ucgui界面设计示例2

ucgui界面设计示例2

本文博客链接:http://blog.csdn.net/jdh99,作者:jdh,转载请注明.

环境：

主机:WIN8

开发环境:MDK4.72

ucgui版本：3.90

mcu: stm32f103VE

说明:

本程序基于ucgui对话框机制设计了一个界面，并用6个实体按键对界面进行控制，并增加了进度条显示

效果图：

 

源码：

gui_match.h

/**********************************************************************对码绑定界面模块头文件*(c)copyright 2014,jdh*  All Right Reserved*新建时间:2014/10/24 by jdh**********************************************************************/#ifndef _GUI_MATCH_H_#define _GUI_MATCH_H_/**********************************************************************头文件**********************************************************************/#include "world.h"/**********************************************************************宏定义**********************************************************************//**********************************************************************工作间隔*单位:ms**********************************************************************/#define INTERVAL_GUI_MATCH100  /**********************************************************************进度条显示时间*单位:ms**********************************************************************/#define TIME_PROGBAR_GUI_MATCH3000 /**********************************************************************函数**********************************************************************//**********************************************************************模块载入**********************************************************************/void gui_match_load(void);/**********************************************************************模块运行**********************************************************************/void gui_match_run(void);/**********************************************************************设置显示状态*参数:enable:0:关闭显示,1:打开显示**********************************************************************/void gui_match_show(uint8_t enable);/**********************************************************************得到当前的显示状态*返回:0:关闭显示,1:打开显示**********************************************************************/uint8_t gui_match_get_show(void);/**********************************************************************得到绑定的脚镣id*返回:0:未绑定,其他:脚镣id**********************************************************************/uint16_t gui_match_get_fetter_id_bind(void);#endif

