关于IBM T60 X60的系统安装指南

联想在新一代的Thinkpad 6系列中采用的SATA硬盘，并在bios里面将sata的模式默认设置为AHCI，导致用户自行安装操作系统的时候出现硬件无响应，蓝屏，安装失败，但我们并不是没有办法给自己的本本重新安装操作系统，以下文字摘自IBM官方网站的文档，本人加以翻译，不对产生的任何问题负责，相关驱动我已上传，请看附件
－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－
从说明文档里我们能看到两种安装方式：
第一种是clean install，
1. Attach a diskette drive to your computer.
1，将一张软盘插入系统软驱（可以用双起U盘实现）
2. Download Intel Matrix Storage Manager Driver from the Web site and  extract the driver to C:/DRIVERS/WIN/SATA and copy the driver to  a diskette.
2，下载Intel Matrix Storage Manager Driver（我上面的帖子已提供）并把其解压到 C:/DRIVERS/WIN/SATA （其实任意地方都行），然后把它拷贝到软盘里。
3. To make sure that SATA AHCI is enabled, start the BIOS Setup  Utility menu.
4. Select "Config".
5. Select "Serial ATA (SATA)".
6. Select "AHCI".
3、4、5、6是告诉大家如何把SATA设置成AHCI模式，这个机器默认就是这样的，基本可以跳过
7. Change the startup sequence of your computer. Following the  instructions on the Startup menu in the BIOS Setup Utility, set the CD-ROM drive to start first.
7，改变启动顺序，光驱第一（这么做的目的是为了从光盘装系统，如果是从硬盘装就不用了）
8. Insert the CD for Windows XP into the CD or DVD drive, and restart the computer.
8，插入Xp安装盘并重启
9. To install a third-party SCSI or RAID driver first, press F6.
9，“安装第三方SCSI或RAID驱动，请按F6
10. When prompted, select S for Specify Additional Device.
10，当安装界面出现，选S表示Specify Additional Device
11. When prompted, insert the diskette that you created in step 2, and  press Enter.
11，然后插入你刚才拷贝了驱动程序的软盘
12. Select "Intel(R) 82801 GBM SATA AHCI Controller (Mobile ICH7M)", and  press Enter.
12，选择Intel(R) 82801 GBM SATA AHCI Controller (Mobile ICH7M，按enter
13. To continue the installation, press Enter again. Leave the diskette  in the drive until the next reboot; the software may need to be  copied from the diskette again when the files are copied during  setup.
13，再按一次enter进行继续安装，不要拿出软盘
14. Follow the instruction to complete the OS installation.
14，继续正常安装操作系统

第二种方法是针对没有软盘驱动器的用户，官方文档说明如下
If you do not have a diskette drive, you can install Intel Matrix Storage Manager Driver by the following alternative procedure:
如果你没有软驱，你可以按照下面的方法安装 Intel Matrix Storage Manager Driver
Note: If you select AHCI for Serial ATA (SATA) in the BIOS Setup  Utility before installing Intel Matrix Storage Manager Driver,   your computer will not respond; it will only display a blue screen.
注意：如果你把SATA选成了AHCI模式，那么当你安装 Intel Matrix Storage Manager Driver 之前系统会没有反应，蓝屏
1. Start the BIOS Setup Utility menu.
2. Select "Config".
3. Select "Serial ATA (SATA)".
4. Select "Compatibility".
1～4，就是开机，按F1进bios，然后把SATA选成compatibility模式。
5. Install Windows XP and Service Pack 2.
5，正常安装windows xp
6. Download Intel Matrix Storage Manager Driver from the Web site and  extract the driver to C:/DRIVERS/WIN/SATA.
6，下载 Intel Matrix Storage Manager Driver 并解压到C:/DRIVERS/WIN/SATA
7. Run Intel Matrix Storage Manager Driver. To do this, go to  C:/DRIVERS/WIN/SATA/PREPARE, and double-click install.cmd.
7，运行C:/DRIVERS/WIN/SATA/PREPARE中的install.cmd，安装Intel Matrix Storage Manager Driver
8. Turn the computer off and then on again.
8，重启
9. Start the BIOS Setup Utility menu.
10. Select "Config".
11. Select "Serial ATA (SATA)".
12. Select "AHCI".
9～12，进入bios把sata模式改回AHCI
13. Start Windows XP. The Welcome to the Found New Hardware Wizard  appears.
14. Click "No, not this time", and then click "Next".
15. Select Install from a list or specific location (Advanced), and then  click Next.
16. Select "Search for the best driver in these locations". Then select "Include this location in the search:", specify the path, C:/DRIVERS/WIN/SATA, and click "Next". The Completing the Found New  Hardware Wizard appears.
17. Click "Finish".
18. When the System Settings Change window appears, click "Yes". The computer restarts.
13～18，进入操作系统，发现新硬件，指向C:/DRIVERS/WIN/SATA完成驱动程序的安装