LTE Protocol PICS
来源：互联网 发布：什么是数据双活 编辑：程序博客网 时间：2024/05/08 11:09
Test Spec 3GPP TS 36.523-2 V13.0.0 Table A.4.1-1 UE Radio Technologies Reference Release Status Supported Allowed Comments1 E-UTRA FDD 36.101 Rel-8 yes yes, no 2 E-UTRA TDD 36.101 Rel-8 yes yes, no 3 HRPD C.S0024-A Rel-8 no yes, no 4 1xRTT C.S0002-A Rel-8 no yes, no 5 WLAN IEEE Std 802.11 yes yes, no 6 UTRA 21.904, 5 R99 yes yes, no 7 GERAN 21.904, 5 R99 yes yes, no Table A.4.1-2 UE general functionality Reference Release Status Supported Allowed Comments1 Support of multiple E-UTRA FDD bands 36.101, 5.5 Rel-8 yes yes, no 2 Support of multiple E-UTRA TDD bands 36.101, 5.5 Rel-8 yes yes, no Table A.4.2.1.1-1 Definition of Bearer Services Reference Release Status Supported Allowed Comments1 Support of CS fallback 24.301 Rel-8 yes yes, no "The UE supports CS fallback for voice calls. If true, [8] pc_CS and at least one of pc_FDD, pc_TDD_HCR, pc_TDD_LCR, pc_TDD_VHCR or pc_UMTS_GSM is also true.If pc_CS_fallback is true, pc_SMS_SGs shall be set to true A UE with the voice domain preference set to CS Voice only or IMS PS voice preferred, CS Voice as secondary or CS voice preferred, IMS PS Voice as secondary shall set this PICS to true."2 Support of SMS over SGs 24.301 Rel-8 yes yes, no "The UE supports SMS over SGs and is configured for SMS over SGs.If it is set to true, and at least one of pc_SMS_SGs_MT and pc_SMS_SGs_MO is true.If it is set to true, pc_combined_attach shall be set to true"3 Support of 1xCS fallback 24.301 Rel-8 no yes, no 4 Support of IMS emergency call 22.101 Rel-9 no yes, no For Rel-9 or later releases: mandatory for UEs which supports IMS speech.5 Support of eMBMS 36.331 Rel-9 no yes, no The UE supports eMBMS.6 Support of Enhanced 1xCS fallback 23.272 Rel-9 no yes, no 7 Support of eMBMS service continuity "36.306, 6.3.1(Note 2)" Rel-11 no yes, no The UE supports eMBMS service continuity.8 Supports Offload to/from WLAN and supports S2b "36.304, 5.6.224.302, 6.10.4" Rel-12 no yes, no 9 Support of DC Split DRB 36.306, 4.3.20.1 Rel-12 no yes, no The UE supports dual connectivity and DRB type of Split bearer.10 Support of DC SCG DRB 36.306, 4.3.20.2 Rel-12 no yes, no The UE supports dual connectivity and DRB type of SCG bearer.Note "Note 1: A UE may support one or more of bearer service 1, 2, 3, 4 or 5.Note 2: See [19] subclause 17.4 for general assumptions of the MBMS service Continuity test cases." Table A.4.3-1 Supported protocols Reference Release Status Supported Allowed Comments1 EPS Mobility Management 24.301, 5 Rel-8 yes yes, no 2 EPS Session Management 24.301, 6 Rel-8 yes yes, no 3 Radio Resource Control 36.331 Rel-8 yes yes, no 4 Packet Data Convergence Protocol 36.323 Rel-8 yes yes, no 5 Radio Link Control 36.322 Rel-8 yes yes, no 6 Medium Access Control 36.321 Rel-8 yes yes, no 7 Physical Layer 36.201 Rel-8 yes yes, no Table A.4.3-2 Special Conformance Testing Functions Reference Release Status Supported Allowed Comments1 UE test loop 36.509 Rel-8 yes yes, no 2 Max UE test loop UL RLC SDU size 65535 bits 36.509 Rel-8 yes yes, no 3 Update UE Location Information 36.509, cl 5.1 Rel-10 no yes, no Table A.4.3.1-1 FDD RF Baseline Implementation Capabilities Reference Release Status Supported Allowed Comments1 Frequency band: 1920-1 980, 2110-2170 MHz 36.101, 5.5 Rel-8 yes yes, no Band 12 Frequency band: 1850-1910, 1930-1 990 MHz 36.101, 5.5 Rel-8 no yes, no Band 23 Frequency band: 1710-1785, 1805-1880 MHz 36.101, 5.5 Rel-8 yes yes, no Band 34 Frequency band: 1710-1755, 2110-2155 MHz 36.101, 5.5 Rel-8 no yes, no Band 45 Frequency band: 824 – 849, 869-894 MHz 36.101, 5.5 Rel-8 yes yes, no