Cisco 交换机设置Port Channel 分享
来源:互联网 发布:淘宝批量删除宝贝软件 编辑:程序博客网 时间:2024/05/02 04:24
该方式下, 首先将L2与L3的内部接口作成以太通道,然后,在L3上创建一个虚拟的通道接口,在该接口下开子接口为各个VLAN提供三层路由功能。
在广西城域网工程中,所有的4006交换机都是采用的这种方式。关于以太通道的介绍见上文。
配置步骤:(以下假设L3模去是插在第二槽上,且使用缺省的channel协议)
① L2:set port channel mod/ports 配置GE端口。
Cat4000> (enable) set port channel 2/1-2 mode on
Ports 2/1-2 channel mode set to on.
Cat4000> (enable)
②指定同一channel的端口为相同VLAN。
Cat4000> (enable) set vlan 1 2/1-2 <---端口2/1-2必须属于同一VLAN
VLAN Mod/Ports
---- -----------------------
1 2/1-4,2/6-48
3/1-6
Cat4000> (enable)
③用 set trunk mod_num/port_num 打开Trunk功能并且指定封装类型
Cat4000> (enable) set trunk 2/1 on dot1Q 1-10 <----只需要在其中一个端口指定trunk即可
Port(s) 2/1 trunk mode set to on
Port(s) 2/1 trunk type set to dot1Q 1-10
Cat4000> (enable)
④利用 session mod_num 进入L3模块
Cat4000> (enable) session 2
Trying Router...
Connected to Router.
Escape character is /Q^]'.
router>
⑤创建 EtherChannel (portchannel)接口,接口范围为1 到 64:
router(config)# interface port-channel channel_number
⑥将GE3和GE4端口绑到portchannel上。
router(config)# interface g3
router(config-if)# channel-group channel_number
router(config-if)# exit
router(config)# interface g4
router(config-if)# channel-group channel_number
router(config-if)# exit
⑦创建子接口和封装VLAN。
router(config)# interface port-channel channel_number.vlan_id
router(config-subif)# encapsulation dot1Q vlan_id
router(config-subif)# ip address ip_address subnet_mask
router(config-subif)# exit
重复以上步骤直到将所有的VLAN都封装完毕。
⑧ 利用 native关键字封装一个本地VLAN的子接口。需要为Trunk干道来产生一个本地VLAN子接口。注意,该native要求与L2的native vlan号相同
router(config)# interface port-channel channel_number.vlan_id
router(config-subif)# encapsulation dot1Q vlan_id native
<-------native指明此接口为本地VLAN接口
router(config-subif)# ip address ip_address subnet_mask
router(config-subif)# exit
以下是该方式的一个完整示例:
L2:(采用PAgP协议)
Set vlan 1 2/1-2
set port channel 2/1-2 mode on
set trunk 2/1 on dot1q 1-1005
set trunk 2/2 on dot1q 1-1005
L3:
version 12.0
no service pad
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
!
hostname M-4006R-NN
!
boot system flash bootflash:cat4232-in-mz.120-18.W5.22b.bin
enable secret 5
!
interface Loopback0
ip address
no ip directed-broadcast
!
interface Port-channel1
no ip address
no ip directed-broadcast
hold-queue 300 in
!
interface Port-channel1.1
description manage-vlan
encapsulation dot1Q 1 native
no ip directed-broadcast
!
interface Port-channel1.2
description local Management
encapsulation dot1Q 2
no ip directed-broadcast
!
interface Port-channel1.76
description uplink to
encapsulation dot1Q 76
ip address XXXX
no ip directed-broadcast
!
interface Port-channel1.201
description PPPoE test 2002.8.1
encapsulation dot1Q 201
ip address 192.168.1.2 255.255.255.0
no ip directed-broadcast
!
interface FastEthernet1
no ip address
no ip directed-broadcast
shutdown
!
interface GigabitEthernet1
no ip address
no ip directed-broadcast
shutdown
!
interface GigabitEthernet2
no ip address
no ip directed-broadcast
shutdown
!
interface GigabitEthernet3
no ip address
no ip directed-broadcast
no negotiation auto
channel-group 1
!
interface GigabitEthernet4
no ip address
no ip directed-broadcast
no negotiation auto
channel-group 1
!
ip classless
ip route 0.0.0.0 0.0.0.0
- Cisco 交换机设置Port Channel 分享
- 设置port-channel cisco 35
- 交换机通过port-channel互联
- Cisco交换机设置点滴
- CISCO 交换机 SPAN设置
- CIsco交换机恢复出厂设置
- 交换机端口捆绑配置方法(port-channel配置)
- 交换机端口捆绑配置方法(port-channel配置)
- Cisco交换机端口广播风暴设置
- cisco交换机设置口令及用户
- Cisco三层交换机端口设置trunk方法
- cisco交换机
- Port Channel 介绍
- Cisco port Disable
- Syslog 日志服务器用来获取交换机日志CISCO和H3C交换机的设置
- 交换机port-security配置
- Cisco交换机命令清单
- CISCO 交换机 DHCP 管理
- cvs update: move away src *****; it is in the way
- 什么是TTY?[今天算是明白了]
- RHEL5升级linux内核到2.6.27
- 最后的精灵:三位诺贝尔文学奖得主盛赞的生命寓言
- 学习Java从什么地方开始学
- Cisco 交换机设置Port Channel 分享
- Gridview选中Checkbox后删除选中记录
- 实训资料
- JProfiler.v4.2.2+注册机
- 图象伽玛值
- Symbian设置CEikEdwin字体
- 如何创建robots.txt文件
- JS获取当前时间并计算时间差
- [健康小常识]有化妆习惯女性夏季更易招致蚊子叮咬