嵌入式 linux下网络质量测试工具ipref工具小结
来源:互联网 发布:网络民族志与田野调查 编辑:程序博客网 时间:2024/05/01 04:02
1、首先看一下iperf的参数:
root@u12d32:/qy_work/a3518_v080_develop/a3518c_ko_hi/ko# iperf -h
Usage: iperf [-s|-c host] [options]
iperf [-h|--help] [-v|--version]
Iperf是一个网络性能测试工具。可以测试TCP和UDP带宽质量,可以测量最大TCP带宽,具有多种参数和UDP特性,可以报告带宽,延迟抖动和数据包丢失。Iperf在linux和windows平台均有二进制版本供自由使用。
Iperf was developed by NLANRDAST as a modern alternative for measuring maximum TCP and UDP bandwidth performance. Iperf allows the tuning of various parameters and UDP characteristics. Iperf reports bandwidth, delay jitter, datagram loss.
Iperf使用方法与参数说明
参数说明
-s 以server模式启动,eg:iperf -s
-c host以client模式启动,host是server端地址,eg:iperf -c 222.35.11.23
通用参数
-f [kmKM] 分别表示以Kbits, Mbits, KBytes, MBytes显示报告,默认以Mbits为单位,eg:iperf -c 222.35.11.23 -f K
-i sec 以秒为单位显示报告间隔,eg:iperf -c 222.35.11.23 -i 2
-l 缓冲区大小,默认是8KB,eg:iperf -c 222.35.11.23 -l 16
-m 显示tcp最大mtu值
-o 将报告和错误信息输出到文件eg:iperf -c 222.35.11.23 -o ciperflog.txt
-p 指定服务器端使用的端口或客户端所连接的端口eg:iperf -s -p 9999;iperf -c 222.35.11.23 -p 9999
-u 使用udp协议
-w 指定TCP窗口大小,默认是8KB
-B 绑定一个主机地址或接口(当主机有多个地址或接口时使用该参数)
-C 兼容旧版本(当server端和client端版本不一样时使用)
-M 设定TCP数据包的最大mtu值
-N 设定TCP不延时
-V 传输ipv6数据包
server专用参数
-D 以服务方式运行iperf,eg:iperf -s -D
-R 停止iperf服务,针对-D,eg:iperf -s -R
client端专用参数
-d 同时进行双向传输测试
-n 指定传输的字节数,eg:iperf -c 222.35.11.23 -n 100000
-r 单独进行双向传输测试
-t 测试时间,默认10秒,eg:iperf -c 222.35.11.23 -t 5
-F 指定需要传输的文件
-T 指定ttl值
应用实例
使用 iperf -s 命令将 Iperf 启动为 server 模式,在客户机上使用 iperf -c启动client模式。
iperf –s
------------------------------------------------------------
Server listening on TCP port 5001
TCP window size: 8.00 KByte (default)
------------------------------------------------------------
iperf -c 59.128.103.56
上面使用服务端和客户端的默认设置进行测试
iperf -s -w 300K
------------------------------------------------------------
Server listening on TCP port 5001
TCP window size: 300 KByte
------------------------------------------------------------
iperf -c 59.128.103.56 -f K -i 2 -w 300K
设定报告间隔为2秒,服务器端和客户端的TCP窗口都开到300KB
iperf -c 59.128.103.56 -f K -i 2 -w 300K –n 1000000
测试传输约1MB数据
iperf -c 59.128.103.56 -f K -i 2 -w 300K –t 36
测试持续36秒
iperf -c 59.128.103.56 -f K -i 2 -w 300K -n 10400000 –d
测试双向的传输
iperf -c 59.128.103.56 -f K -i 2 -w 300K –u
UDP测试
其中 -i 参数的含义是周期性报告的时间间隔(interval),单位为秒;在上面的例子中,表示每隔2秒报告一次带宽等信息。
启动一个iperf服务器进程
首先要介绍的命令用来启动iperf服务器监听进程以便监听客户端连接的。命令如下:
iperf -s -P 2 -i 5 -p 5999 -f k
这个命令会启动iperf,后续参数用来设定监听5999 端口(默认端口是5001), 限定iperf只允许两个连接,每5秒汇报一次连接情况。连接限制参数(-P参数)非常重要,当两个连接建立后,服务器进程就会退出。如果这个参数设定为0,那么iperf 进程将持续监听端口,并且不限制连接数量。在 Windows主机上键入该命令,会显示出如下所示界面:
root@u12d32:/qy_work/a3518_v080_develop/a3518c_ko_hi/ko# iperf -s -P 2 -i 5 -p 5999 -f k------------------------------------------------------------
Server listening on TCP port 5999
TCP window size: 85.3 KByte (default)
------------------------------------------------------------
启动一个iperf 客户端连接
iperf 的另一半就是客户端,用来连接到服务器监听端口。比如我们要连接到一台叫做 s-network1.amcs.tld 的服务器,端口为5999,连接60 秒并且每5秒显示一次状态,命令行如下:
iperf -c 10.10.2.59 -P 1 -i 5 -p 5999 -f B -t 60 -T 1
命令启动后,s-network1 主机被用来进行网络性能检测。与Jperf GUI 界面提供的漂亮图形不同, iperf只会根据测量参数简单的报告网络带宽状况,在本例中是以 比特为单位(-f 参数)进行带宽表示的。图B显示了远程客户端与s-network1主机间的带宽性能。
root@u12d32:~# iperf -c 10.10.2.59 -P 1 -i 5 -p 5999 -f B -t 60 -T 1
------------------------------------------------------------
Client connecting to 10.10.2.59, TCP port 5999
TCP window size: 170840 Byte (default)
------------------------------------------------------------
[ 3] local 10.10.2.59 port 41823 connected with 10.10.2.59 port 5999
[ ID] Interval Transfer Bandwidth
[ 3] 0.0- 5.0 sec 17222598656 Bytes 3444519731 Bytes/sec
为了应对日常便捷应用的需求,我们可以建立一个 .bat批处理文件,届时填入服务器名称即可实现快速检测。以下为实际使用的拷屏:
C:\jperf\jperf\bin>iperf
Usage: iperf [-s|-c host] [options]
Try `iperf --help' for more information.