Band 56 Frequency band: 830-840, 875-885 MHz 36.101, 5.5 Rel-8 no yes, no Band 67 Frequency band: 2500-2570, 2620-2690 MHz 36.101, 5.5 Rel-8 yes yes, no Band 78 Frequency band: 880–915, 925–960 MHz 36.101, 5.5 Rel-8 yes yes, no Band 89 Frequency band: 1749.9-1784.9, 1844.9-1879.9 MHz 36.101, 5.5 Rel-8 no yes, no Band 910 Frequency band: 1710-1770, 2110-2170 MHz 36.101, 5.5 Rel-8 no yes, no Band 1011 Frequency band: 1427.9-1452.9, 1475.9-1500.9 MHz 36.101, 5.5 Rel-8 no yes, no Band 1112 Frequency band: 699-716, 729-746 MHz 36.101, 5.5 Rel-8 no yes, no Band 1213 Frequency band: 777–787, 746–756 MHz 36.101, 5.5 Rel-8 no yes, no Band 1314 Frequency band: 788-798, 758-768 MHz 36.101, 5.5 Rel-8 no yes, no Band 1415 Reserved no yes, no 16 Reserved no yes, no 17 Frequency band: 704716, 734-746 MHz 36.101, 5.5 Rel-8 no yes, no Band 1718 Frequency band: 815-830, 860-875 MHz 36.101, 5.5 Rel-9 no yes, no Band 1819 Frequency band: 830–845, 875–890 MHz 36.101, 5.5 Rel-9 no yes, no Band 1920 Frequency band: 832-862, 791-821 MHz 36.101, 5.5 Rel-9 no yes, no Band 2021 Frequency band: 1447.9-1462.9, 1495.9-1510.9 MHz 36.101, 5.5 Rel-9 no yes, no Band 2122 Frequency band: 3410-3490, 3510-3590 MHz 36.101, 5.5 Rel-10 no yes, no Band 2223 Frequency band: 2000-2020, 2180-2200 MHz 36.101, 5. 5 Rel-10 no yes, no Band 2324 Frequency band: 1626.5-1660.5, 1525-1559 MHz 36.101, 5. 5 Rel-10 no yes, no Band 2425 Frequency band: 1850-1915, 1930-1995 MHz 36.101, 5. 5 Rel-10 no yes, no Band 2526 Frequency band: 814-849, 859-894 MHz 36.101, 5. 5 Rel-11 no yes, no Band 2627 Frequency band: 807-824, 852-869 MHz 36.101, 5. 5 Rel-11 no yes, no Band 2728 Frequency band: 703-748, 758-803 MHz 36.101, 5. 5 Rel-11 yes yes, no Band 2829 Frequency band: N/A, 717-728 MHz 36.101, 5. 5 Rel-11 no yes, no Band 2930 Frequency band: 2305-2315, 2350-2360 MHz 36.101, 5. 5 Rel-12 no yes, no Band 3031 Frequency band: 452.5-457.5, 462.5-467.5 MHz 36.101, 5. 5 Rel-12 no yes, no Band 3132 Frequency band: N/A, 1452-1496 MHz 36.101, 5. 5 Rel-12 no yes, no Band 32Table A.4.3.1-2 TDD RF Baseline Implementation Capabilities Reference Release Status Supported Allowed Comments1 Frequency band: 1900-1 920 MHz 36.101, 5.5 Rel-8 no yes, no Band 332 Frequency band: 2010- 2025 MHz 36.101, 5.5 Rel-8 no yes, no Band 343 Frequency band: 1850- 1910 MHz 36.101, 5.5 Rel-8 no yes, no Band 354 Frequency band: 1930- 1990 MHz 36.101, 5.5 Rel-8 no yes, no Band 365 Frequency band: 1910- 1930 MHz 36.101, 5.5 Rel-8 no yes, no Band 376 Frequency band: 2570- 2620 MHz 36.101, 5.5 Rel-8 yes yes, no Band 387 Frequency band: 1880- 1920 MHz 36.101, 5.5 Rel-8 no yes, no Band 398 Frequency band: 2300- 2400 MHz 36.101, 5.5 Rel-8 yes yes, no Band 409 Frequency band: 2496-2690 MHz 36.101, 5.5 Rel-10 no yes, no Band 4110 Frequency band: 3400-3600 MHz 36.101, 5.5 Rel-10 no yes, no Band 4211 Frequency band: 3600-3800 MHz 36.101, 5.5 Rel-10 no yes, no Band 4312 Frequency band: 703-803 MHz 36.101, 5.5 Rel-11 no yes, no Band 44Table A.4.3.2-1 UE Category Reference Release Status Supported Allowed Comments1 Category 1 36.306, 4.1 Rel-8 no yes, no 2 Category 2 36.306, 4.1 Rel-8 no yes, no 3 Category 3 36.306, 4.1 Rel-8 no yes, no 4 Category 4 36.306, 4.1 Rel-8 yes yes, no 5 Category 5 36.306, 4.1 Rel-8 no yes, no 6 Category 6 36.306, 4.1 Rel-10 no yes, no Only in combination with DL Category 6, DL Category 9, DL Category 11 or DL Category 13 7 Category 7 36.306, 4.1 Rel-10 no yes, no 8 Category 8 36.306, 4.1 Rel-10 no yes, no 9 Category 9 36.306, 4.1 Rel-11 no yes, no Only in combination with DL Category 6, DL Category 9, DL Category 11 or DL Category 13 10 Category 10 36.306, 