RS422 serial information
来源:互联网 发布:adobe音乐编辑软件 编辑:程序博客网 时间:2024/05/18 03:56
RS422 serial information
- Introduction to RS422
- Differential balanced signals with RS422
- Electrical characteristics of RS422
- Network topology with RS422
- RS422 support forumNew
Introduction to RS422
Serial communication methods to transfer information between equipment have been defined by standards for nearly half a century. The oldest and best known standard isRS232, a standard which defines the communication betweenDTE, data terminal equipment, and DCE,data communication equipment. The relatively short distances and low speed theRS232 serial interface can handle demanded for newer standards likeRS422, RS423 and RS485. In this document, I will focus on theRS422 interface for serial balanced differential communications.Differential balanced signals with RS422
Serial, balanced and differential are the keywords for theRS422 interface standard. Serial means, that the information is sent bit by bit on a single transmission line, just like withRS232. Balanced differential is what makes RS422 different fromRS232. On RS232 interfaces, the signals are send on lines which share a common zero. WithRS422, each signal line consists of two wires, preferably twisted to reduce noise. The voltage-difference between the two lines is an indication of the signal value, rather than the voltage-level. Looking at voltage differences with RS422 rather than levels eliminates a lot of noice induced by external sources and allows for higher data rates and cable lengths compated toRS232. You can see the differences in speed and cable length betweenRS422 and other commonly used serial interface standards like RS232, RS423 and RS485 in the interface comparison table.Twisting the lines helps to reduce the noise. The noise currents induced by an external source are reversed in every twist. Instead of amplifying each other as in a straight line, the reversed noice currents reduce each others influence. The figure explains this in more detail.
Network topology with RS422
There are more differences between RS422 and RS232 than the maximum data speed and cable length. RS232 was specifically defined as an interface between computers, printers and terminals with modems. The modem would translate the communication signals to protocol usable for long distance communication, wherelong distance could also mean a device on the other side of the control room or building.RS422 allows the direct connection of intelligent devices, without the need of modems. Furthermore, where theRS232 linedriver is only designed to serve one receiver, a RS422 linedriver can serve upto ten receivers in parallel. This allows one central control unit to send commands in parallel to upto ten slave devices. Unfortunately, those slave devices cannot send information back over a shared interface line.RS422 allows a multi-drop network topology, rather than a multi-point network where all nodes are considered equal and every node has send and receive capabilities over the same line. If you need to build amulti-point communication network rather than multi-drop,RS485 is the right choice with a maximum of 32 parallel send and32 receive units parallel on one communication channel.- RS422 serial information
- Serial UART information
- RS485 serial information
- How To Get Hardware Information (CPU ID, MainBoard Info, Hard Disk Serial, System Information , ...)
- serial
- serial
- serial
- RS422电路
- information
- RS422总线、RS485和RS422对比
- RS422串口通信协议
- RS422(远距离有线通信)
- RS232 RS485 RS422
- RS232 RS485 RS422 RJ45
- RS232 RS485 RS422 串口
- RS232、RS422、RS485
- RS232 RS485 RS422介绍
- RS232 RS485 RS422 串口
- POJ 3438 Look and Say
- ubuntu中文输入法配置及简单显卡驱动安装
- Android开发之旅: Intents和Intent Filters(理论部分)
- 2011.08.07
- POJ 3659 Cell Phone Network
- RS422 serial information
- 将一个数组中的每一个元素初始化为0
- POJ 1141 Brackets Sequence
- Android中使用SAX方式解析XML文件
- RS485 serial information
- ViewFlipper 左右滑动效果
- flashbuilder 4.5.1手机版开发调用WEBSERVICE的一种方法
- 一个简单的死锁例子
- java常用类库续2(大数操作BigInteger、BigDecimal类、对象克隆技术、Arrays类)