
解决方案
Solution 1
This error can occur if there were syntax errors or problems while running the simulator executable. For more details, review the ISim log (isim.log) available in the project directory (or working directory, if launching simulation in batch mode).
This issue is currently under investigation to better address this condition in a future release of the ISE Simulator.
If the information contained in the log file does not help you address the problem, open a WebCase with Xilinx Technical Support for further assistance: http://www.xilinx.com/support/clearexpress/websupport.htm
Solution 2
This error can also occur if the simulator engine cannot allocate sufficient memory during elaboration of a large design. This is particularly applicable to Post-Route simulations due to the large structural netlist and timing back-annotation. Additionally, this issue occurs mostly on Windows 32-bit machines as the 32-bit kernel can only allocate 2 GB per process; refer to (Xilinx Answer 14932).
To resolve this issue:
Run the simulation on a Linux 32-bit system; as the Linux 32-bit kernel can allocate up to 4 GB of memory.
Run the simulation on a supported 64-bit system. For a list of supported 64-bit simulators, refer to http://www.xilinx.com/ise/ossupport/.
Follow the instructions in (Xilinx Answer 14932) to enable 3 GB application support (Windows XP only).
This issue is currently under investigation to better address this condition in a future release of the ISE Simulator.
原因是直接跑Simulation但是存在综合语法问题,只要跑一遍Implementation就可以找到错误了
阅读全文
0 0
- ISim P.20131013 (signature 0x7708f090)
- ISim技巧
- error signature Event Type:clr20r3 P1: P2:...P:9
- Signature
- ISim使用技巧
- rom isim仿真
- 【转】isim使用技巧
- Isim仿真使用手册
- 使用Signature Tool自动生成P/Invoke调用Windows API的C#函数声明
- 使用Signature Tool自动生成P/Invoke调用Windows API的C#函数声明
- 使用Signature Tool自动生成P/Invoke调用Windows API的C#函数声明
- 使用Signature Tool自动生成P/Invoke调用Windows API的C#函数声明
- 使用Signature Tool自动生成P/Invoke调用Windows API的C#函数声明
- 使用Signature Tool自动生成P/Invoke调用Windows API的C#函数声明
- 使用Signature Tool自动生成P/Invoke调用Windows API的C#函数声明
- 使用Signature Tool自动生成P/Invoke调用Windows API的C#函数声明
- 使用Signature Tool自动生成P/Invoke调用Windows API的C#函数声明
- 使用Signature Tool自动生成P/Invoke调用Windows API的C#函数声明
- Eclipse 快捷键
- jsonp简单小demo
- 算法练习——第一天
- 第一次完成FFmepg的移植,编译ffmpeg4Android
- 聊天机器人(chatbot)终极指南:自然语言处理(NLP)和深度机器学习(Deep Machine Learning)
- ISim P.20131013 (signature 0x7708f090)
- 改无序单链表为有序
- 12.1作业
- TensorFlow 学习
- 整数分解
- 将输入的字符串反序打印。例如输入“I am a student.”输出“student. a am I”。
- Echart 饼图背景颜色设置
- BOM的学习(1)
- 立方变自身