OSPF 正常启动时的DEBUG包
来源：互联网 发布：在交换机查ip端口号 编辑：程序博客网 时间：2024/09/21 09:02
*Mar 1 00:47:17.283: OSPF: Interface FastEthernet0/0 going Up //检测OSPF邻居端口是否为UP状态
*Mar 1 00:47:17.283: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0 from 192.168.200.1 向 224.0.0.5 area0 在f0/0端口上向200.1发送HELLO包
*Mar 1 00:47:17.351: OSPF: Rcv hello from 2.2.2.2 area 0 from FastEthernet0/0 192.168.200.2
*Mar 1 00:47:17.351: OSPF: 2 Way Communication to 2.2.2.2 on FastEthernet0/0, state 2WAY
*Mar 1 00:47:17.355: OSPF: Send immediate hello to nbr 2.2.2.2, src address 192.168.200.2, on FastEthernet0/0
*Mar 1 00:47:17.355: OSPF: Send hello to 192.168.200.2 area 0 on FastEthernet0/0 from 192.168.200.1
*Mar 1 00:47:17.355: OSPF: End of hello processing
R1(config-router)#
*Mar 1 00:47:24.855: OSPF: Rcv DBD from 2.2.2.2 on FastEthernet0/0 seq 0x5BC opt 0x52 flag 0x7 len 32 mtu 1500 state 2WAY
*Mar 1 00:47:24.859: OSPF: Nbr state is 2WAY
*Mar 1 00:47:24.859: OSPF: Rcv hello from 2.2.2.2 area 0 from FastEthernet0/0 192.168.200.2
*Mar 1 00:47:24.859: OSPF: End of hello processing
R1(config-router)#
*Mar 1 00:47:27.283: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0 from 192.168.200.1
R1(config-router)#
*Mar 1 00:47:29.859: OSPF: Rcv DBD from 2.2.2.2 on FastEthernet0/0 seq 0x5BC opt 0x52 flag 0x7 len 32 mtu 1500 state 2WAY
*Mar 1 00:47:29.859: OSPF: Nbr state is 2WAY
R1(config-router)#
*Mar 1 00:47:34.863: OSPF: Rcv hello from 2.2.2.2 area 0 from FastEthernet0/0 192.168.200.2
*Mar 1 00:47:34.863: OSPF: End of hello processing
*Mar 1 00:47:34.867: OSPF: Rcv DBD from 2.2.2.2 on FastEthernet0/0 seq 0x5BC opt 0x52 flag 0x7 len 32 mtu 1500 state 2WAY
*Mar 1 00:47:34.867: OSPF: Nbr state is 2WAY
R1(config-router)#
*Mar 1 00:47:37.283: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0 from 192.168.200.1
R1(config-router)#
*Mar 1 00:47:39.851: OSPF: Rcv DBD from 2.2.2.2 on FastEthernet0/0 seq 0x5BC opt 0x52 flag 0x7 len 32 mtu 1500 state 2WAY
*Mar 1 00:47:39.851: OSPF: Nbr state is 2WAY
R1(config-router)#
*Mar 1 00:47:44.835: OSPF: Rcv hello from 2.2.2.2 area 0 from FastEthernet0/0 192.168.200.2
*Mar 1 00:47:44.835: OSPF: End of hello processing
*Mar 1 00:47:44.863: OSPF: Rcv DBD from 2.2.2.2 on FastEthernet0/0 seq 0x5BC opt 0x52 flag 0x7 len 32 mtu 1500 state 2WAY
*Mar 1 00:47:44.863: OSPF: Nbr state is 2WAY
R1(config-router)#
*Mar 1 00:47:47.283: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0 from 192.168.200.1
R1(config-router)#
*Mar 1 00:47:49.831: OSPF: Rcv DBD from 2.2.2.2 on FastEthernet0/0 seq 0x5BC opt 0x52 flag 0x7 len 32 mtu 1500 state 2WAY
*Mar 1 00:47:49.831: OSPF: Nbr state is 2WAY
R1(config-router)#
*Mar 1 00:47:54.843: OSPF: Rcv hello from 2.2.2.2 area 0 from FastEthernet0/0 192.168.200.2
*Mar 1 00:47:54.847: OSPF: End of hello processing
