CCNP-ipv6下启用ospfv3,tunnle隧道技术实现v6到v4转换
来源:互联网 发布:淘宝钓鱼椅子图片价格, 编辑:程序博客网 时间:2024/05/18 03:20
by-小世界
http://redcisco.blog.163.com
实验拓扑图:
实验配置:
R1参考配置:
ipv6 unicast-routing
interface FastEthernet0/0
no ip address
ipv6 address 2001::1/64
ipv6 ospf 100 area 0
ipv6 router ospf 100
router-id 1.1.1.1
(//如果在R1上不手工指定router-id,ospf进程会在R1上的ipv4地址中找到一个,但是由于R1上没有ipv4的地址,所以就没有router-id,这是不行的,但是R2、R4就可以不指定;)
R2参考配置:R2#conf t
R2(config)#ipv6 unicast-routing
R2(config)#inter f0/0
R2(config-if)#ipv6 address 2001::2/64
R2(config-if)#no sh
R2(config-if)#inter f1/0ip add 23.1.1.2 255.255.255.0no sh
R2(config-if)#router eigrp 100//隧道技术两端的源和目的首先保证能够通信,所以启用IGP
R2(config-router)#no auto-summary
R2(config-router)#network 23.1.1.2 0.0.0.0
R2(config-router)#do show ipv6 inter bri
FastEthernet0/0 [up/up]
FE80::CE01:7FF:FE64:0
2001::2
FastEthernet1/0 [up/up]
R2(config)#inter tunnel 0
R2(config-if)#ipv6 address 2024::2/64//配置隧道接口的地址
R2(config-if)#tunnel source 23.1.1.2
R2(config-if)#tunnel destination ?
Hostname or A.B.C.D ip address or host name
X:X:X:X::X IPv6 address
R2(config-if)#tunnel destination 34.1.1.4
R2(config-if)#tunnel mode ?
aurp AURP TunnelTalk AppleTalk encapsulation
cayman Cayman TunnelTalk AppleTalk encapsulation
dvmrp DVMRP multicast tunnel
eon EON compatible CLNS tunnel
gre generic route encapsulation protocol
ipip IP over IP encapsulation
ipsec IPSec tunnel encapsulation
iptalk Apple IPTalk encapsulation
ipv6 Generic packet tunneling in IPv6
ipv6ip IPv6 over IP encapsulation
mpls MPLS encapsulations
nos IP over IP encapsulation (KA9Q/NOS compatible)
rbscp RBSCP in IP tunnel
R2(config-if)#tunnel mode ipv6ip //配置隧道的模式,默认为GRE
R2(config-if)#do p 2024::4
Sending 5, 100-byte ICMP Echos to 2024::4, timeout is 2 seconds:
!!!!!
R2(config)#ipv6 router ospf 100
R2(config-rtr)#router-id 2.2.2.2
R2(config-rtr)#inter f0/0
R2(config-if)#ipv6 ospf 100 area 0
R2(config-if)#inter tunn 0
R2(config-if)#ipv6 ospf 100 area 0
R3参考配置:
interface FastEthernet0/0ip address 23.1.1.3 255.255.255.0
interface FastEthernet1/0 ip address 34.1.1.3 255.255.255.0
router eigrp 100
network 23.1.1.3 0.0.0.0
network 34.1.1.3 0.0.0.0
no auto-summary
R4参考配置:R4#conf t
R4(config)#ipv6 unicast-routing
R4(config)#inter f0/0ip add 34.1.1.4 255.255.255.0no sh
R4(config-if)#inter f1/0
R4(config-if)#ipv6 address 2002::4/64
R4(config-if)#no sh
R4(config-if)#router ei 100
R4(config-router)#no auto-summary
R4(config-router)#network 34.1.1.4 0.0.0.0
R4(config-router)#do pi 23.1.1.2
Sending 5, 100-byte ICMP Echos to 23.1.1.2, timeout is 2 seconds:
!!!!!