gui_match.c

/**********************************************************************对码绑定界面模块主文件*(c)copyright 2014,jdh*  All Right Reserved*新建时间:2014/10/24 by jdh*修改时间:2014/10/29 by jdh**********************************************************************//**********************************************************************头文件**********************************************************************/#include "gui_match.h"#include "cc1100.h"#include "gui_main.h"/**********************************************************************宏定义**********************************************************************/#define ID_FRAMEWIN            (GUI_ID_USER + 0x10)#define ID_BUTTON_OK            (GUI_ID_USER + 0x11)#define ID_BUTTON_CANCEL            (GUI_ID_USER + 0x12)#define ID_BUTTON_UP            (GUI_ID_USER + 0x13)#define ID_BUTTON_DOWN            (GUI_ID_USER + 0x14)#define ID_BUTTON_LEFT            (GUI_ID_USER + 0x15)#define ID_BUTTON_RIGHT            (GUI_ID_USER + 0x16)#define ID_TEXT_MATCH           (GUI_ID_USER + 0x17)#define ID_TEXT_ID           (GUI_ID_USER + 0x18)#define ID_TEXT_PROGBAR           (GUI_ID_USER + 0x19)#define ID_LISTBOX           (GUI_ID_USER + 0x1A)#define ID_PROGBAR           (GUI_ID_USER + 0x1B)/**********************************************************************列表框存储的数据数量**********************************************************************/#define LIST_LEN20/**********************************************************************数据结构**********************************************************************//**********************************************************************按键状态**********************************************************************/struct _Key_State{uint8_t ok;uint8_t cancel;uint8_t up;uint8_t down;uint8_t left;uint8_t right;};/**********************************************************************列表框缓存**********************************************************************/struct _List{uint8_t len;uint16_t buf[LIST_LEN];};/**********************************************************************静态变量**********************************************************************//**********************************************************************界面句柄**********************************************************************/static WM_HWIN Handle_Gui;/**********************************************************************资源表**********************************************************************/static const GUI_WIDGET_CREATE_INFO _aDialogCreate[] = {  { FRAMEWIN_CreateIndirect, "Frame3", ID_FRAMEWIN, 0, 0, 240, 320, 0, 0x0},  { BUTTON_CreateIndirect, "OK", ID_BUTTON_OK, 5, 255, 40, 20, 0, 0x0},  { BUTTON_CreateIndirect, "Button", ID_BUTTON_DOWN, 95, 280, 40, 20, 0, 0x0},  { BUTTON_CreateIndirect, "UP", ID_BUTTON_UP, 95, 255, 40, 20, 0, 0x0},  { BUTTON_CreateIndirect, "CANCEL", ID_BUTTON_CANCEL, 185, 255, 40, 20, 0, 0x0},  { BUTTON_CreateIndirect, "RIGHT", ID_BUTTON_RIGHT, 140, 270, 40, 20, 0, 0x0},  { BUTTON_CreateIndirect, "LEFT", ID_BUTTON_LEFT, 50, 270, 40, 20, 0, 0x0},  { TEXT_CreateIndirect, "Match", ID_TEXT_MATCH, 140, 15, 80, 20, 0, 0x0},  { TEXT_CreateIndirect, "ID", ID_TEXT_ID, 140, 40, 80, 20, 0, 0x0},  { TEXT_CreateIndirect, "", ID_TEXT_PROGBAR, 140, 65, 80, 20, 0, 0x0},  { LISTBOX_CreateIndirect, "Listbox", ID_LISTBOX, 5, 10, 120, 220, 0, 0x0},  { PROGBAR_CreateIndirect, "Progbar", ID_PROGBAR, 140, 85, 80, 20, 0, 0x0},  // USER START (Optionally insert additional widgets)  // USER