*Mar 1 00:47:54.847: OSPF: Rcv DBD from 2.2.2.2 on FastEthernet0/0 seq 0x5BC opt 0x52 flag 0x7 len 32 mtu 1500 state 2WAY
*Mar 1 00:47:54.847: OSPF: Nbr state is 2WAY
R1(config-router)#
*Mar 1 00:47:57.283: OSPF: end of Wait on interface FastEthernet0/0
*Mar 1 00:47:57.283: OSPF: DR/BDR election on FastEthernet0/0
*Mar 1 00:47:57.283: OSPF: Elect BDR 1.1.1.1
*Mar 1 00:47:57.283: OSPF: Elect DR 2.2.2.2
*Mar 1 00:47:57.283: OSPF: Elect BDR 1.1.1.1
*Mar 1 00:47:57.287: OSPF: Elect DR 2.2.2.2
*Mar 1 00:47:57.287: DR: 2.2.2.2 (Id) BDR: 1.1.1.1 (Id)
*Mar 1 00:47:57.287: OSPF: Send DBD to 2.2.2.2 on FastEthernet0/0 seq 0x1D06 opt 0x52 flag 0x7 len 32
*Mar 1 00:47:57.291: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0 from 192.168.200.1
R1(config-router)#
*Mar 1 00:47:59.859: OSPF: Rcv DBD from 2.2.2.2 on FastEthernet0/0 seq 0x5BC opt 0x52 flag 0x7 len 32 mtu 1500 state EXSTART
*Mar 1 00:47:59.859: OSPF: NBR Negotiation Done. We are the SLAVE
*Mar 1 00:47:59.863: OSPF: Send DBD to 2.2.2.2 on FastEthernet0/0 seq 0x5BC opt 0x52 flag 0x2 len 52
*Mar 1 00:47:59.919: OSPF: Rcv DBD from 2.2.2.2 on FastEthernet0/0 seq 0x5BD opt 0x52 flag 0x3 len 52 mtu 1500 state EXCHANGE
*Mar 1 00:47:59.919: OSPF: Send DBD to 2.2.2.2 on FastEthernet0/0 seq 0x5BD opt 0x52 flag 0x0 len 32
*Mar 1 00:47:59.939: OSPF: Rcv DBD from 2.2.2.2 on FastEthernet0/0 seq 0x5BE opt 0x52 flag 0x1 len 32 mtu 1500 state EXCHANGE
*Mar 1 00:47:59.939: OSPF: Exchange Done with 2.2.2.2 on FastEthernet0/0
*Mar 1 00:47:59.943: OSPF: Send LS REQ to 2.2.2.2 length 12 LSA count 1
*Mar 1 00:47:59.943: OSPF: Send DBD to 2.2.2.2 on FastEthernet0/0 seq 0x5BE opt 0x52 flag 0x0 len 32
*Mar 1 00:47:59.959: OSPF: Rcv LS REQ from 2.2.2.2 on FastEthernet0/0 length 36 LSA count 1
*Mar 1 00:47:59.959: OSPF: Send UPD to 192.168.200.2 on FastEthernet0/0 length 52 LSA count 1
*Mar 1 00:47:59.971: OSPF: Rcv LS UPD from 2.2.2.2 on FastEthernet0/0 length 76 LSA count 1
*Mar 1 00:47:59.971: OSPF: Synchronized with 2.2.2.2 on FastEthernet0/0, state FULL
*Mar 1 00:47:59.971: %OSPF-5-ADJCHG: Process 100, Nbr 2.2.2.2 on FastEthernet0/0 from LOADING to FULL, Loading Done
R1(config-router)#
R1(config-router)#
*Mar 1 00:48:00.499: OSPF: Rcv LS UPD from 2.2.2.2 on FastEthernet0/0 length 76 LSA count 1
*Mar 1 00:48:00.507: OSPF: Rcv LS UPD from 2.2.2.2 on FastEthernet0/0 length 60 LSA count 1
R1(config-router)#
*Mar 1 00:48:04.871: OSPF: Rcv hello from 2.2.2.2 area 0 from FastEthernet0/0 192.168.200.2
*Mar 1 00:48:04.871: OSPF: End of hello processing
R1(config-router)#
*Mar 1 00:48:07.291: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0 from 192.168.200.1
R1(config-router)#
*Mar 1 00:48:14.863: OSPF: Rcv hello from 2.2.2.2 area 0 from FastEthernet0/0 192.168.200.2
*Mar 1 00:48:14.863: OSPF: End of hello processing
R1(config-router)#
