ENetwork Chapter 11 - CCNA Exploration (Version 4.0)
来源:互联网 发布:无锡大数据 编辑:程序博客网 时间:2024/05/29 17:41
Exam Viewer - ENetwork Chapter 11 - CCNA Exploration (Version 4.0)
--------------------------------------------------------------------------------
Below you will find the assessment items as presented on the exam as well as the scoring rules associated with the item.
Use of the exam information in the Exam Viewer is subject to the terms of the Academy Connection Website Usage Agreement between you and Cisco. The purpose of the Exam Viewer is to support instruction while not compromising exam security for other Cisco Networking Academies or students. This material should not be distributed outside a proctored and controlled setting. If misuse is found, action will be taken to limit access to assessment content. Please remember to logout and close your browser window after using the Exam Viewer.
1 Immediately after a router completes its boot sequence, the network administrator wants to check the routers configuration. From privileged EXEC mode, which of the following commands can the administrator use for this purpose? (Choose two.)
show flash
show NVRAM
=show startup-config
=show running-config
show version
Scoring Rule For: correctness of response
Option 3 and Option 4 are correct.
1 point for each correct option.
0 points if more options are selected than required.
Max Value = 2
This item references content from the following areas:
CCNA Exploration
11.1.6 IOS Examination Commands
2 Users in the network are experiencing slow response time when doing file transfers to a remote server. What command could be issued to determine if the router has experienced any input or output errors?
show running-config
show startup-config
=show interfaces
show ip route
show version
show memory
Scoring Rule For: correctness of response
2 points for Option 3
0 points for any other option
Max Value = 2
This item references content from the following areas:
CCNA Exploration
11.1.6 IOS Examination Commands
3
Refer to the exhibit. A technician applies the configuration in the exhibit to a clean router. To verify the configuration, the technician issues the show running-config command in the CLI session with the router. What lines should the technician expect to see in the router output from the show running-config command?
enable password class
line console 0
password ccna
enable secret cisco
enable password class
line console 0
password ccna
enable secret 5 $1$v0/3$QyQWmJyT7zCa/yaBRasJm0
enable password class
line console 0
password ccna
enable secret cisco
enable password 7 14141E0A1F17
line console 0
password 7 020507550A
enable secret 5 $1$v0/3$QyQWmJyT7zCa/yaBRasJm0
enable password 7 14141E0A1F17
line console 0
password 7 020507550A
Scoring Rule For: correctness of response
2 points for Option 5
0 points for any other option
Max Value = 2
This item references content from the following areas:
CCNA Exploration
11.2.2 Limiting Device Access - Configuring Passwords and Using Banners
4
Refer to the exhibit. A network administrator on HostA has problems accessing the FTP server. Layer three connectivity testing was successful from HostA to the S1 interface of RouterB. Which set of commands will allow the network administrator to telnet to RouterB and run debug commands?
RouterB(config)# enable secret class
RouterB(config)# line vty 0 4
RouterB(config-if)# login
RouterB(config)# enable secret class
RouterB(config)# line vty 0 2
RouterB(config-vty)# password cisco
RouterB(config-vty)# login
RouterB(config)# enable secret class
RouterB(config)# line vty 0
RouterB(config-line)# password cisco
RouterB(config-line)# login
RouterB(config)# enable secret class
RouterB(config)# line aux 0
RouterB(config-line)# password cisco
RouterB(config-line)# login
RouterB(config)# enable secret class
RouterB(config)# line aux 0
RouterB(config-vty)# password cisco
RouterB(config-vty)# login
Scoring Rule For: correctness of response
2 points for Option 3
0 points for any other option
Max Value = 2
This item references content from the following areas:
CCNA Exploration
11.2.2 Limiting Device Access - Configuring Passwords and Using Banners
5
The connection between routers B and C has been successfully tested. However, after rebooting router C, the administrator noticed the response time between networks 10.10.3.0 and 10.10.4.0 is slower. Ping between the two routers is successful. A trace route indicates three hops from router B to router C. What else can be done to troubleshoot the problem?
Ping router B S0/1 connection from router C.
Trace the connection between router B to router C S0/1.
Issue a show ip route command in router B to verify routing is enabled.
=Issue a show ip interface brief command on router C.