4.1 Rel-11 no yes, no 11 Category 11 36.306, 4.1 Rel-11 no yes, no 12 Category 12 36.306, 4.1 Rel-11 no yes, no Table A.4.3.2-2 UE Downlink Category Reference Release Status Supported Allowed Comments1 Category DL 0 36.306, 4.1A Rel-12 no yes, no 2 Category DL 6 36.306, 4.1A Rel-12 no yes, no 3 Category DL 7 36.306, 4.1A Rel-12 no yes, no 4 Category DL 9 36.306, 4.1A Rel-12 no yes, no 5 Category DL 10 36.306, 4.1A Rel-12 no yes, no 6 Category DL 11 36.306, 4.1A Rel-12 no yes, no 7 Category DL 12 36.306, 4.1A Rel-12 no yes, no 8 Category DL 13 36.306, 4.1A Rel-12 no yes, no Only in combination with Category UL 3 or Category UL 5 or Category UL 7 or Category UL 139 Category DL 14 36.306, 4.1A Rel‑12 no yes, no Only in combination with Category UL 810 Category DL 15 36.306, 4.1A Rel-12 no yes, no Only in combination with Category UL 3 or Category UL 5 or Category UL 7 or Category UL 1311 Category DL 16 36.306, 4.1A Rel‑12 no yes, no Only in combination with Category UL 3 or Category UL 5 or Category UL 7 or Category UL 13Table A.4.3.2-3 UE Uplink Category Reference Release Status Supported Allowed Comments1 Category UL 0 36.306, 4.1A Rel-12 no yes, no Only in combination with Category DL 02 Category UL 3 36.306, 4.1A Rel-12 no yes, no Only in combination with DL Category 133 Category UL 5 36.306, 4.1A Rel-12 no yes, no Only in combination with DL Category 6, DL Category 9, DL Category 11 or DL Category 13 4 Category UL 7 36.306, 4.1A Rel-12 no yes, no Only in combination with Category DL 135 Category UL 8 36.306, 4.1A Rel-12 no yes, no Only in combination with Category DL 146 Category UL 13 36.306, 4.1A Rel-12 no yes, no Only in combination with Category DL 7, Category DL 10, Category DL 12 or Category DL 13Table A.4.3.3-1 Downlink CA capabilities (for one or more of the supported CA configurations in Tables A.4.3.3.1-3, A.4.3.3.2-3, A.4.3.3.3-3, A.4.3.3.3-4 ) Reference Release Status Supported Allowed Comments1 DL CA with 2 carriers "36.101, 5.6A36.331, 6.3.6" no yes, no 2 DL CA with 3 carriers "36.101, 5.6A36.331, 6.3.6" no yes, no Table A.4.3.3-2 Uplink CA capabilities (for one or more of the supported CA configurations in Tables A.4.3.3.1-3, A.4.3.3.2-3, A.4.3.3.3-3, A.4.3.3.3-4) Reference Release Status Supported Allowed Comments1 UL CA with 2 carriers "36.101, 5.6A36.331, 6.3.6" no yes, no 2 UL CA with 3 carriers "36.101, 5.6A36.331, 6.3.6" no yes, no Not used in any valid CA configurations in TS 36.101 yetTable A.4.3.3.1-1 Downlink Intra-band contiguous CA Bandwidth Class capabilities (for one or more of the supported CA configurations in Table A.4.3.3.1-3) Reference Release Status Supported Allowed Comments1 DL Intra-band contiguous CA BW Class B "36.101, 5.6A36.331, 6.3.6" no yes, no 2 DL Intra-band contiguous CA BW Class C "36.101, 5.6A36.331, 6.3.6" no yes, no Table A.4.3.3.1-2 Uplink Intra-band contiguous CA Bandwidth Class capabilities (for one or more of the supported CA configurations in Table A.4.3.3.1-3) Reference Release Status Supported Allowed Comments1 UL Intra-band contiguous CA BW Class B "36.101, 5.6A36.331, 6.3.6" no yes, no Not used in any valid CA configurations in TS 36.101 yet2 UL Intra-band contiguous CA BW Class C "36.101, 5.6A36.331, 6.3.6" no yes, no Table A.4.3.3.1-3 Supported CA configurations for Intra-band contiguous CA Reference Release Status Supported Allowed Comments1.1 "CA_1C(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-10 no yes, no 1.2 "CA_1C(Supported Bandwidth Combination Set(s) (Note 3))" Rel-10 no yes, no 2.1 "CA_2C(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 2.2 "CA_2C(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 