*Mar 1 00:48:17.291: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0 from 192.168.200.1
R1(config-router)#
*Mar 1 00:48:24.847: OSPF: Rcv hello from 2.2.2.2 area 0 from FastEthernet0/0 192.168.200.2
*Mar 1 00:48:24.847: OSPF: End of hello processing
R1(config-router)#
*Mar 1 00:48:27.291: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0 from 192.168.200.1
R1(config-router)#
*Mar 1 00:48:34.855: OSPF: Rcv hello from 2.2.2.2 area 0 from FastEthernet0/0 192.168.200.2
*Mar 1 00:48:34.855: OSPF: End of hello processing
R1(config-router)#
*Mar 1 00:48:37.291: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0 from 192.168.200.1
R1(config-router)#
*Mar 1 00:48:44.843: OSPF: Rcv hello from 2.2.2.2 area 0 from FastEthernet0/0 192.168.200.2
*Mar 1 00:48:44.843: OSPF: End of hello processing
R1(config-router)#
*Mar 1 00:48:47.291: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0 from 192.168.200.1
R1(config-router)#
*Mar 1 00:48:54.831: OSPF: Rcv hello from 2.2.2.2 area 0 from FastEthernet0/0 192.168.200.2
*Mar 1 00:48:54.831: OSPF: End of hello processing
R1(config-router)#
*Mar 1 00:48:57.291: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0 from 192.168.200.1
R1(config-router)#
*Mar 1 00:49:04.867: OSPF: Rcv hello from 2.2.2.2 area 0 from FastEthernet0/0 192.168.200.2
*Mar 1 00:49:04.867: OSPF: End of hello processing
R1(config-router)#
*Mar 1 00:49:07.291: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0 from 192.168.200.1
R1(config-router)#
*Mar 1 00:49:14.827: OSPF: Rcv hello from 2.2.2.2 area 0 from FastEthernet0/0 192.168.200.2
*Mar 1 00:49:14.827: OSPF: End of hello processing
R1(config-router)#
*Mar 1 00:49:17.291: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0 from 192.168.200.1
R1(config-router)#
*Mar 1 00:49:24.847: OSPF: Rcv hello from 2.2.2.2 area 0 from FastEthernet0/0 192.168.200.2
*Mar 1 00:49:24.847: OSPF: End of hello processing
R1(config-router)#u
*Mar 1 00:49:27.291: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0 from 192.168.200.1
R1(config-router)#exit
R1(config)#exit
R1#un al
% Ambiguous command: "undebug al"
R1#
*Mar 1 00:49:32.687: %SYS-5-CONFIG_I: Configured from console by console
R1#
*Mar 1 00:49:34.831: OSPF: Rcv hello from 2.2.2.2 area 0 from FastEthernet0/0 192.168.200.2
*Mar 1 00:49:34.831: OSPF: End of hello processing
R1#deb u
*Mar 1 00:49:37.291: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0 from 192.168.200.1
*Mar 1 00:47:17.283: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0 from 192.168.200.1 向 224.0.0.5 area0 在f0/0端口上向200.1发送HELLO包
*Mar 1 00:47:17.351: OSPF: Rcv hello from 2.2.2.2 area 0 from FastEthernet0/0 192.168.200.2
*Mar 1 00:47:17.351: OSPF: 2 Way Communication to 2.2.2.2 on FastEthernet0/0, state 2WAY
*Mar 1 00:47:17.355: OSPF: Send immediate hello to nbr 2.2.2.2, src address 192.168.200.2, on FastEthernet0/0