Scoring Rule For: correctness of response
2 points for Option 4
0 points for any other option
Max Value = 2
This item references content from the following areas:
CCNA Exploration
11.3.2 Testing the Interface Assignment
6 What command is used to change the default router name to Fontana?
Router# name Fontana
Router# hostname Fontana
Router(config)# name Fontana
=Router(config)# hostname Fontana
Scoring Rule For: correctness of response
2 points for Option 4
0 points for any other option
Max Value = 2
This item references content from the following areas:
CCNA Exploration
11.2.1 Devices Need Names
7
The serial connection shown in the graphic needs to be configured. Which configuration commands must be made on the Sydney router to establish connectivity with the Melbourne site? (Choose three.)
=Sydney(config-if)# ip address 201.100.53.2 255.255.255.0
=Sydney(config-if)# no shutdown
Sydney(config-if)# ip address 201.100.53.1 255.255.255.224
=Sydney(config-if)# clock rate 56000
Sydney(config-if)# ip host Melbourne 201.100.53.2
Scoring Rule For: correctness of response
Option 1, Option 2, and Option 4 are correct.
1 point for each correct option.
0 points if more options are selected than required.
Max Value = 3
This item references content from the following areas:
CCNA Exploration
11.2.4 Configuring Interfaces
8
Refer to the exhibit. The output is shown for the show ip route command executed on Router A. What does the IP address 192.168.2.2 represent?
Gateway for the 192.168.1.0 network
Gateway for the 192.168.3.0 network
IP assigned to the serial port on Router A
=IP assigned to the serial port on Router B
Scoring Rule For: correctness of response
2 points for Option 4
0 points for any other option
Max Value = 2
This item references content from the following areas:
CCNA Exploration
11.1.1 Cisco IOS
9
Refer to the exhibit. What additional command is required to allow remote access to this switch from hosts outside the local network?
NA-SW1(config-if)# no shutdown
NA-SW1(config)# enable password password
=NA-SW1(config)# ip default-gateway address
NA-SW1(config-if)# description description
Scoring Rule For: correctness of response
2 points for Option 3
0 points for any other option
Max Value = 2
This item references content from the following areas:
CCNA Exploration
11.5.4 Network Testing
10 In a Cisco device, where is the IOS file stored prior to system startup?
RAM
ROM
=Flash
NVRAM
Scoring Rule For: correctness of response
2 points for Option 3
0 points for any other option
Max Value = 2
This item references content from the following areas:
CCNA Exploration
11.1.1 Cisco IOS
11 When network services fail, which port is most often used to access a router for management purposes?
AUX
Ethernet
=Console
Telnet
SSH
Scoring Rule For: correctness of response
2 points for Option 3
0 points for any other option
Max Value = 2
This item references content from the following areas:
CCNA Exploration
11.1.1 Cisco IOS
12 A network administrator needs to keep the user ID, password, and session contents private when establishing remote CLI connectivity with a router to manage it. Which access method should be chosen?
Telnet
Console
AUX
=SSH
Scoring Rule For: correctness of response
2 points for Option 4
0 points for any other option
Max Value = 2
This item references content from the following areas:
CCNA Exploration
11.1.1 Cisco IOS
13 In a Cisco router, when do changes made to the running-configuration take effect?
after a system restart
=as the commands are entered
when logging off the system
when the configuration is saved to the startup-configuration
Scoring Rule For: correctness of response
2 points for Option 2
0 points for any other option
Max Value = 2
This item references content from the following areas:
CCNA Exploration
11.1.2 Configuration Files
14
Refer to the exhibit. Which names correctly identify the CLI mode represented by the prompt for Switch-East4#? (Choose two.)
line configuration mode
user executive mode
global configuration mode
=privileged executive mode
interface configuration mode
=enable mode
Scoring Rule For: correctness of response
Option 4 and Option 6 are correct.
1 point for each correct option.
0 points if more options are selected than required.
Max Value = 2
This item references content from the following areas:
CCNA Exploration
11.1.3 Cisco IOS Modes
15 Which three terms correctly define the forms of help available within the Cisco IOS? (Choose three.)
=hot keys
context-check
=context-sensitive
structured check
command override
=command syntax check
Scoring Rule For: correctness of response
Option 1, Option 3, and Option 6 are correct.
1 point for each correct option.
0 points if more options are selected than required.
