HDMI采集芯片 ADV7611采集PC数据调试总结

开发环境：TI DM365 平台， ADV7611采集板， CCS5.5

第一步：I2C调通

这张是 ADV7611 读写的时序图，可以看出在写和读的时候发送地址数据的时候的停止位信息是不同的，在写的时候是不需要停止位的，但是读的时候是要停止位的。如果I2C在硬件没问题的时候可以考虑是不是这方面的问题。

第二步：map 配置：

根据官方推荐配置进行配置：

  0x98, 0xFF, 0x80,    // I2C reset0x98, 0xF4, 0x80,// CEC SLAVE ADDRESS0x98, 0xF5, 0x7C,// INFOFRAME SLAVE ADDRESS0x98, 0xF8, 0x4C,// DPLL SLAVE ADDRESS0x98, 0xF9, 0x64,// KSV SLAVE ADDRESS0x98, 0xFA, 0x6C,// EDID SLAVE ADDRESS0x98, 0xFB, 0x68,// HDMI SLAVE ADDRESS0x98, 0xFD, 0x44,// CP SLAVE ADDRESS

第三步：EDID 

EDID里面主要是定义了这显示设备所支持的图像分辨率，支持的声音格式，声音通道，及3D等等，其目的是告诉外接设备我所支持的特性，让外接设备输出一个我所支持的timing，否则外接设备输出的timing并不支持的话那就没有图像，声音的显示了。ADV7611 在上电后需要配置 EDID 使得输出端读取EDID 的内容然后配置相应的输出，下面是相应的EDID 配置：

unsigned char vga_edid[256]=   {0x00, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0x00, //000x06, 0x8F, 0x07, 0x11, 0x01, 0x00, 0x00, 0x00, //080x17, 0x11, 0x01, 0x03, 0x80, 0x0C, 0x09, 0x78, //100x0A, 0x1E, 0xAC, 0x98, 0x59, 0x56, 0x85, 0x28, //180x29, 0x52, 0x57, 0x00, 0x00, 0x00, 0x01, 0x01, //200x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x01, //280x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x8C, 0x0A, //300xD0, 0x8A, 0x20, 0xE0, 0x2D, 0x10, 0x10, 0x3E, //380x96, 0x00, 0x81, 0x60, 0x00, 0x00, 0x00, 0x18, //400x01, 0x1D, 0x80, 0x18, 0x71, 0x1C, 0x16, 0x20, //480x58, 0x2C, 0x25, 0x00, 0x81, 0x49, 0x00, 0x00, //500x00, 0x9E, 0x00, 0x00, 0x00, 0xFC, 0x00, 0x56, //580x41, 0x2D, 0x31, 0x38, 0x30, 0x39, 0x41, 0x0A, //600x20, 0x20, 0x20, 0x20, 0x00, 0x00, 0x00, 0xFD, //680x00, 0x17, 0x3D, 0x0D, 0x3E, 0x11, 0x00, 0x0A, //700x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x01, 0x1C, //780x02, 0x03, 0x34, 0x71, 0x4D, 0x82, 0x05, 0x04,   //800x01, 0x10, 0x11, 0x14, 0x13, 0x1F,0x06, 0x15,  //880x03, 0x12, 0x35, 0x0F, 0x7F, 0x07,0x17, 0x1F,0x38, 0x1F, 0x07, 0x30, 0x2F, 0x07,0x72, 0x3F,0x7F, 0x72, 0x57, 0x7F, 0x00, 0x37,0x7F, 0x72,0x83, 0x4F, 0x00, 0x00, 0x67, 0x03,0x0C, 0x00,0x10, 0x00, 0x88, 0x2D, 0x00, 0x00,0x00, 0xFF,0x00, 0x0A, 0x20, 0x20, 0x20, 0x20,0x20, 0x20,0x20, 0x20, 0x20, 0x20, 0x20, 0x20,0x00, 0x00,0x00, 0xFF, 0x00, 0x0A, 0x20, 0x20,0x20, 0x20,0x20, 0x20, 0x20, 0x20, 0x20, 0x20,0x20, 0x20,0x00, 0x00, 0x00, 0xFF, 0x00, 0x0A,0x20, 0x20,0x20, 0x20, 0x20, 0x20, 0x20, 0x20,0x20, 0x20,0x20, 0x20, 0x00, 0x00, 0x00, 0x00,0x00, 0x00,0x00, 0x00, 0x00, 0x00, 0x00, 0x00,0x00, 0x00,0x00, 0x00, 0x00, 0x00, 0x00, 0x00,0x00, 0xDA,}；void i2c_program_edid(unsigned char *data, int length){unsigned long i;ADV7611_Write(0x64, 0x77, 0x00);ADV7611_Write(0x64, 0x74, 0x00);for (i=0; i<length; i++)ADV7611_Write(0x6C, i, data[i]);for (i=0; i<800000; i++); // delay for HPAADV7611_Write(0x64, 0x77, 0x00);ADV7611_Write(0x64, 0x52, 0x20);ADV7611_Write(0x64, 0x53, 0x00);ADV7611_Write(0x64, 0x70, 0x9E);ADV7611_Write(0x64, 0x74, 0x01);}

