在STM32上如果不使用外部晶振,OSC_IN和OSC_OUT的接法
来源:互联网 发布:cheatmaker 源码 编辑:程序博客网 时间:2024/04/29 18:42
如果使用内部RC振荡器而不使用外部晶振,请按照下面方法处理:
1)对于100脚或144脚的产品,OSC_IN应接地,OSC_OUT应悬空。
2)对于少于100脚的产品,有2种接法:
2.1)OSC_IN和OSC_OUT分别通过10K电阻接地。此方法可提高EMC性能。
2.2)分别重映射OSC_IN和OSC_OUT至PD0和PD1,再配置PD0和PD1为推挽输出并输出'0'。此方法可以减小功耗并(相对上面2.1)节省2个外部电阻。
以下是在ST英文网站FAQ上抄下的详细解释:
1) In 100 and 144 packages, the OSC_IN /OSC_Out pins are a dedicated pins for HSE and mapped respectively on pins 12, 13 and pins 23, 24 for LQFP packages. Although, for BGA 100 and BGA 144 packages, they are mapped respectively on pins C1,D1 and pins D1,E1. In this case the recommended configuration is:
OSC_In pin must be connected to ground as it is always an input pin
OSC_Out must be left not connected as it is always an output pin.
2) In LQFP48 and LQFP64 packages, the OSC_IN/OSC_Out pins are mapped on pins 5,6 whereas in the VFQFPN36 package they are mapped on pins 2,3. However the PD0 and PD1 functionality can be remapped by software on these pins. There are two possible configurations:
Hardware configuration: Connect the OSC_IN/OSC_Out pins to ground through a 10K pull down resistors.
Software configuration: First, the OSC_IN/OSC_Out pins are left not connected on PCB layout. Then, remap the PD0 and PD1 functionality by software on these pins and configure the PD0/PD1 to Output push-pull forced to 0 logic level(Data Register = 0). This will maintain those I/Os to a fixed level minimizing Noise and external stress on these pins.
The software configuration is recommended to reduce the power consumption and saves cost by avoiding the use of external pull down resistors as the I/O is already connected to the ground internally. Whereas the hardware configuration is recommended to increase the EMC performance.
- 在STM32上如果不使用外部晶振,OSC_IN和OSC_OUT的接法
- 在STM32上如果不使用外部晶振,OSC_IN和OSC_OUT的接法
- 在STM32上如果不使用外部晶振,OSC_IN和OSC_OUT的接法
- STM32 OSC_IN和OSC_OUT的作用 和 各种接法
- STM32 OSC_IN跟OSC_OUT的作用 和 各种接法
- STM32不使用外部晶振的接法
- 把OSC_IN/OSC_OUT引脚作为GPIO端口PD0/PD1
- 如果在外部PHP文件使用joomla的类库
- STM32外部中断的使用
- STM32外部中断的使用
- STM32学习笔记之关于上拉电阻、上拉电阻的接法和使用
- STM32学习笔记之关于上拉电阻、上拉电阻的接法和使用
- STM32使用内部振荡器及其和外部晶体振荡器的区别
- STM32使用内部振荡器及其和外部晶体振荡器的区别
- STM32使用内部振荡器及其和外部晶体振荡器的区别
- 陀螺仪和加速度传感器 MPU6050 I2C在stm32上的使用
- IAR下stm32使用12M外部晶振
- STM32使用外部16MHZ晶振总结
- 每个程序员都必须遵守的编程原则
- oracle 导入导出文章
- Perl 标签语句
- 移动测试策略
- 7.4.2 使用聚合操作进行计算
- 在STM32上如果不使用外部晶振,OSC_IN和OSC_OUT的接法
- NetBeans项目框属性显示小技巧
- 安装苹果系统
- 打开相机、相册
- Eclipse 安装SVN、Maven插件
- Makefile(一)
- 学习之使用标签来标记资源
- 实验五
- PKG-CONFIG的使用