*Mar 1 00:47:17.355: OSPF: Send hello to 192.168.200.2 area 0 on FastEthernet0/0 from 192.168.200.1
*Mar 1 00:47:17.355: OSPF: End of hello processing
R1(config-router)#
*Mar 1 00:47:24.855: OSPF: Rcv DBD from 2.2.2.2 on FastEthernet0/0 seq 0x5BC opt 0x52 flag 0x7 len 32 mtu 1500 state 2WAY
*Mar 1 00:47:24.859: OSPF: Nbr state is 2WAY
*Mar 1 00:47:24.859: OSPF: Rcv hello from 2.2.2.2 area 0 from FastEthernet0/0 192.168.200.2
*Mar 1 00:47:24.859: OSPF: End of hello processing
R1(config-router)#
*Mar 1 00:47:27.283: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0 from 192.168.200.1
R1(config-router)#
*Mar 1 00:47:29.859: OSPF: Rcv DBD from 2.2.2.2 on FastEthernet0/0 seq 0x5BC opt 0x52 flag 0x7 len 32 mtu 1500 state 2WAY
*Mar 1 00:47:29.859: OSPF: Nbr state is 2WAY
R1(config-router)#
*Mar 1 00:47:34.863: OSPF: Rcv hello from 2.2.2.2 area 0 from FastEthernet0/0 192.168.200.2
*Mar 1 00:47:34.863: OSPF: End of hello processing
*Mar 1 00:47:34.867: OSPF: Rcv DBD from 2.2.2.2 on FastEthernet0/0 seq 0x5BC opt 0x52 flag 0x7 len 32 mtu 1500 state 2WAY
*Mar 1 00:47:34.867: OSPF: Nbr state is 2WAY
R1(config-router)#
*Mar 1 00:47:37.283: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0 from 192.168.200.1
R1(config-router)#
*Mar 1 00:47:39.851: OSPF: Rcv DBD from 2.2.2.2 on FastEthernet0/0 seq 0x5BC opt 0x52 flag 0x7 len 32 mtu 1500 state 2WAY
*Mar 1 00:47:39.851: OSPF: Nbr state is 2WAY
R1(config-router)#
*Mar 1 00:47:44.835: OSPF: Rcv hello from 2.2.2.2 area 0 from FastEthernet0/0 192.168.200.2
*Mar 1 00:47:44.835: OSPF: End of hello processing
*Mar 1 00:47:44.863: OSPF: Rcv DBD from 2.2.2.2 on FastEthernet0/0 seq 0x5BC opt 0x52 flag 0x7 len 32 mtu 1500 state 2WAY
*Mar 1 00:47:44.863: OSPF: Nbr state is 2WAY
R1(config-router)#
*Mar 1 00:47:47.283: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0 from 192.168.200.1
R1(config-router)#
*Mar 1 00:47:49.831: OSPF: Rcv DBD from 2.2.2.2 on FastEthernet0/0 seq 0x5BC opt 0x52 flag 0x7 len 32 mtu 1500 state 2WAY
*Mar 1 00:47:49.831: OSPF: Nbr state is 2WAY
R1(config-router)#
*Mar 1 00:47:54.843: OSPF: Rcv hello from 2.2.2.2 area 0 from FastEthernet0/0 192.168.200.2
*Mar 1 00:47:54.847: OSPF: End of hello processing
*Mar 1 00:47:54.847: OSPF: Rcv DBD from 2.2.2.2 on FastEthernet0/0 seq 0x5BC opt 0x52 flag 0x7 len 32 mtu 1500 state 2WAY
*Mar 1 00:47:54.847: OSPF: Nbr state is 2WAY
R1(config-router)#
*Mar 1 00:47:57.283: OSPF: end of Wait on interface FastEthernet0/0
*Mar 1 00:47:57.283: OSPF: DR/BDR election on FastEthernet0/0
*Mar 1 00:47:57.283: OSPF: Elect BDR 1.1.1.1
*Mar 1 00:47:57.283: OSPF: Elect DR 2.2.2.2
*Mar 1 00:47:57.283: OSPF: Elect BDR 1.1.1.1
*Mar 1 00:47:57.287: OSPF: Elect DR 2.2.2.2
*Mar 1 00:47:57.287: DR: 2.2.2.2 (Id) BDR: 1.1.1.1 (Id)