3.1 "CA_3C(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 3.2 "CA_3C(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 4.1 "CA_5B(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-13 no yes, no 4.2 "CA_5B(Supported Bandwidth Combination Set(s) (Note 3))" Rel-13 no yes, no 5.1 "CA_7C(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-11 no yes, no 5.2 "CA_7C(Supported Bandwidth Combination Set(s) (Note 3))" Rel-11 no yes, no 6.1 "CA_12B(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 6.2 "CA_12B(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 7.1 "CA_23B(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 7.2 "CA_23B(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 8.1 "CA_27B(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 8.2 "CA_27B(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 9.1 "CA_38C(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-11 no yes, no 9.2 "CA_38C(Supported Bandwidth Combination Set(s) (Note 3))" Rel-11 no yes, no 10.1 "CA_39C(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 10.2 "CA_39C(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 11.1 "CA_40C(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-10 no yes, no 11.2 "CA_40C(Supported Bandwidth Combination Set(s) (Note 3))" Rel-10 no yes, no 12.1 "CA_40D(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 12.2 "CA_40D(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 13.1 "CA_41C(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-11 no yes, no 13.2 "CA_41C(Supported Bandwidth Combination Set(s) (Note 3))" Rel-11 no yes, no 14.1 "CA_41D(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 14.2 "CA_41D(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 15.1 "CA_42C(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 15.2 "CA_42C(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no Note "Note 1: Notation used for intra-band contiguous CA Bands is according to TS 36.101 [2] Table 5.6A.1-1, e.g. ‘CA_1C’ indicates CA operation on E-UTRA band 1 with DL CA Bandwidth Class C.Note 2: The UL CA capabilities as per Table A.4.3.3-2can be supported on a single or multiple CA Band(s). The UE supplier shall indicate all supported UL CA Bandwidth Class(es), in uplink of the supported CA Band(s), as per TS 36.101 [2] Table 5.6A.1-1. For this release of specification valid choices are ’N’, ‘XB’ and ‘XC’, where X is the band. For example, for CA_1C, N would mean only DL CA, ‘1C’ would mean both DL and UL CA.Note 3: The UE supplier shall indicate the supported Bandwidth Combination Set(s) as per TS 36.101 [2] Table 5.6A.1-1.Note 4: Reference to all items is 36.101, 5.6A and 36.331, 6.3.6." Table A.4.3.3.2-1 Downlink Intra-band non-contiguous CA Bandwidth Class capabilities (for one or more of the supported CA configurations in Table A.4.3.3.2-3) Reference Release Status Supported Allowed Comments1 DL Intra-band non-contiguous CA BW Class Combination A-A "36.101, 5.6A36.331, 6.3.6" no yes, no Table A.4.3.3.2-2 Uplink Intra-band non-contiguous CA Bandwidth Class capabilities (for one or more of the supported CA configurations in Table A.4.3.3.2-3) Reference Release Status Supported Allowed Comments1 UL Intra-band non-contiguous CA BW Combination class A-A "36.101, 5.6A36.331, 6.3.6" no yes, no Table A.4.3.3.2-3 Supported CA configurations for Intra-band non-contiguous CA Reference Release Status Supported Allowed Comments1.1 "CA_2A-2A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 1.2 "CA_2A-2A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 2.1 "CA_3A-3A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 2.2 "CA_3A-3A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 3.1 "CA_4A-4A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 3.2 "CA_4A-4A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 4.1 "CA_5A-5A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-13 no yes, no 4.2 "CA_5A-5A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-13 no yes, no 5.1 "CA_7A-7A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 5.2 "CA_7A-7A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 6.1 "CA_23A-23A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 6.2 "CA_23A-23A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 7.1 "CA_25A-25A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-11 no yes, no 7.8 "CA_25A-25A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-11 no yes, no 8.1 "CA_41A-41A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-11 no yes, no 8.2 "CA_41A-41A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-11 no yes, no 9.1 "CA_41A-41C(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 9.2 "CA_41A-41C(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 10.1 "CA_41C-41A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 10.2 "CA_41C-41A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 11.1 "CA_42A-42A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 11.2 "CA_42A-42A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no Note "Note 1: Notation used for intra-band contiguous CA Bands is according to TS 36.101 [2] Table 5.6A.1-3, e.g. ‘CA_2A-2A’ indicates CA intra-band non-contiguous operation on E-UTRA band 2 with DL CA Bandwidth Class A-A.Note 2: The UL CA capabilities as per Table A.4.3.3-2 can be supported on a single or multiple CA Band(s). The UE supplier shall indicate all supported UL CA Bandwidth Class(es), in uplink of the supported CA Band(s), as per TS 36.101 [2] Table 5.6A.1-3. For this release of specification valid choices are ‘N’, ‘XA-XA’ and ‘XC’, where X is the band. For example, for CA_4A-4A, ‘N’ would mean only DL CA, ‘4A-4A’ would mean both DL and UL CA.Note 3: The UE supplier shall indicate the supported Bandwidth Combination Set(s) as per TS 36.101 [2] Table 5.6A.1-3.Note 4: Reference to all items is 36.101, 5.6A and 36.331, 6.3.6." Table A.4.3.3.3-1 Downlink Inter-band CA Bandwidth Class Combination capabilities (for one or more of the supported CA configurations in Table A.4.3.3.3-3) Reference Release Status Supported Allowed Comments1 DL Inter-band CA BW Class Combination A-A "36.101, 5.6A36.331, 6.3.6" no yes, no Table A.4.3.3.3-2 Uplink Inter-band CA Bandwidth Class Combination capabilities (for one or more of the supported CA configurations in Table A.4.3.3.3-3) Reference Release Status Supported Allowed Comments1 UL Inter-band CA BW Combination class A-A "36.101, 5.6A36.331, 6.3.6" no yes, no Not used in any valid CA configurations in TS 36.101 yet2 UL (Pcell) supported in each band of Inter-band CA combination under test "36.101, 5.6A36.331, 6.3.6" no yes, no Table A.4.3.3.3-3 Supported CA configurations for Inter-band CA Reference Release Status Supported Allowed Comments1.1 "CA_1A-3A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 1.2 "CA_1A-3A(Supported UL Bands (Note 5))" Rel-12 no yes, no 1.3 "CA_1A-3A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 2.1 "CA_1A-5A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-10 no yes, no 2.2 "CA_1A-5A(Supported UL Bands (Note 5))" Rel-10 no yes, no 2.3 "CA_1A-5A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-10 no yes, no 3.1 "CA_1A-7A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 3.2 "CA_1A-7A(Supported UL Bands (Note 5))" Rel-12 no