帧中继实验
来源:互联网 发布:上海市行知实验中学 编辑:程序博客网 时间:2024/05/22 14:25
一、在Packet Tracer上边画好拓扑,并配置好模块和帧中继DLCI
先看下配好的拓扑图:
配置过程:
1、添加3台路由器,我用的是2811,为路由器添加S端口模块,我用的是NM-4A/S模块。
2、添加一个Cloud-PT-Empty设备(Cloud0)模拟帧中继网络,为Cloud0添加3个S端口模 块,好与路由器连接!
?
3、设置好S1,S2,S3,的DLCI值:
?
?
4、配置好Frame-relay连接:
?
5、连接端口注意:路由器作为DTE设备,Cloud0作为DCE设备,按照拓扑添加3台PC作测试用,连接到路由 器F端口,并启动各连接端口。为各PC设置好IP和网关:
?
做好ip地址的规划,网络拓扑就基本完成了,下面进行路由器的配置
二、配置3台路由器:
R1路由器配置:
R1>en
R1#conf t
R1(config)#int s1/0?????????????????????????????????? 进入S1/0端口配置
R1(config-if)#no shut???????????????????????????????? 启动端口
R1(config-if)#encapsulation frame-relay?????????????? 帧中继封装
R1(config-if)#frame-relay lmi-type cisco????????????? 帧中继类型为cisco
R1(config)#int s1/0.1 point-to-point????????????????? 配置子端口,并设置为点对点模式
R1(config-subif)#ip add 192.168.1.1 255.255.255.0???? 分配子端口ip地址
R1(config-subif)#frame-relay interface-dlci 102?????? 指定点对点对应的DLCI值
R1(config-subif)#exit
R1(config)#int s1/0.2 point-to-point????????????????? 配置子端口,并设置为点对点模式
R1(config-subif)#ip add 192.168.2.1 255.255.255.0???? 分配子端口ip地址
R1(config-subif)#frame-relay interface-dlci 103?????? 指定点对点对应的DLCI值
R1(config-subif)#exit
R2路由器配置:
R2>en
R2#conf t
R2(config)#int s1/0
R2(config-if)#no shut
R2(config-if)#en frame-relay
R2(config-if)#frame-relay lmi-type cisco
R2(config)#int s1/0.1 point-to-point
R2(config-subif)#ip add 192.168.1.2 255.255.255.0
R2(config-subif)#frame-relay interface-dlci 201
R2(config-subif)#exit
R2(config)#int s1/0.2 p
R2(config-subif)#ip add 192.168.3.1 255.255.255.0
R2(config-subif)#frame-relay interface-dlci 203
R2(config-subif)#exit
R3路由器配置:
R3>en
R3#conf t
R3(config)#int s1/0
R3(config-if)#no shut
R3(config-if)#en frame-relay
R3(config-if)#frame-relay lmi-type cisco
R3(config)#int s1/0.1 point-to-point
R3(config-subif)#ip add 192.168.3.2 255.255.255.0
R3(config-subif)#frame-relay interface-dlci 302
R3(config-subif)#exit
R3(config)#int s1/0.2 point-to-point
R3(config-subif)#ip add 192.168.2.2 255.255.255.0
R3(config-subif)#frame-relay interface-dlci 301
R3(config-subif)#exit
在三台路由器上启动rip路由:
R1(config)#router rip???????????????????????????????? 启动rip路由
R1(config-router)#net 192.168.10.0??????????????????? 申明接口网络地址
R1(config-router)#net 192.168.1.0???????????????????? 申明接口网络地址
R1(config-router)#net 192.168.2.0???????????????????? 申明接口网络地址
R1(config-router)#exit
R1(config)#
R2(config)#router rip
R2(config-router)#net 192.168.20.0
R2(config-router)#net 192.168.1.0
R2(config-router)#net 192.168.3.0
R2(config-router)#exit
R2(config)#
R3(config)#router rip
R3(config-router)#net 192.168.30.0
R3(config-router)#net 192.168.3.0
R3(config-router)#net 192.168.2.0
R3(config-router)#exit
R3(config)#exit
Router#
完成配置后,用PC1~3检验是否成功,实验完成!
- 帧中继实验
- 帧中继实验
- 实验十一:帧中继
- Frame-relay 帧中继实验
- CCNA实验—帧中继
- 实验24:帧中继点对点实验
- CCNA实验三十一 帧中继的Tunnel
- Dynamips-帧中继点到多点子接口实验
- CCNA实验二十八 帧中继(Frame Relay)
- CCNA实验二十九 帧中继点到点子接口
- CCNA实验三十 帧中继点到多点子接口
- 帧中继多点子接口上运行EIGRP_实验
- 帧中继
- 帧中继
- 帧中继
- 帧中继
- 帧中继
- 帧中继
- HDU最短路劲基础题 难度解析
- poj 3667 线段树
- Ubuntu下设置通过NAT方式上网(静态IP)
- gem install mysql2 失败的解决方法
- Android Studio导入Project的方法
- 帧中继实验
- 微信内部浏览器私有接口 - WeixinJSBridge介绍
- 以XML的方式保存密码
- Resin#unexpected end of file in utf8 character解决过程
- Subsets
- 简单的HTML中常用的一些特效方法
- UVA10720- Graph Construction
- 动态规划—北大POJ Charm Bracelet(01背包问题)
- 对于Mahout__"推荐算法"的初步认识(2)