*Mar 1 00:47:57.287: OSPF: Send DBD to 2.2.2.2 on FastEthernet0/0 seq 0x1D06 opt 0x52 flag 0x7 len 32
*Mar 1 00:47:57.291: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0 from 192.168.200.1
R1(config-router)#
*Mar 1 00:47:59.859: OSPF: Rcv DBD from 2.2.2.2 on FastEthernet0/0 seq 0x5BC opt 0x52 flag 0x7 len 32 mtu 1500 state EXSTART
*Mar 1 00:47:59.859: OSPF: NBR Negotiation Done. We are the SLAVE
*Mar 1 00:47:59.863: OSPF: Send DBD to 2.2.2.2 on FastEthernet0/0 seq 0x5BC opt 0x52 flag 0x2 len 52
*Mar 1 00:47:59.919: OSPF: Rcv DBD from 2.2.2.2 on FastEthernet0/0 seq 0x5BD opt 0x52 flag 0x3 len 52 mtu 1500 state EXCHANGE
*Mar 1 00:47:59.919: OSPF: Send DBD to 2.2.2.2 on FastEthernet0/0 seq 0x5BD opt 0x52 flag 0x0 len 32
*Mar 1 00:47:59.939: OSPF: Rcv DBD from 2.2.2.2 on FastEthernet0/0 seq 0x5BE opt 0x52 flag 0x1 len 32 mtu 1500 state EXCHANGE
*Mar 1 00:47:59.939: OSPF: Exchange Done with 2.2.2.2 on FastEthernet0/0
*Mar 1 00:47:59.943: OSPF: Send LS REQ to 2.2.2.2 length 12 LSA count 1
*Mar 1 00:47:59.943: OSPF: Send DBD to 2.2.2.2 on FastEthernet0/0 seq 0x5BE opt 0x52 flag 0x0 len 32
*Mar 1 00:47:59.959: OSPF: Rcv LS REQ from 2.2.2.2 on FastEthernet0/0 length 36 LSA count 1
*Mar 1 00:47:59.959: OSPF: Send UPD to 192.168.200.2 on FastEthernet0/0 length 52 LSA count 1
*Mar 1 00:47:59.971: OSPF: Rcv LS UPD from 2.2.2.2 on FastEthernet0/0 length 76 LSA count 1
*Mar 1 00:47:59.971: OSPF: Synchronized with 2.2.2.2 on FastEthernet0/0, state FULL
*Mar 1 00:47:59.971: %OSPF-5-ADJCHG: Process 100, Nbr 2.2.2.2 on FastEthernet0/0 from LOADING to FULL, Loading Done
R1(config-router)#
R1(config-router)#
*Mar 1 00:48:00.499: OSPF: Rcv LS UPD from 2.2.2.2 on FastEthernet0/0 length 76 LSA count 1
*Mar 1 00:48:00.507: OSPF: Rcv LS UPD from 2.2.2.2 on FastEthernet0/0 length 60 LSA count 1
R1(config-router)#
*Mar 1 00:48:04.871: OSPF: Rcv hello from 2.2.2.2 area 0 from FastEthernet0/0 192.168.200.2
*Mar 1 00:48:04.871: OSPF: End of hello processing
R1(config-router)#
*Mar 1 00:48:07.291: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0 from 192.168.200.1
R1(config-router)#
*Mar 1 00:48:14.863: OSPF: Rcv hello from 2.2.2.2 area 0 from FastEthernet0/0 192.168.200.2
*Mar 1 00:48:14.863: OSPF: End of hello processing
R1(config-router)#
*Mar 1 00:48:17.291: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0 from 192.168.200.1
R1(config-router)#
*Mar 1 00:48:24.847: OSPF: Rcv hello from 2.2.2.2 area 0 from FastEthernet0/0 192.168.200.2
*Mar 1 00:48:24.847: OSPF: End of hello processing
R1(config-router)#
*Mar 1 00:48:27.291: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0 from 192.168.200.1
R1(config-router)#
*Mar 1 00:48:34.855: OSPF: Rcv hello from 2.2.2.2 area 0 from FastEthernet0/0 192.168.200.2
*Mar 1 00:48:34.855: OSPF: End of hello processing
R1(config-router)#
