关于usb inrush current test 日记
来源:互联网 发布:cf出现网络出现异常 编辑:程序博客网 时间:2024/06/11 10:13
看到关于usb inrush current test的进程报告。将有关知识补习一下;
一 .硬件设备:
1. Oscilloscope
2. SQiDD board
3. N2783A current probe
二.关于inrush current
搜获一些资料,http://www.testusb.com/inrush_issue.htm
USB 2.0 Specification, Section 7.2.4.1
The purpose of the test is to ensure that the current consumed due to bulk capacitance and peripheral startup does not cause a voltage drop below valid levels that causes other devices to drop out. For this measurement a current probe, scope and Inrush Current Test Fixture is needed. The scope should have a record time of 100ms at 1 Mega sample per second. The calculation of the Inrush can be made withUSBET by saving the Inrush waveform as *.csv or *.tsv. Inrush current is measured for a minimum of 100 milliseconds after attach. Attach is defined as voltage rising to a valid level on the peripherals USB power line. Any current exceeding 100 mA during the 100ms interval is considered part of the inrush current event. The inrush current is divided into regions.
A region is an interval where the current exceeds 100 mA until the time the current falls below 100 mA for at least 100 us. There can be multiple inrush regions during the 100 ms period. Pass/Fail determination is done by the region having the highest charge value. The failures for Inrush mostly occur due to a too large capacity between Vbus and GND. The USB 2.0 Spec allows a maximum capacity of 10uF and therefore a maximum Inrush of 50uC.
Therefore, the total sum of capacity may not be higher that 10uF. Also, the device under test cannot consume more that 100mA during this 100ms of the start up. Common failures are that there is somewhere a to high capacitance on Vbus or that the device start consuming to much current in unconfigured state . Note that it is required to have at least a 1uF of capacity this in order to make ADP detection possible.
When doing the measurement make sure that you calibrate the current probe to 0mA before doing the measurement since a current probe will get quickly a DC offset that will result in a wrong measurement. It's also advisable to use the high resolution acquisition modes to reduce "the noise" on the signal.
http://compliance.usb.org/index.asp?UpdateFile=Electrical&Format=Standard#45 一些相关知识
- 关于usb inrush current test 日记
- 关于华硕主板“USB Devices Over Current Status Detected!”
- USB PHY Test
- LimeSDR-USB Quick Test
- USB test tools
- usb device over current status detected
- USB的over-current 问题总结
- tq2440 usb camera test 解析
- USB Exposed Port System Test
- test usb 禁止的解决办法
- USB开发学习日记-01
- 错误日记 quartz No Session found for current thread
- DM8168学习--USB的over-current 问题总结
- Guide to test USB camera with luvcview
- Appium 出现 > error: com.test/.activity1 never started. Current: com.test/.activity2
- 关于 TEST EAX,EAX
- 关于Test Plan
- 关于 mysql.test 数据库
- Apache与Tomcat集群配置
- Android SDK开发包国内下载地址
- 用SynchronizationContext解决界面的更新线程数据问题
- Android环境搭建(XP/Win7)
- 算法(数学)与外语是程序员未来发展的基石
- 关于usb inrush current test 日记
- #R#R的一些注意事项
- 在win7下找回丢失的桌面IE图标
- POJ 2187 Beauty Contest
- jstat用法详解
- 苹果开发帐户续费
- 展讯平台Linux下升级patch方法
- 《项目经验》--简单三层使用DataTable向数据库表批量导入数据---向SqlServer一张表中导入数据
- ubuntu12.04英文版输入中文问题