R4(config)#inter tunnel 0
R4(config-if)#ipv6 address 2024::4/64
R4(config-if)#no sh
R4(config-if)#tunnel source 34.1.1.4
R4(config-if)#tunnel destination 23.1.1.2
R4(config-if)#tunnel mode ipv6ip
R4(config)#ipv6 router ospf 100
R4(config-rtr)#router-id 4.4.4.4
R4(config)#inter tunnel 0
R4(config-if)#ipv6 ospf 100 area 0
R4(config-if)#inter f1/0
R4(config-if)#ipv6 ospf 100 area 0
也可以通过路由表查看:
R4#show ipv6 route
IPv6 Routing Table - 7 entries
O 2001::/64 [110/11112]
via FE80::1701:102, Tunnel0
C 2002::/64 [0/0]
via ::, FastEthernet1/0
L 2002::4/128 [0/0]
via ::, FastEthernet1/0
C 2024::/64 [0/0]
via ::, Tunnel0
L 2024::4/128 [0/0]
via ::, Tunnel0
L FE80::/10 [0/0]
via ::, Null0
L FF00::/8 [0/0]
via ::, Null0
R4#
R5参考配置:R5#conf tR5(config)#ipv6 unicast-routing
R5(config)#inter f0/0
R5(config-if)#ipv6 address 2002::5/64
R5(config-if)#do show ipv inter bri
FastEthernet0/0 [up/up]
FE80::CE04:15FF:FE1C:0
2002::5
R5(config-if)#ipv6 router ospf 100
R5(config-rtr)#router-id 5.5.5.5
R5(config)#inter f0/0
R5(config-if)#ipv6 ospf 100 area 0
*Mar 1 00:24:21.859: %OSPFv3-5-ADJCHG: Process 100, Nbr 4.4.4.4 on FastEthernet0/0 from LOADING to FULL, Loading Done
实验测试:
R5#ping 2001::1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 2001::1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 68/108/160 ms
理解效果配置图:
实验总结:
1.Tunnel(隧道)接口是系统虚拟的接口,用来实现标准的点对点的传输,必须在两端进行配置。
2.IPv6 over IPv4隧道机制是在IPv6数据包前封装上IPv4的包头,通过隧道使IPv6数据包穿越IPv4网络,实现隔离的IPv6网络的互通;即在IPv4网络中通过隧道技术传输IPv6流量要求边缘路由器将IPv6报文封装至IPv4报文中,而在另一端的路由器将之解封装。
3.如果在交换机上启用IPv6路由功能,首先要做如下配置:
SW1(config)#sdm prefer dual-ipv4-and-ipv6 routing
SW1#reload //重启后,才能支持IPv4和IPv6路由功能
SW1(config)#ipv6 unicast-routing //启用IPv6路由功能
4.请参考http://blog.sina.com.cn/s/blog_635e1a9e01019009.html,谢谢LZ。
5.如果模拟器link-local一致,请修改本地链路地址,方法ipv6 address FE80::5 link-local。
感谢Node汤sir!
0 0
- CCNP-ipv6下启用ospfv3,tunnle隧道技术实现v6到v4转换
- windows7 关闭和启用IPV6隧道适配器
- windows7 关闭和启用IPV6隧道适配器
- isatap ipv6隧道技术原理
- 【IPv6】ISATAP隧道技术详解
- IPv6 over IPv4隧道技术
- 【IPv6】ISATAP隧道技术详解
- CCNA(新版)-ipv6网络中启用-ospfv3路由协议配置实验
- HUAWEI CE6870 IPv6 OSPFv3 配置
- WIN7下关闭IPV6隧道适配器命令
- ip过度之ipv6 to ipv4 隧道技术
- Linux下的IPv6地址、路由以及隧道配置
- ubuntu下ipv6的配置(isatap隧道模式)问题?
- Linux下的IPv6地址、路由以及隧道配置
- linux下ipv6实验环境的搭建(隧道)
- Linux下的IPv6地址、路由以及隧道配置
- Linux下的IPv6地址、路由以及隧道配置
- Linux下的IPv6地址、路由以及隧道配置
- CCNP-BGP选路实验,考察BGP属性:Local-prf和MED
- CCNP-EBGP环回口建立邻居之间启用IGP的效果
- CCNP-BGP选路实验,考察BGP属性:公认必选之AS-path
- java中的集合存储结构
- CCNP-BGP选路,BGP属性:公认必选之Origin、Next-hop
- CCNP-ipv6下启用ospfv3,tunnle隧道技术实现v6到v4转换
- RSA算法原理(二)
- CCNP-EIGRP&OSPF重分布时开销metric值的计算过程
- CCNP-双向重分布-OSPF&rip实验
- 抓取远程网页并解析HTML
- CCNP-多域多点双向重分布实验distance&route-map(1)
- CCNP-SLA服务等级协议service level agreement&track
- CCNP-多域多点双向重分布实验distance&route-map(2)
- CCNP-Policy Basic Route:PBR策略路由