自定制openwrt启动提示no TP-Link header found
来源:互联网 发布:翻译官软件下载 编辑:程序博客网 时间:2024/06/04 17:44
最近在定制openwrt时,发现一个奇怪的问题,自己一直的openwrt提示,升级之后,提示spi0.0: no TP-Link header found,由于以前没有研究过openwrt,
********************************************** U-Boot 1.1.4 (Sep 30 2015, 16:19:33) **********************************************QXNET E600G (QCA953x) U-BootDRAM: 16bit ddr2 64 MB SDRAMFLASH: Winbond W25Q128 (16 MB)LED on during eth initialization...eth0 upeth1 upHit any key to stop autoboot: 0 Booting image at: 0x9F040000 Image name: OpenWrt r48549 Image type: MIPS Linux Kernel Image (lzma compressed) Data size: 1057092 Bytes = 1 MB Load address: 0x80060000 Entry point: 0x80060000Uncompressing kernel image... OK!Starting kernel...[ 0.000000] Linux version 3.10.49 (linux@linux-virtual-machine) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r48549) ) #2 Fri Apr 29 08:55:54 CST 2016[ 0.000000] bootconsole [early0] enabled[ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)[ 0.000000] SoC: Qualcomm Atheros QCA9533 rev 2[ 0.000000] Clocks: CPU:650.000MHz, DDR:390.771MHz, AHB:216.666MHz, Ref:25.000MHz[ 0.000000] Determined physical RAM map:[ 0.000000] memory: 04000000 @ 00000000 (usable)[ 0.000000] Initrd not found or empty - disabling initrd[ 0.000000] Zone ranges:[ 0.000000] Normal [mem 0x00000000-0x03ffffff][ 0.000000] Movable zone start for each node[ 0.000000] Early memory node ranges[ 0.000000] node 0: [mem 0x00000000-0x03ffffff][ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256[ 0.000000] Kernel command line: board=E600G console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)[ 0.000000] Writing ErrCtl register=00000000[ 0.000000] Readback ErrCtl register=00000000[ 0.000000] Memory: 61272k/65536k available (2239k kernel code, 4264k reserved, 603k data, 228k init, 0k highmem)[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1[ 0.000000] NR_IRQS:51[ 0.000000] Calibrating delay loop... 432.53 BogoMIPS (lpj=2162688)[ 0.050000] pid_max: default: 32768 minimum: 301[ 0.050000] Mount-cache hash table entries: 512[ 0.060000] NET: Registered protocol family 16[ 0.070000] MIPS: machine is E600G[ 0.080000] ar724x-pci ar724x-pci.0: PCIe link is down[ 0.080000] registering PCI controller with io_map_base unset[ 0.090000] ar71xx: invalid MDIO id 1[ 0.500000] bio: create slab <bio-0> at 0[ 0.500000] PCI host bridge to bus 0000:00[ 0.510000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x11ffffff][ 0.510000] pci_bus 0000:00: root bus resource [io 0x0000][ 0.520000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff][ 0.520000] Switching to clocksource MIPS[ 0.530000] NET: Registered protocol family 2[ 0.530000] TCP established hash table entries: 512 (order: 0, 4096 bytes)[ 0.540000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)[ 0.550000] TCP: Hash tables configured (established 512 bind 512)[ 0.550000] TCP: reno registered[ 0.560000] UDP hash table entries: 256 (order: 0, 4096 bytes)[ 0.560000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)[ 0.570000] NET: Registered protocol family 1[ 0.590000] squashfs: version 4.0 (2009/01/31) Phillip Lougher[ 0.590000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.[ 0.610000] msgmni has been set to 119[ 0.610000] io scheduler noop registered[ 0.610000] io scheduler deadline registered (default)[ 0.620000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled[ 0.650000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A[ 0.650000] console [ttyS0] enabled, bootconsole disabled[ 0.650000] console [ttyS0] enabled, bootconsole disabled[ 0.670000] ath79-spi ath79-spi: master is unqueued, this is deprecated[ 0.670000] m25p80 spi0.0: found w25q128, expected m25p80[ 0.680000] m25p80 spi0.0: w25q128 (16384 Kbytes)[ 0.690000] spi0.0: no TP-Link header found[ 0.710000] libphy: ag71xx_mdio: probed[ 1.270000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd042, driver=Generic PHY][ 1.280000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII[ 1.840000] ag71xx-mdio.1: Found an AR934X built-in switch[ 2.870000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII[ 2.880000] TCP: cubic registered[ 2.880000] NET: Registered protocol family 17[ 2.890000] 8021q: 802.1Q VLAN Support v1.8[ 2.890000] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6[ 2.900000] Please append a correct "root=" boot option; here are the available partitions:[ 2.910000] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
修改target/linux/ar71xx/files/drivers/mtd中的分区信息中的
#define TPLINK_KERNEL_OFFS 0x40000
此处的TPLINK_KERNEL_OFFS为FLASH中分区存放地址。
0 0
- 自定制openwrt启动提示no TP-Link header found
- TP-LINK-WR703N & Openwrt
- TP-LINK TL-WR703N OpenWRT 12.09 从U盘启动
- openwrt--tp-link w703r配置
- TP-LINK WR703N OpenWrt刷机教程
- TP-LINK WR703N OpenWrt刷机教程
- TP-Link TL-WDR4310 刷openwrt
- [OpenWrt] tp-link wr703n刷openwrt挂载u盘攻略
- openwrt开机自启动
- openwrt-添加自启动
- openwrt添加自启动
- openwrt程序自启动
- archlinux在虚拟机VMWare启动图形界面提示no screen found
- Using OpenWRT on TP-Link WR841N-V7.2 router
- TP-LINK WR703N把OpenWrt挂载u盘教程
- TP-Link 703N刷OpenWrt的实践
- TP link 703N 刷openwrt+挂载USB 摄像头
- 编译适用于TP-Link WR703N的OpenWRT固件
- 可变参数列表
- 【CodeChef-ANUDTQ】Dynamic Trees and Queries【Splay】【DFS序】
- ikev2 配置
- How far away ?
- macbookpro 拆卸或安装内存
- 自定制openwrt启动提示no TP-Link header found
- Dubbo-zookeeper的部署和安装
- centOS里升级python
- C# 使用mysql.data.dll,读写mysql数据库
- MongoDB-基本命令学习一
- POJ-1679-The Unique MST(次小生成树)
- C++输入输出运算符重载
- YAML 技术研究
- 【Android动画九章】-LayoutAnimationController