Max Value = 3
This item references content from the following areas:
CCNA Exploration
11.1.5 Using CLI Help
16 Which combination of keys would be used at the CLI prompt to interrupt a ping or traceroute process?
Ctrl-C
Ctrl-P
Ctrl-R
=Ctrl-Shift-6
Ctrl-Z
Scoring Rule For: correctness of response
2 points for Option 4
0 points for any other option
Max Value = 2
This item references content from the following areas:
CCNA Exploration
11.1.5 Using CLI Help
17
Refer to the exhibit. What command will place the router into the correct mode to configure an appropriate interface to connect to a LAN?
UBAMA# configure terminal
UBAMA(config)# line vty 0 4
UBAMA(config)# line console 0
UBAMA(config)# interface Serial 0/0/0
=UBAMA(config)# interface FastEthernet 0/1
Scoring Rule For: correctness of response
2 points for Option 5
0 points for any other option
Max Value = 2
This item references content from the following areas:
CCNA Exploration
11.2.1 Devices Need Names
18 On a Cisco router, which interface would be used to make the initial configuration?
Scoring Rule For: correctness of response
2 points for Option 2
0 points for any other option
Max Value = 2
This item references content from the following areas:
CCNA Exploration
11.1.1 Cisco IOS
19
Refer to the exhibit. A student is responsible for the IP addressing, configuration and connectivity testing of the network shown in the graphic. A ping from host B to host C results in a destination unreachable but a ping from host B to host A was successful. What two reasons could account for this failure based on the graphic and partial router output for the Dallas router? (Choose two.)
The host A is turned off.
The Fa0/0 interface on Dallas is shutdown.
The LAN cable is disconnected from host B.
=The S0/0/1 IP address of Dallas is improperly configured.
The Fa0/0 interface on Dallas is in a different subnet than host B.
=The clock rate is missing on the serial link between Dallas and NYC.
Scoring Rule For: correctness of response
Option 4 and Option 6 are correct.
1 point for each correct option.
0 points if more options are selected than required.
Max Value = 2
This item references content from the following areas:
CCNA Exploration
11.2.4 Configuring Interfaces
Showing 1 of 1 Prev Page: 1 Next
Close Window
All contents copyright ?2001-2008 Cisco Systems, Inc. All rights reserved. Privacy Statement and Trademarks.
- ENetwork Chapter 11 - CCNA Exploration (Version 4.0)
- ENetwork Chapter 2 - CCNA Exploration (Version 4.0)
- ENetwork Chapter 3 - CCNA Exploration (Version 4.0)
- ENetwork Chapter 4 - CCNA Exploration (Version 4.0)
- ENetwork Chapter 5 - CCNA Exploration (Version 4.0)
- ENetwork Chapter 7 - CCNA Exploration (Version 4.0)
- ENetwork Chapter 8 - CCNA Exploration (Version 4.0)
- ENetwork Chapter 6 - CCNA Exploration (Version 4.0)
- ENetwork Chapter 9 - CCNA Exploration (Version 4.0)
- DsmbISP Chapter 1 - CCNA Discovery: 在中小型企业或 ISP 工作 (Version 4.
- ccna 1 Chapter 2
- ccna 1 Chapter 3
- ccna 1 Chapter 4
- ccna 1 Chapter 5
- CCNA 3 Chapter 1
- CCNA 3 Chapter 2
- CCNA 3 Chapter 3
- CCNA 3 Chapter 4
- Android 高仿 频道管理----网易、今日头条、腾讯视频 (可以拖动的GridView)附源码DEMO
- hbase 0.98.1集群安装
- 【原创】新辰:写给做淘宝电商的一些推广秘密 让你的产品爆起来
- java--TreeMap按key和value分别排序
- 在Hadoop研究过程中遇到问题杂记(后续再补充)
- ENetwork Chapter 11 - CCNA Exploration (Version 4.0)
- oracle笔记1-有效、干净的卸载oracle
- PHP 设计模式(二)
- 利用PLSQ中LODBC Import选项导入Excel数据到数据库表中
- AttributeError: 'Response' object has no attribute 'json'
- HDU 2521 反素数
- Sybase 中文乱码解决办法
- 解决安卓手机搜不到ubuntu13.10下WIFI热点的问题
- 使用Vitamio打造自己的Android万能播放器(3)——本地播放(主界面、播放列表)