END};/**********************************************************************上次工作时间**********************************************************************/static struct _Time Time_Last = {    .s = 0,    .ms = 0,    .us = 0};/**********************************************************************进度条开始的时间**********************************************************************/static struct _Time Time_Progbar = {    .s = 0,    .ms = 0,    .us = 0};/**********************************************************************接收CC1100的时间**********************************************************************/static struct _Time Time_Recv_CC1100 = {    .s = 0,    .ms = 0,    .us = 0};/**********************************************************************按键状态**********************************************************************/static struct _Key_State Key_State = {.ok = 0,.cancel = 0,.up = 0,.down = 0,.left = 0,.right = 0};/**********************************************************************当前显示状态*0:未显示,1显示**********************************************************************/static uint8_t State_Show = 0;/**********************************************************************进度条动画开始标志*0:终止,1:扫描,2:绑定**********************************************************************/static uint8_t Flag_Progbar = 0;/**********************************************************************列表框存储器**********************************************************************/static struct _List List = {.len = 0};/**********************************************************************已绑定脚镣ID*0:未绑定,其他:ID**********************************************************************/static uint16_t Fetter_Id_Bind = 0;/**********************************************************************静态函数**********************************************************************//**********************************************************************回调函数**********************************************************************/static void _cbDialog(WM_MESSAGE * pMsg);/**********************************************************************定时工作**********************************************************************/static void slot_tick(void);/**********************************************************************按键处理**********************************************************************/static void deal_key(void);/**********************************************************************进度条动画*参数:percent:百分比**********************************************************************/static void progbar_show(uint8_t percent);/**********************************************************************发送125k绑定信号**********************************************************************/static void emit_125k_bind(void);/**********************************************************************处理cc1100接收数据*参数:task:0:扫描,1:绑定**********************************************************************/static void deal_cc1100(uint8_t task);/**********************************************************************产生激发数据*参数:cmd:功能码*     data:产生的2字节激发数据**********************************************************************/static void generate_exciter_data(uint8_t cmd,uint8_t *data);/**********************************************************************函数**********************************************************************//**********************************************************************模块载入**********************************************************************/void gui_match_load(void){//新建界面Handle_Gui = GUI_CreateDialogBox(_aDialogCreate, GUI_COUNTOF(_aDialogCreate),  _cbDialog, WM_HBKWIN, 0, 0);gui_match_show(OFF);}/**********************************************************************模块运行**********************************************************************/void gui_match_run(void){struct _Time time;//判断当前是否显示if (State_Show == 0){return;}//判断当前是否处于扫描状态if (Flag_Progbar == 1){deal_cc1100(0);}else{//判断当前是否处于绑定状态if (Flag_Progbar == 2){deal_cc1100(1);}}    //得到当前时间    get_time(&time);    //判断是否到工作时间if (sub_time(time,Time_Last) >= INTERVAL_GUI_MATCH * 1000)    {        //更新时间        Time_Last = time;                //定时工作        slot_tick();    }}/**********************************************************************设置显示状态*参数:enable:0:关闭显示,1:打开显示**********************************************************************/void gui_match_show(uint8_t enable){WM_HWIN hItem;State_Show = enable;if (enable){//设置列表框为焦点hItem = WM_GetDialogItem(Handle_Gui, ID_LISTBOX);WM_SetFocus(hItem);WM_ShowWindow(Handle_Gui);}else{WM_HideWindow(Handle_Gui);}}/**********************************************************************得到当前的显示状态*返回:0:关闭显示,1:打开显示**********************************************************************/uint8_t gui_match_get_show(void){return State_Show;}/**********************************************************************得到绑定的脚镣id*返回:0:未绑定,其他:脚镣id**********************************************************************/uint16_t gui_match_get_fetter_id_bind(void){//return Fetter_Id_Bind;return 0x100;}/**********************************************************************定时工作**********************************************************************/static void slot_tick(void){uint32_t ms = 0;uint8_t percent = 0;WM_HWIN hItem;//按键处理deal_key();//判断当前进度条是否需要显示if (Flag_Progbar){//判断是否是扫描if (Flag_Progbar == 1){//判断激发信号是否结束if (inf_exciter_get_busy() == 0){//关闭激发模块电源inf_exciter_power(OFF);}}//判断是否到工作时间ms = sub_time(Time_Last,Time_Progbar) / 1000;if (ms < TIME_PROGBAR_GUI_MATCH){percent = ms * 100 / TIME_PROGBAR_GUI_MATCH;progbar_show(percent);}else{//结束进度条动画Flag_Progbar = 0;progbar_show(100);//文本:结束hItem = WM_GetDialogItem(Handle_Gui, ID_TEXT_PROGBAR);TEXT_SetFont(hItem, &GUI_FontHZ12);TEXT_SetText(hItem,"结束");}}}/**********************************************************************按键处理**********************************************************************/static void deal_key(void){WM_HWIN hItem;uint8_t index = 0;uint16_t id = 0;uint8_t data[3] = {0};//判断下键是否按下if (inf_key_detect_hold(KEY_DOWN)){if (Key_State.down == 0){Key_State.down = 1;//按键状态改变hItem = WM_GetDialogItem(Handle_Gui, ID_BUTTON_DOWN);BUTTON_SetState(hItem,BUTTON_STATE_HASFOCUS | BUTTON_STATE_PRESSED);//发送按键信号GUI_SendKeyMsg(GUI_KEY_DOWN, 1);}}else{if (Key_State.down == 1){Key_State.down = 0;//按键状态改变hItem = WM_GetDialogItem(Handle_Gui, ID_BUTTON_DOWN);BUTTON_SetState(hItem,BUTTON_STATE_HASFOCUS);}}//判断上键是否按下if (inf_key_detect_hold(KEY_UP)){if (Key_State.up == 0){Key_State.up = 1;//按键状态改变hItem = WM_GetDialogItem(Handle_Gui, ID_BUTTON_UP);BUTTON_SetState(hItem,BUTTON_STATE_HASFOCUS | BUTTON_STATE_PRESSED);//发送按键信号GUI_SendKeyMsg(GUI_KEY_UP, 1);}}else{if (Key_State.up == 1){Key_State.up = 0;//按键状态改变hItem = WM_GetDialogItem(Handle_Gui, ID_BUTTON_UP);BUTTON_SetState(hItem,BUTTON_STATE_HASFOCUS);}}//判断扫描键是否按下if (inf_key_detect_hold(KEY_OK) && (Flag_Progbar == 0)){if (Key_State.ok == 0){Key_State.ok = 1;//按键状态改变hItem = WM_GetDialogItem(Handle_Gui, ID_BUTTON_OK);BUTTON_SetState(hItem,BUTTON_STATE_HASFOCUS | BUTTON_STATE_PRESSED);//文本:开始扫描hItem = WM_GetDialogItem(Handle_Gui, ID_TEXT_PROGBAR);TEXT_SetFont(hItem, &GUI_FontHZ12);TEXT_SetText(hItem,"开始扫描");//开始扫描Flag_Progbar = 1;//保存当前时间get_time(&Time_Progbar);//打开125k电源inf_exciter_power(ON);//发送125k绑定信号emit_125k_bind();//清空列表框List.len = 0;hItem = WM_GetDialogItem(Handle_Gui, ID_LISTBOX);listbox_clear(hItem);}}else{if (Key_State.ok == 1){Key_State.ok = 0;//按键状态改变hItem = WM_GetDialogItem(Handle_Gui, ID_BUTTON_OK);BUTTON_SetState(hItem,BUTTON_STATE_HASFOCUS);}}//判断清除键是否按下if (inf_key_detect_hold(KEY_LEFT)){if (Key_State.left == 0){Key_State.left = 1;//按键状态改变hItem = WM_GetDialogItem(Handle_Gui, ID_BUTTON_LEFT);BUTTON_SetState(hItem,BUTTON_STATE_HASFOCUS | BUTTON_STATE_PRESSED);//清空列表框List.len = 0;hItem = WM_GetDialogItem(Handle_Gui, ID_LISTBOX);listbox_clear(hItem);}}else{if (Key_State.left == 1){Key_State.left = 0;//按键状态改变hItem = WM_GetDialogItem(Handle_Gui, ID_BUTTON_LEFT);BUTTON_SetState(hItem,BUTTON_STATE_HASFOCUS);}}//判断绑定键是否按下if (inf_key_detect_hold(KEY_RIGHT) && (Flag_Progbar == 0)){if (Key_State.right == 0){Key_State.right = 1;//按键状态改变hItem = WM_GetDialogItem(Handle_Gui, ID_BUTTON_RIGHT);BUTTON_SetState(hItem,BUTTON_STATE_HASFOCUS | BUTTON_STATE_PRESSED);//判断当前是否有项if (List.len == 0){return;}//得到脚镣idhItem = WM_GetDialogItem(Handle_Gui, ID_LISTBOX);index = LISTBOX_GetSel(hItem);if (index >= List.len){//清空列表框List.len = 0;hItem = WM_GetDialogItem(Handle_Gui, ID_LISTBOX);listbox_clear(hItem);return;}id = List.buf[index];//数据data[0] = 0;data[1] = 0;data[2] = 0;//等待可以发送while (cc1100_judge_tx() == 0);//发送对码绑定帧cc1100_tx(CMD_RF_BIND,id,data);//开始绑定Flag_Progbar = 2;//保存当前时间get_time(&Time_Progbar);//更新绑定的脚镣IDFetter_Id_Bind = 0;//更新文本hItem = WM_GetDialogItem(Handle_Gui, ID_TEXT_MATCH);TEXT_SetFont(hItem, &GUI_FontHZ12);TEXT_SetText(hItem,"未绑定脚镣");hItem = WM_GetDialogItem(Handle_Gui, ID_TEXT_ID);TEXT_SetFont(hItem, &GUI_FontHZ12);TEXT_SetText(hItem,"ID:0");//更新文本hItem = WM_GetDialogItem(Handle_Gui, ID_TEXT_PROGBAR);TEXT_SetFont(hItem, &GUI_FontHZ12);TEXT_SetText(hItem,"正在绑定");}}else{if (Key_State.right == 1){Key_State.right = 0;//按键状态改变hItem = WM_GetDialogItem(Handle_Gui, ID_BUTTON_RIGHT);BUTTON_SetState(hItem,BUTTON_STATE_HASFOCUS);}}//判断返回键是否按下if (inf_key_detect_hold(KEY_CANCEL) && (Flag_Progbar == 0)){if (Key_State.cancel== 0){Key_State.cancel = 1;//按键状态改变hItem = WM_GetDialogItem(Handle_Gui, ID_BUTTON_CANCEL);BUTTON_SetState(hItem,BUTTON_STATE_HASFOCUS | BUTTON_STATE_PRESSED);}}else{if (Key_State.cancel == 1){Key_State.cancel = 0;//按键状态改变hItem = WM_GetDialogItem(Handle_Gui, ID_BUTTON_CANCEL);BUTTON_SetState(hItem,BUTTON_STATE_HASFOCUS);//返回主界面gui_match_show(OFF);gui_main_show(ON);}}}/**********************************************************************进度条动画*参数:percent:百分比**********************************************************************/static void progbar_show(uint8_t percent){WM_HWIN hItem;//进度条显示hItem = WM_GetDialogItem(Handle_Gui, ID_PROGBAR);PROGBAR_SetValue(hItem,percent);}/**********************************************************************发送125k绑定信号**********************************************************************/static void emit_125k_bind(void) {uint8_t data[2] = {0};//生成激活数据generate_exciter_data(CMD_125K_BIND,data);//生成新的激发序列inf_exciter_generate_frame(data,2);//等待空闲while (inf_exciter_get_busy());//发送inf_exciter_start();}/**********************************************************************处理cc1100接收数据*参数:task:0:扫描,1:绑定**********************************************************************/static void deal_cc1100(uint8_t