称重传感器信号电缆长度影响
来源:互联网 发布:软件产品说明书 编辑:程序博客网 时间:2024/04/29 11:37
最好是选用6线制称重传感器。
4线的要延长的话,要用粗的,双绞线来延长。
Cable Length Effect
For high accuracy force measurement the effects of the cable on the measurement must be considered. For constant voltage excitation there are two effects of significance. These are:
1. An effect on the sensitivity due to voltage drops over the cable length.
2. An effect on the thermal span characteristics of the load cell due to the change of cable resistance with temperature.
CABLE LENGTH EFFECTS
If the load cell is sold with a cable of any length, the sensitivity is determined with the installed cable in calibration and this is not a problem. For load cells with connectors, or if the customer adds cable himself, there will be a loss of sensitivity of approximately 0.37% per 10 feet of 28 gage cable and .09% per 10 feet of 22 gage cable. This error can be eliminated if a six wire cable is run to the end of the load cell cable or connector and used in conjunction with an indicator that has sense lead capability.
TEMPERATURE EFFECTS
Since cable resistance is a function of temperature, the cable response to temperature change affects the thermal span characteristics of the load cell/cable system. For 6-wire systems this effect is eliminated. For 4-wire cables the effect is compensated for in the standard cable lengths offered with the load cells if the load cell and cable are at the same temperature at the same time. For non-standard cable lengths, there will be an effect on thermal span performance. The effect of adding 10 feet of 28 gage cable is to cause a decrease in sensitivity with temperature equal to 0.0008%/degF (an amount equal to the standard Interface specification). For an added 10 feet of 22 gage cable the effect is to decrease sensitivity by .0002%/degF (one-fourth Interface spec). In many cases a customer can tolerate the degraded performance since our standard specification is extremely tight. However, for long cable runs or high accuracy applications, this can be a significant factor. In such cases, the best approach to the problem is to run six wires to the end of the standard cable length and sense the excitation voltage at that point. This eliminates the problem.
注:
Gauge (ga)单位换算
28GA=0.015inches=0.38mm
26GA=0.018inches=0.46mm
24GA=0.024inches=0.61mm
22GA=0.030inches=0.76mm
20GA=0.036inches=1.00mm
18GA=0.048inches=1.25mm
16GA=0.060inches=1.60mm
14GA=0.075inches=2.00mm
12GA=0.105inches=2.70mm
1英尺 (foot) = 30.4厘米
- 称重传感器信号电缆长度影响
- 称重传感器原理
- 称重传感器常用技术参数
- 如何选用称重传感器
- 耐高温称重传感器
- HX711称重传感器
- 综合计装Sohgoh Keiso称重传感器
- CAS称重传感器BCL、BSA、SBA
- PT称重传感器LS、SSC、PSB、LPX
- BONGSHIN称重传感器DBBP、OSBHA、DBW
- DACELL称重传感器CMM、UMI、UMM
- Amcell称重传感器HSX、PST、QS、KM02
- 称重传感器1份检测报告
- 采用 HBM 称重传感器称量巨龟
- 称重传感器的参数及使用方法
- 电缆
- 4.2传感器信号输出
- 称重传感器并联后的误差及附加误差
- const
- 保存至工程的某一路径下
- NULL指针
- 通过v$sqlarea,v$sql查询最占用资源的查询
- PC上虚拟机中安装NW 7.02 ABAP试用版
- 称重传感器信号电缆长度影响
- GHUnit的使用
- 刷新View的方法invalidate()手动调用onDraw()
- 学到一招
- Resource is out of sync with the file system解决办法
- mysql 触发器简单示例
- 将渠道数据导出到外部文件
- Java程序练习-单链表三类字符归类
- ABAP程序中的七大危险漏洞