Cisco Router and switch 配置命令(八)
来源:互联网 发布:怎么打理淘宝加盟店 编辑:程序博客网 时间:2024/06/05 09:06
1.在基于IOS的交换机上设置主机名/系统名:
switch(config)# hostname hostname
在基于CLI的交换机上设置主机名/系统名:
switch(enable) set system name name-string
2.在基于IOS的交换机上设置登录口令:
switch(config)# enable password level 1 password
在基于CLI的交换机上设置登录口令:
switch(enable) set password
switch(enable) set enalbepass
3.在基于IOS的交换机上设置远程访问:
switch(config)# interface vlan 1
switch(config-if)# ip address ip-address netmask
switch(config-if)# ip default-gateway ip-address
在基于CLI的交换机上设置远程访问:
switch(enable) set interface sc0 ip-address netmask broadcast-address
switch(enable) set interface sc0 vlan
switch(enable) set ip route default gateway
4.在基于IOS的交换机上启用和浏览CDP信息:
switch(config-if)# cdp enable
switch(config-if)# no cdp enable
为了查看Cisco邻接设备的CDP通告信息:
switch# show cdp interface [type modle/port]
switch# show cdp neighbors [type module/port] [detail]
在基于CLI的交换机上启用和浏览CDP信息:
switch(enable) set cdp {enable|disable} module/port
为了查看Cisco邻接设备的CDP通告信息:
switch(enable) show cdp neighbors[module/port] [vlan|duplex|capabilities|detail]
5.基于IOS的交换机的端口描述:
switch(config-if)# de脚本ion de脚本ion-string
基于CLI的交换机的端口描述:
switch(enable)set port name module/number de脚本ion-string
6.在基于IOS的交换机上设置端口速度:
switch(config-if)# speed{10|100|auto}
在基于CLI的交换机上设置端口速度:
switch(enable) set port speed moudle/number {10|100|auto}
switch(enable) set port speed moudle/number {4|16|auto}
7.在基于IOS的交换机上设置以太网的链路模式:
switch(config-if)# duplex {auto|full|half}
在基于CLI的交换机上设置以太网的链路模式:
switch(enable) set port duplex module/number {full|half}
8.在基于IOS的交换机上配置静态VLAN:
switch# vlan database
switch(vlan)# vlan vlan-num name vla
switch(vlan)# exit
switch# configure teriminal
switch(config)# interface interface module/number
switch(config-if)# switchport mode access
switch(config-if)# switchport access vlan vlan-num
switch(config-if)# end
在基于CLI的交换机上配置静态VLAN:
switch(enable) set vlan vlan-num [name name]
switch(enable) set vlan vlan-num mod-num/port-list
9. 在基于IOS的交换机上配置VLAN中继线:
switch(config)# interface interface mod/port
switch(config-if)# switchport mode trunk
switch(config-if)# switchport trunk encapsulation {isl|dotlq}
switch(config-if)# switchport trunk allowed vlan remove vlan-list
switch(config-if)# switchport trunk allowed vlan add vlan-list
在基于CLI的交换机上配置VLAN中继线:
switch(enable) set trunk module/port [on|off|desirable|auto|nonegotiate]
Vlan-range [isl|dotlq|dotl0|lane|negotiate]
10.在基于IOS的交换机上配置VTP管理域:
switch# vlan database
switch(vlan)# vtp domain domain-name
在基于CLI的交换机上配置VTP管理域:
switch(enable) set vtp [domain domain-name]
11.在基于IOS的交换机上配置VTP 模式:
switch# vlan database
switch(vlan)# vtp domain domain-name
switch(vlan)# vtp {sever|cilent|transparent}
switch(vlan)# vtp password password
在基于CLI的交换机上配置VTP 模式:
switch(enable) set vtp [domain domain-name] [mode{ sever|cilent|transparent }][password password]
12. 在基于IOS的交换机上配置VTP版本:
switch# vlan database
switch(vlan)# vtp v2-mode
在基于CLI的交换机上配置VTP版本:
switch(enable) set vtp v2 enable
13. 在基于IOS的交换机上启动VTP剪裁:
switch# vlan database
switch(vlan)# vtp pruning
在基于CL I 的交换机上启动VTP剪裁:
switch(enable) set vtp pruning enable
14.在基于IOS的交换机上配置以太信道:
switch(config-if)# port group group-number [distribution {source|destination}]
在基于CLI的交换机上配置以太信道:
switch(enable) set port channel moudle/port-range mode{on|off|desirable|auto}
15.在基于IOS的交换机上调整根路径成本:
switch(config-if)# spanning-tree [vlan vlan-list] cost cost
在基于CLI的交换机上调整根路径成本:
switch(enable) set spantree portcost moudle/port cost
switch(enable) set spantree portvlancost moudle/port [cost cost][vlan-list]
16.在基于IOS的交换机上调整端口ID:
switch(config-if)# spanning-tree[vlan vlan-list]port-priority port-priority
在基于CLI的交换机上调整端口ID:
switch(enable) set spantree portpri {mldule/port}priority
switch(enable) set spantree portvlanpri {module/port}priority [vlans]
- Cisco Router and switch 配置命令(八)
- Cisco Router and switch 配置命令(一)
- Cisco Router and switch 配置命令(二)
- Cisco Router and switch 配置命令(三)
- Cisco Router and switch 配置命令(四)
- Cisco Router and switch 配置命令(五)
- Cisco Router and switch 配置命令(六)
- Cisco Router and switch 配置命令(七)
- Cisco Router and switch 配置命令(九)
- Cisco Router and switch 配置命令(十)
- Cisco Router and switch 配置命令(十一)
- CISCO SWITCH &ROUTER基本配置命令
- Router and switch 配置命令精华压缩版
- Router and switch 配置命令精华压缩版
- Cisco's router and switch : Encryption and Crack
- cisco router 配置SDM
- CISCO router基本配置
- cisco switch命令大全
- Diamond
- 汉字的一些关注点,Microsoft Visual Studio International Feature Pack 2.0 数值到大写的转化,汉字翻译成日文韩文,文本框内容的对其,etc
- 使用VC获取字符串的长度
- TC++PL Chapter 4 读书笔记
- JS代码大全
- Cisco Router and switch 配置命令(八)
- Java代码优化,策略与方法
- 《软件园里的流氓》更新通知
- java 日期 格式
- java class classes文件路径
- Oracle数据库游标使用大全
- System.getProperty()参数大全
- Tomcat 下生癖字显示成乱码的问题
- 网页基础学习