使用PLC的自动化制造系统2.1
来源:互联网 发布:ubuntu中文语言包 编辑:程序博客网 时间:2024/04/30 06:28
2.1 INTRODUCTION
2.1简介
Control engineering has evolved over time. In the past humans were the main method for controlling a system. More recently electricity has been used for control and early electrical control was based on relays. These relays allow power to be switched on and off without a mechanical switch. It is common to use relays to make simple logical control decisions. The development of low cost computer has brought the most recent revolution, the Programmable Logic Controller (PLC). The advent of the PLC began in the 1970s, and has become the most common choice for manufacturing controls.
PLCs have been gaining popularity on the factory floor and will probably remain predominant for some time to come. Most of this is because of the advantages they offer.
• Cost effective for controlling complex systems.
• Flexible and can be reapplied to control other systems quickly and easily.
• Computational abilities allow more sophisticated control.
• Trouble shooting aids make programming easier and reduce downtime.
• Reliable components make these likely to operate for years before failure.
控制工程与时俱进。在过去,人力是实现施控系统的主要方法。最近电力已用于控制,早期电气控制是基于继电器的。这些继电器可以不借助于机械开关而使电源切断或接通。这是使用继电器实现简单的逻辑控制的通常用法的结果。低成本电脑的发展带来了最新的革命——可编程逻辑控制器( PLC )。PLC的出现开始于20世纪70年代,已成为制造控制最常见的选择。
PLC在越来越多的工厂车间里流行,并可能继续在今后一段时间内占主导地位。这其中大部分原因是因为他们所提供的优势。
•控制复杂系统成本显著。
•灵活,可快捷方便地再应用到其他控制系统。
•计算能力允许更精密的控制。
•故障排除手段使编程更容易,减少停机时间。
•可靠的部件,使这些部件在失效前可能运行几年。
- 使用PLC的自动化制造系统2.1
- 使用PLC的自动化制造系统
- 使用PLC的自动化制造系统2.1.1 Ladder Logic
- 使用PLC的自动化制造系统——2.1.3 PLC的连接
- 使用PLC的自动化制造系统——3.3继电器
- 使用PLC的自动化制造系统——个案研究
- 使用PLC的自动化制造系统——2.1.2 编程
- 使用PLC的自动化制造系统——2.1.4 梯形逻辑输入
- 使用PLC的自动化制造系统——2.1.5梯形逻辑输出
- 使用PLC的自动化制造系统——3、PLC硬件
- 使用PLC的自动化制造系统——2.2案例研究
- 使用PLC的自动化制造系统——3.2输入和输出
- 使用PLC的自动化制造系统——3.2.1 Inputs
- 使用PLC的自动化制造系统——3.2.2输出模块
- 使用PLC的自动化制造系统——电气接线图
- [转帖]PLC系统的组成
- 【科研论文】基于ODMA和L-PLC技术的楼宇自动化系统的设计和研究(W7100A)
- 5、PLC使用经验谈——多普康自动化制作
- 日记090820
- 深度探索C语言(一) —— 引子和基础知识技能 (原创:大鱼蓝鲸)
- 安全套接层SSL
- 5. OpenGL综合知识 --- Memory类型和数据传递
- 自己写了一个可变参数的泛型模板
- 使用PLC的自动化制造系统2.1
- 他们都欺负我..
- 如何手动整理注册表
- pku 1228 Grandpa's Estate(判断直线上顶点个数)
- vs2008打开aspx文件时设计界面死机情况的解决
- 在MFC扩展DLL项目中如何导出静态类成员变量
- 让简历避免过滤的几点意见..ZZ
- Deploy EJB2.0 On GlassFish V2.1
- C++编码中减少内存缺陷的方法和工具