task){struct _Rx_Buf_CC1100 buf;WM_HWIN hItem;char str[20] = {0};buf = cc1100_get_rx_buf();//判断是否是最新帧if (compare_time(buf.time,Time_Recv_CC1100) != 2){return;}//保存时间Time_Recv_CC1100 = buf.time;if (task == 0){//判断功能码是否是上传脚镣ID帧if (buf.cmd != CMD_RF_UP_FETTER_ID){return;}//判断是否还有存储空间if (List.len >= LIST_LEN){return;}//更新数据List.buf[List.len++] = buf.src_id;sprintf(str,"%d",List.buf[List.len - 1]);//更新列表框hItem = WM_GetDialogItem(Handle_Gui, ID_LISTBOX);LISTBOX_AddString(hItem, str);return;}if (task == 1){//判断功能码是否是确认对码绑定if (buf.cmd != CMD_RF_ACK_BIND){return;}//更新绑定的脚镣IDFetter_Id_Bind = buf.src_id;//更新文本hItem = WM_GetDialogItem(Handle_Gui, ID_TEXT_MATCH);TEXT_SetFont(hItem, &GUI_FontHZ12);TEXT_SetText(hItem,"已绑定脚镣");hItem = WM_GetDialogItem(Handle_Gui, ID_TEXT_ID);TEXT_SetFont(hItem, &GUI_FontHZ12);sprintf(str,"ID:0x%x",Fetter_Id_Bind);TEXT_SetText(hItem,str);return;}}/**********************************************************************产生激发数据*参数:cmd:功能码*     data:产生的2字节激发数据**********************************************************************/static void generate_exciter_data(uint8_t cmd,uint8_t *data){uint8_t temp = 0;uint8_t check = 0;temp = cmd << 6;temp |= LOCAL_ID >> 4;data[0] = temp;temp = LOCAL_ID << 4;check = checksum4(data,2);temp |= check;data[1] = temp;}/**********************************************************************回调函数**********************************************************************/static void _cbDialog(WM_MESSAGE * pMsg) {WM_HWIN hItem;switch (pMsg->MsgId) {case WM_INIT_DIALOG:{//初始化窗体//增加小按键FRAMEWIN_AddCloseButton(pMsg->hWin, FRAMEWIN_BUTTON_RIGHT, 0);FRAMEWIN_AddMaxButton(pMsg->hWin, FRAMEWIN_BUTTON_RIGHT, 1);FRAMEWIN_AddMinButton(pMsg->hWin, FRAMEWIN_BUTTON_RIGHT, 2);FRAMEWIN_SetFont(pMsg->hWin, &GUI_FontHZ12);FRAMEWIN_SetText(pMsg->hWin,"对码绑定");//初始化列表框hItem = WM_GetDialogItem(pMsg->hWin, ID_LISTBOX);////设置内容//LISTBOX_SetFont(hItem, &GUI_FontHZ12);//LISTBOX_AddString(hItem, "0x10");//LISTBOX_AddString(hItem, "0x11");//LISTBOX_AddString(hItem, "0x12");//LISTBOX_AddString(hItem, "0x13");//LISTBOX_AddString(hItem, "0x14");//List.buf[0] = 0x10;//List.buf[1] = 0x11;//List.buf[2] = 0x12;//List.buf[3] = 0x13;//List.buf[4] = 0x14;//List.len = 5;//设置为焦点WM_SetFocus(hItem);SCROLLBAR_CreateAttached(hItem, SCROLLBAR_CF_VERTICAL);//初始化按键hItem = WM_GetDialogItem(pMsg->hWin, ID_BUTTON_OK);BUTTON_SetFont(hItem, &GUI_FontHZ12);BUTTON_SetText(hItem,"扫描");hItem = WM_GetDialogItem(pMsg->hWin, ID_BUTTON_CANCEL);BUTTON_SetFont(hItem, &GUI_FontHZ12);BUTTON_SetText(hItem,"返回");hItem = WM_GetDialogItem(pMsg->hWin, ID_BUTTON_UP);BUTTON_SetFont(hItem, &GUI_FontHZ12);BUTTON_SetText(hItem,"上");hItem = WM_GetDialogItem(pMsg->hWin, ID_BUTTON_DOWN);BUTTON_SetFont(hItem, &GUI_FontHZ12);BUTTON_SetText(hItem,"下");hItem = WM_GetDialogItem(pMsg->hWin, ID_BUTTON_LEFT);BUTTON_SetFont(hItem, &GUI_FontHZ12);BUTTON_SetText(hItem,"清除");hItem = WM_GetDialogItem(pMsg->hWin, ID_BUTTON_RIGHT);BUTTON_SetFont(hItem, &GUI_FontHZ12);BUTTON_SetText(hItem,"绑定");//初始化文本hItem = WM_GetDialogItem(pMsg->hWin, ID_TEXT_MATCH);TEXT_SetFont(hItem, &GUI_FontHZ12);TEXT_SetText(hItem,"未绑定脚镣");hItem = WM_GetDialogItem(pMsg->hWin, ID_TEXT_ID);TEXT_SetFont(hItem, &GUI_FontHZ12);TEXT_SetText(hItem,"ID:0");hItem = WM_GetDialogItem(pMsg->hWin, ID_TEXT_PROGBAR);TEXT_SetFont(hItem, &GUI_FontHZ12);TEXT_SetText(hItem,"结束");//初始化进度条hItem = WM_GetDialogItem(pMsg->hWin, ID_PROGBAR);PROGBAR_SetBarColor(hItem,0,GUI_RED);PROGBAR_SetBarColor(hItem,1,GUI_GREEN);break;}default:{WM_DefaultProc(pMsg);break;}}}