mongod windows上常用操作
来源:互联网 发布:免费照片视频软件 编辑:程序博客网 时间:2024/05/24 07:30
D:\>cd MongoDB
D:\MongoDB>mongod --help
** NOTE: when using MongoDB 32 bit, you are limited to about 2 gigabytes of data
** see http://blog.mongodb.org/post/137788967/32-bit-limitations
** with --dur, the limit is lower
Allowed options:
General options:
-h [ --help ] show this usage information
--version show version information
-f [ --config ] arg configuration file specifying additional options
-v [ --verbose ] be more verbose (include multiple times for more
verbosity e.g. -vvvvv)
--quiet quieter output
--port arg specify port number
--bind_ip arg comma separated list of ip addresses to listen on - all
local ips by default
--maxConns arg max number of simultaneous connections
--logpath arg log file to send write to instead of stdout - has to be
a file, not directory
--logappend append to logpath instead of over-writing
--pidfilepath arg full path to pidfile (if not set, no pidfile is
created)
--keyFile arg private key for cluster authentication (only for
replica sets)
--auth run with security
--cpu periodically show cpu and iowait utilization
--dbpath arg directory for datafiles
--diaglog arg 0=off 1=W 2=R 3=both 7=W+some reads
--directoryperdb each database will be stored in a separate directory
--journal enable journaling
--journalOptions arg journal diagnostic options
--ipv6 enable IPv6 support (disabled by default)
--jsonp allow JSONP access via http (has security implications)
--noauth run without security
--nohttpinterface disable http interface
--noprealloc disable data file preallocation - will often hurt
performance
--noscripting disable scripting engine
--notablescan do not allow table scans
--nssize arg (=16) .ns file size (in MB) for new databases
--objcheck inspect client data for validity on receipt
--profile arg 0=off 1=slow, 2=all
--quota limits each database to a certain number of files (8
default)
--quotaFiles arg number of files allower per db, requires --quota
--rest turn on simple rest api
--repair run repair on all dbs
--repairpath arg root directory for repair files - defaults to dbpath
--slowms arg (=100) value of slow for profile and console log
--smallfiles use a smaller default file size
--syncdelay arg (=60) seconds between disk syncs (0=never, but not
recommended)
--sysinfo print some diagnostic system information
--upgrade upgrade db if needed
Windows Service Control Manager options:
--install install mongodb service
--remove remove mongodb service
--reinstall reinstall mongodb service (equivilant of mongod
--remove followed by mongod --install)
--serviceName arg windows service name
--serviceDisplayName arg windows service display name
--serviceDescription arg windows service description
--serviceUser arg user name service executes as
--servicePassword arg password used to authenticate serviceUser
Replication options:
--fastsync indicate that this instance is starting from a dbpath
snapshot of the repl peer
--autoresync automatically resync if slave data is stale
--oplogSize arg size limit (in MB) for op log
Master/slave options:
--master master mode
--slave slave mode
--source arg when slave: specify master as <server:port>
--only arg when slave: specify a single database to replicate
--slavedelay arg specify delay (in seconds) to be used when applying
master ops to slave
Replica set options:
--replSet arg arg is <setname>[/<optionalseedhostlist>]
Sharding options:
--configsvr declare this is a config db of a cluster; default port
27019; default dir /data/configdb
--shardsvr declare this is a shard db of a cluster; default port
27018
--noMoveParanoia turn off paranoid saving of data for moveChunk. this
is on by default for now, but default will switch
D:\MongoDB>
- mongod windows上常用操作
- mongod linux上常用操作
- windows上mysql常用操作
- mongod数据库的操作
- mongod 配置文件常用参数说明
- ./mongod
- mongod
- mongod连接不上的原因
- 常用windows操作命令
- windows操作常用快捷键
- windows系统常用操作
- windows常用操作
- windows常用命令行操作
- Windows 注册表常用操作
- Windows常用操作
- windows常用操作设置
- windows上常用的工具
- Mac上常用操作汇总
- 用 NSHomeDirectory()方法读取项目文件的目录
- STL map的insert操作与下标操作的区别
- 黑马第20天,IO流(列出目录下所有内容-带层次)
- ubuntu10.04下安装gcc-4.7 和g++-4.7 笔记
- .Net安装部署(Copy部署/功能部署/预编译部署)
- mongod windows上常用操作
- linux配置java环境变量(详细)
- 一些3D的基本知识
- Linux文件属性、权限设置
- JNI:使用RegisterNatives方法传递和使用Java自定义类
- Web应用界面设计规范
- IE下 struts中使用滤镜对本地图片进行预览
- C#多线程访问定义的全局变量(lock线程锁)
- hdu 2103