yes, no 3.3 "CA_1A-7A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 4.1 "CA_1A-8A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 4.2 "CA_1A-8A(Supported UL Bands (Note 5))" Rel-12 no yes, no 4.3 "CA_1A-8A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 5.1 "CA_1A-11A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 5.2 "CA_1A-11A(Supported UL Bands (Note 5))" Rel-12 no yes, no 5.3 "CA_1A-11A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 6.1 "CA_1A-18A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-11 no yes, no 6.2 "CA_1A-18A(Supported UL Bands (Note 5))" Rel-11 no yes, no 6.3 "CA_1A-18A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-11 no yes, no 7.1 "CA_1A-19A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-11 no yes, no 7.2 "CA_1A-19A(Supported UL Bands (Note 5))" Rel-11 no yes, no 7.3 "CA_1A-19A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-11 no yes, no 8.1 "CA_1A-20A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 8.2 "CA_1A-20A(Supported UL Bands (Note 5))" Rel-12 no yes, no 8.3 "CA_1A-20A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 9.1 "CA_1A-21A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-11 no yes, no 9.2 "CA_1A-21A(Supported UL Bands (Note 5))" Rel-11 no yes, no 9.3 "CA_1A-21A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-11 no yes, no 10.1 "CA_1A-26A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 10.2 "CA_1A-26A(Supported UL Bands (Note 5))" Rel-12 no yes, no 10.3 "CA_1A-26A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 11.1 "CA_1A-28A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 11.2 "CA_1A-28A(Supported UL Bands (Note 5))" Rel-12 no yes, no 11.3 "CA_1A-28A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 12.1 "CA_1A-41A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 12.2 "CA_1A-41A(Supported UL Bands (Note 5))" Rel-12 no yes, no 12.3 "CA_1A-41A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 13.1 "CA_1A-41C(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 13.2 "CA_1A-41C(Supported UL Bands (Note 5))" Rel-12 no yes, no 13.3 "CA_1A-41C(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 14.1 "CA_1A-42A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 14.2 "CA_1A-42A(Supported UL Bands (Note 5))" Rel-12 no yes, no 14.3 "CA_1A-42A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 15.1 "CA_1A-42C(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 15.2 "CA_1A-42C(Supported UL Bands (Note 5))" Rel-12 no yes, no 15.3 "CA_1A-42C(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 16.1 "CA_2A-2A-5A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 16.2 "CA_2A-2A-5A(Supported UL Bands (Note 5))" Rel-12 no yes, no 16.3 "CA_2A-2A-5A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 17.1 "CA_2A-2A-13A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 17.2 "CA_2A-2A-13A(Supported UL Bands (Note 5))" Rel-12 no yes, no 17.3 "CA_2A-2A-13A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 18.1 "CA_2A-4A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 18.2 "CA_2A-4A(Supported UL Bands (Note 5))" Rel-12 no yes, no 18.3 "CA_2A-4A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 19.1 "CA_2A-4A-4A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 19.2 "CA_2A-4A-4A(Supported UL Bands (Note 5))" Rel-12 no yes, no 19.3 "CA_2A-4A-4A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 20.1 "CA_2A-5A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 20.2 "CA_2A-5A(Supported UL Bands (Note 5))" Rel-12 no yes, no 20.3 "CA_2A-5A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 21.1 "CA_2A-12A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 