解读skyeye.conf

APPENDIX A: the content of  skyeye.conf



#--------------------------------------------------------------------------------

# memmap.conf and skyeye.conf are all skyeye's hareware coinfigure files.

# memmap.conf is for skyeye-v0.2.5-

# skyeye.conf is for skyeye-v0.2.5+

# usually you needn't to chang them.

# for example, a AT91's configure file is shown below:

#--------------------------------------------------------------------------------

# below is the cpu config info

# cpu maybe arm7tdmi or arm720t

cpu: arm7tdmi

#--------------------------------------------------------------------------------

# below is the machine(develop board) config info

# machine(develop board) maybe at91 or ep7312

mach: at91

#-------------------------------------------------------------------------------

#NOTICE: this parameter is useless for skyeye-V0.3.1+

# have 7 memory bank (include RAM, ROM, mapped IO space)

# below is the memory config info

mem_num: 7

# map=M means ram/rom, map=I means mapped IO space,

# type=RW means can be read or written,

# type=R means read only,

# addr=0x..... means the mem bank's beginning address,

# size=0x..... means the mem bank's memory size,  

# file=... is the filesystem image file, used for uclinux4skyeye or armlinux4skyeye

mem_bank: map=M, type=RW, addr=0x00000000, size=0x00004000

mem_bank: map=M, type=RW, addr=0x01000000, size=0x00400000

mem_bank: map=M, type=R, addr=0x01400000, size=0x00400000, file=./boot.rom

mem_bank: map=M, type=RW, addr=0x02000000, size=0x00400000

mem_bank: map=M, type=RW, addr=0x02400000, size=0x00008000

mem_bank: map=M, type=RW, addr=0x04000000, size=0x00400000

mem_bank: map=I, type=RW, addr=0xf0000000, size=0x10000000

#now, add more options on mem_bank

mem_bank: map=M, type=RW, addr=0x10000000, size=0x00000800, file=./loader.bin,boot=yes

#start binary program at 0x100000000

#----------------------------------------------------------------------------------

# below is the net config info

# state=on/off means simulated NIC is wired or not,

# mac=.... means the mac addr in simulated NIC,

# ethmod=tuntap/vnet means the virtual driver used in host evnironment,

# hostip=... means the ip address in host environment to interactive with skyeye.

# format: state=on/off mac=xx:xx:xx:xx:xx:xx ethmod=tuntap/vnet hostip=dd.dd.dd.dd

# *********NOTICE**********

#If you run two more skyeyes at the same time,

# please use different skyeye.conf for each skyeye instance, and only one

# skyeye run first and related skyeye.conf content has hostip value:

#     ......

#     net: ... ethmod=vnet, hostip=ddd.ddd.ddd.ddd

#  other skyeye.conf should has content(hostip[0] should be 0):

#     ......

#     net: ... ethmod=vnet, hostip=0.ddd.ddd.ddd

net: state=on, mac=0:4:3:2:1:f, ethmod=tuntap, hostip=10.0.0.1

#------------------------------------------------------------------------------------

#uart: use it to read/write characters in another terminal

#now you can use them to connect real serial port.

#you can add an option to skyeye.conf as below:

uart: fd_in=/dev/ttyS0, fd_out=/dev/ttyS0

#then use a terminal connect host's COM1, you can see the output in the terminal.

#-----------------------------------------------------------------------------------

#add log parameter which is used to recode the instr. flow and regs when

#program are running.

log: logon=0, logfile=/tmp/sk1.log, start=100000, end=200000

#logon = 0 or 1 0:doesn't log, 1 do log

#logfile: the filename which have the log info

#start: the start point of instruction flow to log, should >=0

#end:   the end   point of instructio flow to log



#-----------------------------------------------------------------

# below is the lcd config info

# state=on/off means simulated LCD is wired or not

lcd: state=on