C:\jperf\jperf\bin>iperf --help
Usage: iperf [-s|-c host] [options]
iperf [-h|--help] [-v|--version]
Client/Server:
-f, --format [kmKM] format to report: Kbits, Mbits, KBytes, MBytes
-i, --interval # seconds between periodic bandwidth reports
-l, --len #[KM] length of buffer to read or write (default 8 KB)
-m, --print_mss print TCP maximum segment size (MTU - TCP/IP header)
-o, --output <filename> output the report or error message to this specified file
-p, --port # server port to listen on/connect to
-u, --udp use UDP rather than TCP
-w, --window #[KM] TCP window size (socket buffer size)
-B, --bind <host> bind to <host>, an interface or multicast address
-C, --compatibility for use with older versions does not sent extra msgs
-M, --mss # set TCP maximum segment size (MTU - 40 bytes)
-N, --nodelay set TCP no delay, disabling Nagle's Algorithm
-V, --IPv6Version Set the domain to IPv6
Server specific:
-s, --server run in server mode
-D, --daemon run the server as a daemon
-R, --remove remove service in win32
Client specific:
-b, --bandwidth #[KM] for UDP, bandwidth to send at in bits/sec
(default 1 Mbit/sec, implies -u)
-c, --client <host> run in client mode, connecting to <host>
-d, --dualtest Do a bidirectional test simultaneously
-n, --num #[KM] number of bytes to transmit (instead of -t)
-r, --tradeoff Do a bidirectional test individually
-t, --time # time in seconds to transmit for (default 10 secs)
-F, --fileinput <name> input the data to be transmitted from a file
-I, --stdin input the data to be transmitted from stdin
-L, --listenport # port to recieve bidirectional tests back on
-P, --parallel # number of parallel client threads to run
-T, --ttl # time-to-live, for multicast (default 1)
Miscellaneous:
-h, --help print this message and quit
-v, --version print version information and quit
[KM] Indicates options that support a K or M suffix for kilo- or mega-
The TCP window size option can be set by the environment variable
TCP_WINDOW_SIZE. Most other options can be set by an environment variable
IPERF_<long option name>, such as IPERF_BANDWIDTH.
- 嵌入式 linux下网络质量测试工具ipref工具小结
- 嵌入式linux网络性能测试工具iperf
- linux下网络探测工具nmap的使用小结
- linux下网络连接socket统计工具ss学习小结
- linux下网络数据包抓取工具tcpdump学习小结
- Linux 下sar工具小结
- Red Hat Linux下测试网络时延工具mtr
- 简谈linux环境下网络性能测试工具iperf
- Linux下网络性能测试Netperf工具介绍及安装
- Linux下网络性能测试Netperf工具介绍及安装
- Linux下网络性能测试Netperf工具介绍及安装
- Python网络质量测试工具增加乱序统计
- linux网络测速工具Speedometer(嵌入式工具集合)
- Linux--系统网络测试和测试工具
- linux下稳定性测试工具
- linux下网络调试工具
- linux下网络发包工具
- 一些嵌入式测试工具
- Spring3.0官网文档学习笔记(二)
- WCF初探-2:手动实现WCF程序
- 如何去除脸上的斑
- EditText与Textiew inputType属性详解
- DIV+js+css跟随鼠标的浮动提示框
- 嵌入式 linux下网络质量测试工具ipref工具小结
- 分享比较全的教程
- 让jquery变高效的小秘密
- 经纬财富:北海现货白银(天通银)与纸白银之间的区别与联系
- Yahoo!团队:网站性能优化的35条黄金守则
- 配置个性化PowerShell Console Profile
- Linux 运行程序时找不到so文件
- Filter系列二
- 【中英】mac电脑清理软件 ToolWiz Mac Boost