21.2 "CA_2A-12A(Supported UL Bands (Note 5))" Rel-12 no yes, no 21.3 "CA_2A-12A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 22.1 "CA_2A-12B(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 22.2 "CA_2A-12B(Supported UL Bands (Note 5))" Rel-12 no yes, no 22.3 "CA_2A-12B(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 23.1 "CA_2A-13A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 23.2 "CA_2A-13A(Supported UL Bands (Note 5))" Rel-12 no yes, no 23.3 "CA_2A-13A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 24.1 "CA_2A-17A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-11 no yes, no 24.2 "CA_2A-17A(Supported UL Bands (Note 5))" Rel-11 no yes, no 24.3 "CA_2A-17A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-11 no yes, no 25.1 "CA_2A-29A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-11 no yes, no 25.2 "CA_2A-29A(Supported UL Bands (Note 5))" Rel-11 no yes, no 25.3 "CA_2A-29A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-11 no yes, no 26.1 "CA_2C-29A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 26.2 "CA_2C-29A(Supported UL Bands (Note 5))" Rel-12 no yes, no 26.3 "CA_2C-29A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 27.1 "CA_2A-30A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 27.2 "CA_2A-30A(Supported UL Bands (Note 5))" Rel-12 no yes, no 27.3 "CA_2A-30A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 28.1 "CA_3A-5A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-11 no yes, no 28.2 "CA_3A-5A(Supported UL Bands (Note 5))" Rel-11 no yes, no 28.3 "CA_3A-5A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-11 no yes, no 29.1 "CA_3C-5A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-13 no yes, no 29.2 "CA_3C-5A(Supported UL Bands (Note 5))" Rel-13 no yes, no 29.3 "CA_3C-5A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-13 no yes, no 30.1 "CA_3A-7A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-11 no yes, no 30.2 "CA_3A-7A(Supported UL Bands (Note 5))" Rel-11 no yes, no 30.3 "CA_3A-7A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-11 no yes, no 31.1 "CA_3A-7C(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 31.2 "CA_3A-7C(Supported UL Bands (Note 5))" Rel-12 no yes, no 31.3 "CA_3A-7C(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 32.1 "CA_3C-7A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 32.2 "CA_3C-7A(Supported UL Bands (Note 5))" Rel-12 no yes, no 32.3 "CA_3C-7A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 33.1 "CA_3A-8A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-11 no yes, no 33.2 "CA_3A-8A(Supported UL Bands (Note 5))" Rel-11 no yes, no 33.3 "CA_3A-8A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-11 no yes, no 34.1 "CA_3A-19A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 34.2 "CA_3A-19A(Supported UL Bands (Note 5))" Rel-12 no yes, no 34.3 "CA_3A-19A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 35.1 "CA_3A-20A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-11 no yes, no 35.2 "CA_3A-20A(Supported UL Bands (Note 5))" Rel-11 no yes, no 35.3 "CA_3A-20A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-11 no yes, no 36.1 "CA_3A-26A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 36.2 "CA_3A-26A(Supported UL Bands (Note 5))" Rel-12 no yes, no 36.3 "CA_3A-26A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 37.1 "CA_3A-27A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 37.2 "CA_3A-27A(Supported UL Bands (Note 5))" Rel-12 no yes, no 37.3 "CA_3A-27A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 38.1 "CA_3A-28A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 