系统的编译与烧写
来源:互联网 发布:电子相册下载软件下载 编辑:程序博客网 时间:2024/06/05 20:26
编译过程:按照文档的提示将代码一条条的敲进去倒不是什么问题。可是这些命令却基本上不知道,最丢人的就是不知道.config应该是个文件,cp命令应该跟随有2个参数。编译系统时间花了1~2个小时,略长。
烧写过程:一、使用DNW软件之前需要安装实验箱连接PC的USB驱动,光盘里面的驱动无法安装,网上找到的驱动也是一样,后面猜测可能是系统不兼容 的原因。后来一询问果然如此,使用公司提供的64位版驱动就好了。哦买噶!
二、最蛋疼的CRT问题:之前的毕设就遇到CRT无法输入字符的问题,不要告诉我又是系统的原因,网上的解释无非是流控制的选项不要勾选,
在本处行不通,之前也有卸载重安装,结果也是一样。这次尝试着安装光盘中的老版本CRT,竟然好了,不知原因何在。
三、烧写完后有系统启动提示,这时候要立马按一下PC机的任意一个键使CRT进入命令模式,之后的命令也就复制下来输入就行了,一遍不行
,再来一遍,总归在试了好多遍之后烧写成功了。
OK
U-Boot 1.3.4 (Nov 10 2011 - 09:05:10) for SMDKV210
CPU: S5PV210@1000MHz(FAIL)
APLL = 1000MHz, HclkMsys = 200MHz, PclkMsys = 100MHz
MPLL = 667MHz, EPLL = 96MHz
HclkDsys = 166MHz, PclkDsys = 83MHz
HclkPsys = 133MHz, PclkPsys = 66MHz
SCLKA2M = 200MHz
Serial = CLKUART
Board: SMDKV210
DRAM: 1 GB
Flash: 8 MB
SD/MMC: 3781MB
NAND: 512 MB
*** Warning - using default environment
In: serial
Out: serial
Err: serial
checking mode for fastboot ...
Hit any key to stop autoboot: 0
SMDKV210 # nand scrub
NAND scrub: device 0 whole chip
Warning: scrub option will erase all factory set bad blocks!
There is no reliable way to recover them.
Use this command only for testing purposes if you
are sure of what you are doing!
Really scrub this NAND flash? <y/N>
Erasing at 0x28e0000 -- 8% complete.
NAND 512MiB 3,3V 8-bit: MTD Erase failure: -5
Erasing at 0xa8e0000 -- 33% complete.
NAND 512MiB 3,3V 8-bit: MTD Erase failure: -5
Erasing at 0x1d700000 -- 92% complete.
NAND 512MiB 3,3V 8-bit: MTD Erase failure: -5
Erasing at 0x1ffe0000 -- 100% complete.
Scanning device for bad blocks
s3c-nand: ECC uncorrectable error detected
s3c-nand: ECC uncorrectable error detected
s3c-nand: ECC uncorrectable error detected
s3c-nand: ECC uncorrectable error detected
s3c-nand: ECC uncorrectable error detected
s3c-nand: ECC uncorrectable error detected
dnw 30000000
OTG cable Connected!
Now, Waiting for DNW to transmit data
Download Done!! Download Address: 0x30000000, Download Filesize:0x44000
Checksum is being calculated.
Checksum O.K.
SMDKV210 # nand erase 0 80000;nand write 30000000 0 80000
NAND erase: device 0 offset 0x0, size 0x80000
Erasing at 0x60000 -- 100% complete.
OK
NAND write: device 0 offset 0x0, size 0x80000
524288 bytes written: OK
SMDKV210 # 类?
这个阶段完成后,下一步就是进入linux的驱动开发学习。
- 系统的编译与烧写
- openwrt 编译与烧写
- openwrt 编译与烧写
- openwrt 编译与烧写
- 内核编译与烧写
- busybox编译与烧写
- 20150128 【 ARM 】 交叉编译+系统烧写
- DM8168 系统编译、启动、烧写
- OK6410 烧写LINUX系统的问题与解决
- ESP8266_RTOS_SDK编译烧写与运行
- Jetson TX1uboot编译与烧写
- Arduino程序编译与烧写
- Android系统的烧写
- Android系统源代码的下载与编译
- Android系统源代码的下载与编译
- Android系统源代码的下载与编译
- Android系统源代码的下载与编译
- 安卓系统的编译与测试
- 笔记5:vb.net的FileStream操作
- Linux 安装tomcat 及过程中遇到的问题
- Ubuntu下vim方向键不管用的问题
- Java内部类总结
- win764位 vs2012+qt
- 系统的编译与烧写
- Ubuntu下使用adb
- unity3d学习笔记(十)--NGUI制作中文字体
- jsm apache-apollo-1.6 配置以及注意事项
- Sorenson H.263与H.263的区别
- 闪回查询
- notes for mordern operating system
- [置顶] C/C++左值性精髓(三)左值转换----从函数到指针的转换
- minicom以及tftp使用小结