BCM wifi分析

一：加载wifi驱动模块

    在hardware/libhardware_legacy/wifi/wifi.c调用函数

    insmod(DRIVER_MODULE_PATH, DRIVER_MODULE_ARG)

    其中

     DRIVER_MODULE_PATH = /system/lib/dhd.ko

      DRIVER_MODULE_ARG  = "firmware_path=/etc/wifi/40181/fw_bcm40181a2.bin nvram_path=/etc/wifi/40181/nvram.txt"

二：wifi驱动模块运行

     wifi驱动入口dhd_module_init(void) ... dhd_linux.c

dhd_module_init(void){int error = 0;DHD_TRACE(("%s: Enter\n", __FUNCTION__));wl_android_init(); //初始化dhd_msg_level |= DHD_ERROR_VAL,给iface_name赋值为wlando {sema_init(&dhd_chipup_sem, 0);dhd_bus_reg_sdio_notify(&dhd_chipup_sem);//注册sdio driver,支持如下图wifi列表，sdio驱动获取wifi列表的设备后调用dummy_probe() --> up(dhd_chipup_sem)                dhd_customer_gpio_wlan_ctrl(WLAN_POWER_ON);                if (down_timeout(&dhd_chipup_sem, //2000ms超时等待msecs_to_jiffies(POWERUP_WAIT_MS)) == 0) {dhd_bus_unreg_sdio_notify();chip_up = 1;break;}DHD_ERROR(("\nfailed to power up wifi chip, retry again (%d left) **\n\n",retry+1));dhd_bus_unreg_sdio_notify();dhd_customer_gpio_wlan_ctrl(WLAN_POWER_OFF);} while (retry-- > 0);if (!chip_up) {DHD_ERROR(("\nfailed to power up wifi chip, max retry reached, exits **\n\n"));return -ENODEV;}sema_init(&dhd_registration_sem, 0);error = dhd_bus_register();//详细分析看<三>,注册dhd_sdio驱动，最终会调用到dhd_net_attach();if (!error)printf("\n%s\n", dhd_version);else {DHD_ERROR(("%s: sdio_register_driver failed\n", __FUNCTION__));goto fail_1;}/* * Wait till MMC sdio_register_driver callback called and made driver attach. * It's needed to make sync up exit from dhd insmod  and * Kernel MMC sdio device callback registration */if ((down_timeout(&dhd_registration_sem,//函数dhd_net_attach() --> up(&dhd_registration_sem);msecs_to_jiffies(DHD_REGISTRATION_TIMEOUT)) != 0) ||(dhd_registration_check != TRUE)) {error = -ENODEV;DHD_ERROR(("%s: sdio_register_driver timeout or error \n", __FUNCTION__));goto fail_2;}wl_android_post_init();return error;fail_2:dhd_bus_unregister();fail_1:/* Call customer gpio to turn off power with WL_REG_ON signal */dhd_customer_gpio_wlan_ctrl(WLAN_POWER_OFF);return error;}

三：dhd_bus_register(void) ... dhd_sdio.c分析

bcmsdh_register(&dhd_sdio)会调用pci_register_driver(&bcmsdh_pci_driver)注册一个pci类型的驱动，如果匹配到bcmsdh_pci_devid就会调用到bcmsdh_pci_probe --> drvinfo.attach --> drvinfo.attach ,最终调用到dhd_sdio->dhdsdio_probe，接下来分析dhdsdio_probe函数

四：dhdsdio_probe() ... dhd_sdio.c分析

dhdsdio_probe(uint16 venid, uint16 devid, uint16 bus_no, uint16 slot,uint16 func, uint bustype, void *regsva, osl_t * osh, void *sdh){int ret;dhd_bus_t *bus;/* attach the common module */dhd_common_init(osh);/* attempt to attach to the dongle */if (!(dhdsdio_probe_attach(bus, osh, sdh, regsva, devid))) {DHD_ERROR(("%s: dhdsdio_probe_attach failed\n", __FUNCTION__));goto fail;}/* Attach to the dhd/OS/network interface */ //创建3个线程，分别是dhd_watchdog_thread、dhd_dpc、dhd_sysiocif (!(bus->dhd = dhd_attach(osh, bus, SDPCM_RESERVE))) {DHD_ERROR(("%s: dhd_attach failed\n", __FUNCTION__));goto fail;}/* Allocate buffers */if (!(dhdsdio_probe_malloc(bus, osh, sdh))) {DHD_ERROR(("%s: dhdsdio_probe_malloc failed\n", __FUNCTION__));goto fail;}if (!(dhdsdio_probe_init(bus, osh, sdh))) {DHD_ERROR(("%s: dhdsdio_probe_init failed\n", __FUNCTION__));goto fail;}if (bus->intr) {/* Register interrupt callback, but mask it (not operational yet). */DHD_INTR(("%s: disable SDIO interrupts (not interested yet)\n", __FUNCTION__));bcmsdh_intr_disable(sdh);if ((ret = bcmsdh_intr_reg(sdh, dhdsdio_isr, bus)) != 0) {DHD_ERROR(("%s: FAILED: bcmsdh_intr_reg returned %d\n",           __FUNCTION__, ret));goto fail;}DHD_INTR(("%s: registered SDIO interrupt function ok\n", __FUNCTION__));} else {DHD_INFO(("%s: SDIO interrupt function is NOT registered due to polling mode\n",           __FUNCTION__));}DHD_INFO(("%s: completed!!\n", __FUNCTION__));        //获取wifi MAC地址ret = dhd_custom_get_mac_address(ea_addr.octet);/* if firmware path present try to download and bring up bus */if (dhd_download_fw_on_driverload) {  //更新模组firmware、nvram，其中使用了filp_open、kernel_read、filp_close进行文件系统的操作if ((ret = dhd_bus_start(bus->dhd)) != 0) {DHD_ERROR(("%s: dhd_bus_start failed\n", __FUNCTION__));goto fail;}}/* Ok, have the per-port tell the stack we're open for business */if (dhd_net_attach(bus->dhd, 0) != 0) {DHD_ERROR(("%s: Net attach failed!!\n", __FUNCTION__));goto fail;}return bus;fail:dhdsdio_release(bus, osh);return NULL;}