CISCO switches change the VTP modeautomatically from client to transparent
来源:互联网 发布:如何更改淘宝店铺名字 编辑:程序博客网 时间:2024/05/25 08:13
Some CatalystLayer 2 and Layer 3 fixed configuration switches change the VTP modeautomatically from client to transparent with this error message:
%SW_VLAN-6-VTP_MODE_CHANGE: VLAN managerchanging device mode from
CLIENT to TRANSPARENT.
Either of thesetwo reasons can cause the automatic VTP mode change in these switches:
· More VLANsrun on the Spanning Tree Protocol (STP) than the switch can support.
CatalystLayer 2 and Layer 3 fixed configuration switches support a different maximumnumber of instances of STP with the use of per-VLAN spanning tree+ (PVST+). Forexample, the Catalyst 2940 supports four instances of STP in PVST+ mode, whilethe Catalyst 3750 supports 128 instances of STP in PVST+ mode. If more than themaximum number of VLANs is defined in the VTP, the VLANs that remain operatewith STP disabled.
If the number of instances of STP that is already in use is greater thanthe maximum number, you can disable STP on one of the VLANs and enable it onthe VLAN where you want STP to run. Issue the no spanning-tree vlan vlan-id globalconfiguration command in order to disable STP on a specific VLAN. Then, issuethe spanning-tree vlan vlan-id global configuration command in order to enableSTP on the desired VLAN.
Note: Switches that do not run STP stillforward the bridge protocol data units (BPDUs) that they receive. In this way,the other switches on the VLAN that have a running STP instance can breakloops. Therefore, STP must run on enough switches in order to break all theloops in the network. For example, at least one switch on each loop in the VLANmust run STP. You do not need to run STP on all switches in the VLAN. However,if you run STP only on a minimal set of switches, a change to the network canintroduce a loop into the network and can result in a broadcast storm.
Workarounds:
· Reduce the number of VLANs that areconfigured to a number that the switch supports.
· Configure the IEEE 802.1s MultipleSTP (MSTP) on the switch in order to map multiple VLANs to a single STPinstance.
· Use switches and/or images (EnhancedImage [EI]) which support a greater number of VLANs.
· The switch receives more VLANs from a connectedswitch than the switch can support.
An automaticVTP mode change also can occur if the switch receives a VLAN configurationdatabase message that contains more than a set number of VLANs. This normallyhappens in Catalyst Layer 2 and Layer 3 fixed configuration switches when they areconnected to a VTP domain that has more VLANs than are supported locally.
Workarounds:
· Configure the allowed VLAN list onthe trunk port of the connected switch in order to restrict the number of VLANsthat are passed to the client switch.
· Enable pruning on the VTP serverswitch.
· Use switches and/or images (EI) whichsupport a greater number of VLANs.
- CISCO switches change the VTP modeautomatically from client to transparent
- vtp mode {server| client | transparent}三种模式详解
- Is it possible to change Agile Web Client login from port 7001 to the default port 80 in Weblogic?
- Mikrotik Switches Vs Cisco Switches
- Configure IOS Catalyst Switches to Connect Cisco IP Phones Configuration
- Have You Upgraded to Cisco Nexus 9000 Series Switches?
- ubuntu: change the path from openjdk to oracle jdk
- VTP:Cisco VLAN Trunking Protocol
- (原)Cisco VTP协议
- Client requested master to start replication from impossible position; the last event was read from
- How do I change the FROM address to a friendly name?
- Android编译错误:You have tried to change the API from what has been previously approved.
- You have tried to change the API from what has been previously approved.
- You have tried to change the API from what has been previously approved
- pyqt - How to change the color of a word from my textedit
- Android编译错误:You have tried to change the API from what has been previously approved.
- Android编译错误:You have tried to change the API from what has been previously approved.
- How to change the dbo
- 安卓UI控件1
- Spring+Mybatis整合事务不起作用之解决方案汇总
- iPhone 开发中 Duplicate interface definition for class’*'怎么处理那?
- system调用导致子进程socket句柄泄漏问题分析
- Linux文件系统新增1--用户管理
- CISCO switches change the VTP modeautomatically from client to transparent
- webview.addJavascriptInterface() doen not work on API 16+
- Scala基础教程(二):数据类型、变量
- 多列radiogroup
- 手把手教你轻松实现listview下拉刷新
- iOS9下修改回HTTP模式进行网络请求
- 【C++设计技巧】C++中的RAII机制
- Scala基础教程(三):访问修饰符、运算符
- 一起来说 Vim 语