第四步:其他参数配置

0x98, 0x00, 0x02,0x98, 0x01, 0x05,0x98, 0x02, 0xF5,// Auto CSC, no YPbPr colorspace conversion,// set the output range of the digital data = limited range (16 to 235), YCrCb out0x98, 0x03, 0x20,// 0x80 = 16-bit ITU-656 SDR mode; 0x20 = 8-bit 4:2:2 DDR mode (ITU-656 mode)0x98, 0x04, 0x62,// 011 - P[23:16] V/R, P[15:8] Y/G, P[7:0] U/CrCb/B ; XTAL = 28.868 MHz0x98, 0x05, 0x28,// DE output on the FIELD/DE pin ; AV Codes Off// 0x98, 0x06, 0xA0,//0x98, 0x0B, 0x44,// Powers up CP and digital sections of HDMI block; Powers up XTAL buffer to the digital core0x98, 0x0C, 0x42,// Chip is operational,Disables power save mode,Powers up the clock to the CP core,Powers up the pads of the digital output pins0x98, 0x14, 0x7F,// High drive strength of data output drivers;output pixel clock out signal on the LLC pin,                    // synchronization pins, HS, VS/FIELD, FIELD/DE;audio output interface pins (AP0, AP1/I2S_TDM, AP2 ... AP5).0x98, 0x15, 0x80,// Disable Tristate of Pins// 0x98, 0x19, 0x83,// LLC DLL phase0x98, 0x19, 0xca,// LLC DLL phase// 0x98, 0x19, 0xCA,// LLC DLL phase// 0x98, 0x19, 0x8A,// LLC DLL phase0x98, 0x33, 0x40,// LLC DLL enable0x44, 0xBA, 0x01,// Set HDMI FreeRun when the TMDS clock is not detected on the selected HDMI port// 0x44, 0x3E, 0x01,0x64, 0x00, 0x40,0x64, 0x40, 0x81,// Disable HDCP 1.1 features0x68, 0x9B, 0x03,// ADI recommended setting0x68, 0xC1, 0x01,// ADI recommended setting0x68, 0xC2, 0x01,// ADI recommended setting0x68, 0xC3, 0x01,// ADI recommended setting0x68, 0xC4, 0x01,// ADI recommended setting0x68, 0xC5, 0x01,// ADI recommended setting0x68, 0xC6, 0x01,// ADI recommended setting0x68, 0xC7, 0x01,// ADI recommended setting0x68, 0xC8, 0x01,// ADI recommended setting0x68, 0xC9, 0x01,// ADI recommended setting0x68, 0xCA, 0x01,// ADI recommended setting0x68, 0xCB, 0x01,// ADI recommended setting0x68, 0xCC, 0x01,// ADI recommended setting0x68, 0x00, 0x00,// Set HDMI Input Port A0x68, 0x83, 0xFE,// Enable clock terminator for port A0x68, 0x6F, 0x0C,// ADI recommended setting0x68, 0x85, 0x1F,// ADI recommended setting0x68, 0x87, 0x70,// ADI recommended setting0x68, 0x8D, 0x04,// LF gain equalizer settings for dynamic mode range 10x68, 0x8E, 0x1E,// HF gain equalizer settings for dynamic mode range 10x68, 0x1A, 0x8A,// unmute audio0x68, 0x57, 0xDA,// ADI recommended setting0x68, 0x58, 0x01,// ADI recommended setting0x68, 0x03, 0x98,    // DIS_I2C_ZERO_COMPR0x68, 0x75, 0x10,// DDC drive strength

这个配置是yuv4:2:2 8bit的配置