基于S3C2440的内核3.10.17移植－－（W35i）LCD应用

来源：互联网发布：springer电子数据库编辑：程序博客网时间：2024/06/03 21:21

要想使LCD工作，需要修改arch/arm/mach-s3c24xx/mach-mini2440.c文件中的相关内容

vim arch/arm/mach-s3c24xx/mach-mini2440.c

搜索mini2440_lcd_cfg

在132行找到该结构体数组

在175行找到有如下注释：

/* mini2440 + 3.5" TFT (LCD-W35i, LQ035Q1DG06 type) + touchscreen*/

这个就是我们所需要的参数

static struct s3c2410fb_display mini2440_lcd_cfg[] __initdata = {[0] = {/* mini2440 + 3.5" TFT + touchscreen */_LCD_DECLARE(7,/* The 3.5 is quite fast */240, 21, 38, 6, /* x timing */320, 4, 4, 2,/* y timing *///320, 68, 66, 4,//240, 4, 4, 9,60),/* refresh rate */.lcdcon5= (S3C2410_LCDCON5_FRM565 |   S3C2410_LCDCON5_INVVLINE |   S3C2410_LCDCON5_INVVFRAME |   S3C2410_LCDCON5_INVVDEN |   S3C2410_LCDCON5_PWREN),},[1] = { /* mini2440 + 7" TFT + touchscreen */_LCD_DECLARE(10,/* the 7" runs slower */800, 40, 40, 48, /* x timing */480, 29, 3, 3,/* y timing */50),/* refresh rate */.lcdcon5= (S3C2410_LCDCON5_FRM565 |   S3C2410_LCDCON5_INVVLINE |   S3C2410_LCDCON5_INVVFRAME |   S3C2410_LCDCON5_PWREN),},/* The VGA shield can outout at several resolutions. All share  * the same timings, however, anything smaller than 1024x768 * will only be displayed in the top left corner of a 1024x768 * XGA output unless you add optional dip switches to the shield. * Therefore timings for other resolutions have been omitted here. */[2] = {_LCD_DECLARE(10,1024, 1, 2, 2,/* y timing */768, 200, 16, 16, /* x timing */24),/* refresh rate, maximum stable, tested with the FPGA shield */.lcdcon5= (S3C2410_LCDCON5_FRM565 |   S3C2410_LCDCON5_HWSWP),},/* mini2440 + 3.5" TFT (LCD-W35i, LQ035Q1DG06 type) + touchscreen*/[3] = {_LCD_DECLARE(/* clock */7,/* xres, margin_right, margin_left, hsync */320, 68, 66, 4,/* yres, margin_top, margin_bottom, vsync */240, 4, 4, 9,/* refresh rate */60),.lcdcon5= (S3C2410_LCDCON5_FRM565 |   S3C2410_LCDCON5_INVVDEN |   S3C2410_LCDCON5_INVVFRAME |   S3C2410_LCDCON5_INVVLINE |   S3C2410_LCDCON5_INVVCLK |   S3C2410_LCDCON5_HWSWP),},};

然后搜索关键字 features
在544行找到static char mini2440_features_str[12] __initdata = "0tb";

将其中的0tb改成3tb，即上面结构体数组中的3

保存退出

屏幕即可正常显示