*Mar 1 00:48:37.291: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0 from 192.168.200.1
R1(config-router)#
*Mar 1 00:48:44.843: OSPF: Rcv hello from 2.2.2.2 area 0 from FastEthernet0/0 192.168.200.2
*Mar 1 00:48:44.843: OSPF: End of hello processing
R1(config-router)#
*Mar 1 00:48:47.291: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0 from 192.168.200.1
R1(config-router)#
*Mar 1 00:48:54.831: OSPF: Rcv hello from 2.2.2.2 area 0 from FastEthernet0/0 192.168.200.2
*Mar 1 00:48:54.831: OSPF: End of hello processing
R1(config-router)#
*Mar 1 00:48:57.291: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0 from 192.168.200.1
R1(config-router)#
*Mar 1 00:49:04.867: OSPF: Rcv hello from 2.2.2.2 area 0 from FastEthernet0/0 192.168.200.2
*Mar 1 00:49:04.867: OSPF: End of hello processing
R1(config-router)#
*Mar 1 00:49:07.291: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0 from 192.168.200.1
R1(config-router)#
*Mar 1 00:49:14.827: OSPF: Rcv hello from 2.2.2.2 area 0 from FastEthernet0/0 192.168.200.2
*Mar 1 00:49:14.827: OSPF: End of hello processing
R1(config-router)#
*Mar 1 00:49:17.291: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0 from 192.168.200.1
R1(config-router)#
*Mar 1 00:49:24.847: OSPF: Rcv hello from 2.2.2.2 area 0 from FastEthernet0/0 192.168.200.2
*Mar 1 00:49:24.847: OSPF: End of hello processing
R1(config-router)#u
*Mar 1 00:49:27.291: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0 from 192.168.200.1
R1(config-router)#exit
R1(config)#exit
R1#un al
% Ambiguous command: "undebug al"
R1#
*Mar 1 00:49:32.687: %SYS-5-CONFIG_I: Configured from console by console
R1#
*Mar 1 00:49:34.831: OSPF: Rcv hello from 2.2.2.2 area 0 from FastEthernet0/0 192.168.200.2
*Mar 1 00:49:34.831: OSPF: End of hello processing
R1#deb u
*Mar 1 00:49:37.291: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0 from 192.168.200.1
0 0
- OSPF 正常启动时的DEBUG包
- 解决zebra下ospf正常启动却无法建立邻居的问题
- OSPF 包的传输方式
- Debug调试：debug启动不起来 正常启动却可以
- debug : 应用程序无法正常启动(0xc000007b)
- mac+eclipse 无法用debug正常启动
- ospf包
- Tomcat启动问题（debug无法启动，正常可以启动）
- eclipse设置的断点上有一个斜杠，正常启动debug不能够跳转到debug页面
- vs2015在Debug模式下运行出现"应用程序无法正常启动(0x000007b)"的错误解决方法
- Tomcat启动正常，但Debug模式下无法启动
- tomcat能正常start启动，debug模式时，加载到某个类的时候不动了，一直不动，最后超时了，设置了timeout也没用
- vs2010 ;, Debug应用程序无法正常启动(0xc0000000d).
- vs2010 ;, Debug应用程序无法正常启动(0xc0000000d).
- “Debug正常，Release崩溃”的可能原因
- 对vc6.0平台运行Debug的程序出现：应用程序无法正常启动（0xc0150002).请单击“确定”关闭应用程序
- win7系统debug调试出现“应用程序无法正常启动(0xc000007b)。请单击“确定”关闭应用程序。”的解决方法
- 在eclipse程序中设置的断点上有一个斜杠，正常启动debug不能够跳转到debug页面，怎么解决
- [linux]linux驱动模块
- java读取xml信息
- Ubuntu安装fcitx-googlepingyin
- Windows7中的VPN设置教程
- Vxworks驱动程序的结构
- OSPF 正常启动时的DEBUG包
- 百度大数据分享
- C++中的回调函数——指向类成员的指针
- Hibernate get和load区别
- 十分钟掌握diff&patch用法(转)
- linux中重要文件夹介绍
- R.java文件丢失，而且一直报xml文件错误
- 客户端(android)和服务器端(swing) Scoket通信实例
- 视频采集原理简介
