Bridging signals POJ 1631
来源:互联网 发布:数据加密的保密性 编辑:程序博客网 时间:2024/06/05 19:06
Bridging signals
Time Limit: 1000MSMemory Limit: 10000KTotal Submissions: 6634Accepted: 3611
Description
'Oh no, they've done it again', cries the chief designer at the Waferland chip factory. Once more the routing designers have screwed up completely, making the signals on the chip connecting the ports of two functional blocks cross each other all over the place. At this late stage of the process, it is too expensive to redo the routing. Instead, the engineers have to bridge the signals, using the third dimension, so that no two signals cross. However, bridging is a complicated operation, and thus it is desirable to bridge as few signals as possible. The call for a computer program that finds the maximum number of signals which may be connected on the silicon surface without crossing each other, is imminent. Bearing in mind that there may be thousands of signal ports at the boundary of a functional block, the problem asks quite a lot of the programmer. Are you up to the task?
A typical situation is schematically depicted in figure 1. The ports of the two functional blocks are numbered from 1 to p, from top to bottom. The signal mapping is described by a permutation of the numbers 1 to p in the form of a list of p unique numbers in the range 1 to p, in which the i:th number specifies which port on the right side should be connected to the i:th port on the left side.Two signals cross if and only if the straight lines connecting the two ports of each pair do.
A typical situation is schematically depicted in figure 1. The ports of the two functional blocks are numbered from 1 to p, from top to bottom. The signal mapping is described by a permutation of the numbers 1 to p in the form of a list of p unique numbers in the range 1 to p, in which the i:th number specifies which port on the right side should be connected to the i:th port on the left side.Two signals cross if and only if the straight lines connecting the two ports of each pair do.
Input
On the first line of the input, there is a single positive integer n, telling the number of test scenarios to follow. Each test scenario begins with a line containing a single positive integer p < 40000, the number of ports on the two functional blocks. Then follow p lines, describing the signal mapping:On the i:th line is the port number of the block on the right side which should be connected to the i:th port of the block on the left side.
Output
For each test scenario, output one line containing the maximum number of signals which may be routed on the silicon surface without crossing each other.
Sample Input
4
6
4
2
6
3
1
5
10
2
3
4
5
6
7
8
9
10
1
8
8
7
6
5
4
3
2
1
9
5
8
9
2
3
1
7
4
6
Sample Output
3
9
1
4
Source
Northwestern Europe 2003
嗯,求最长上升子序列!大致意思是,让找条数最多的匹配,并且这些线段之间不能交叉神马意思的!
用N^2的DP会超时,所以,可以要搞优化,查找的时候用二分,所以可以用一个数组(最后一个数的下表size)存储条数为i的时候,匹配数字的最小值,这样就能够实现尽可能的多的匹配!当前dp[i]比stack[size]大的时候,直接stack[++size]=dp[i];
如果比它小的话,二分查找第一个比它大的数,改变其值!这种方法的复杂度为O(nlogn)
- POJ 1631 Bridging signals
- Bridging signals POJ 1631
- poj 1631 Bridging signals
- poj 1631 Bridging signals
- poj 1631 Bridging signals
- POJ 1631 Bridging signals
- POJ-1631-Bridging signals
- poj 1631--Bridging signals
- POJ 1631 Bridging signals
- POJ 1631 Bridging signals
- poj 1631 Bridging signals
- poj 1631 Bridging signals
- POJ - 1631 Bridging signals
- poj-1631-Bridging signals
- poj 1631 Bridging signals
- POJ 1631 Bridging signals
- poj 1631 Bridging signals
- POJ 1631 Bridging signals(LIS)
- DEBIAN 下解决GDM3不能登录root 以及中文显示
- iostream和iostream.h的区别
- IE8下设定vs2005进入调试模式
- 软件包安装、删除出错的终极解决方法
- 管道在哪里?
- Bridging signals POJ 1631
- Talking about Android process
- Use Case分析與手機畫面佈局之規劃
- 分页脚本
- “轻”量级“选手”jquery(的强大动能之)仿百度自动填充
- 神经网络中隐层数和隐层节点数问题的讨论
- 清明计划
- 高焕堂-上課講義
- Q格式/启动过程/cmd文件