38.2 "CA_3A-28A(Supported UL Bands (Note 5))" Rel-12 no yes, no 38.3 "CA_3A-28A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 39.1 "CA_3A-42A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 39.2 "CA_3A-42A(Supported UL Bands (Note 5))" Rel-12 no yes, no 39.3 "CA_3A-42A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 40.1 "CA_3A-42C(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 40.2 "CA_3A-42C(Supported UL Bands (Note 5))" Rel-12 no yes, no 40.3 "CA_3A-42C(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 41.1 "CA_4A-5A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-11 no yes, no 41.2 "CA_4A-5A(Supported UL Bands (Note 5))" Rel-11 no yes, no 41.3 "CA_4A-5A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-11 no yes, no 42.1 "CA_4A-4A-5A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 42.2 "CA_4A-4A-5A(Supported UL Bands (Note 5))" Rel-12 no yes, no 42.3 "CA_4A-4A-5A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 43.1 "CA_4A-7A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-11 no yes, no 43.2 "CA_4A-7A(Supported UL Bands (Note 5))" Rel-11 no yes, no 43.3 "CA_4A-7A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-11 no yes, no 44.1 "CA_4A-4A-7A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 44.2 "CA_4A-4A-7A(Supported UL Bands (Note 5))" Rel-12 no yes, no 44.3 "CA_4A-4A-7A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 45.1 "CA_4A-12A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-11 no yes, no 45.2 "CA_4A-12A(Supported UL Bands (Note 5))" Rel-11 no yes, no 45.3 "CA_4A-12A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-11 no yes, no 46.1 "CA_4A-4A-12A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 46.2 "CA_4A-4A-12A(Supported UL Bands (Note 5))" Rel-12 no yes, no 46.3 "CA_4A-4A-12A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 47.1 "CA_4A-12B(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 47.2 "CA_4A-12B(Supported UL Bands (Note 5))" Rel-12 no yes, no 47.3 "CA_4A-12B(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 48.1 "CA_4A-13A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-11 no yes, no 48.2 "CA_4A-13A(Supported UL Bands (Note 5))" Rel-11 no yes, no 48.3 "CA_4A-13A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-11 no yes, no 49.1 "CA_4A-4A-13A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 49.2 "CA_4A-4A-13A(Supported UL Bands (Note 5))" Rel-12 no yes, no 49.3 "CA_4A-4A-13A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 50.1 "CA_4A-17A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-11 no yes, no 50.2 "CA_4A-17A(Supported UL Bands (Note 5))" Rel-11 no yes, no 50.3 "CA_4A-17A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-11 no yes, no 51.1 "CA_4A-27A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 51.2 "CA_4A-27A(Supported UL Bands (Note 5))" Rel-12 no yes, no 51.3 "CA_4A-27A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 52.1 "CA_4A-29A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-11 no yes, no 52.2 "CA_4A-29A(Supported UL Bands (Note 5))" Rel-11 no yes, no 52.3 "CA_4A-29A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-11 no yes, no 53.1 "CA_4A-30A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 53.2 "CA_4A-30A(Supported UL Bands (Note 5))" Rel-12 no yes, no 53.3 "CA_4A-30A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 54.1 "CA_5A-7A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 54.2 "CA_5A-7A(Supported UL Bands (Note 5))" Rel-12 no yes, no 54.3 "CA_5A-7A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 55.1 "CA_5A-12A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-11 no yes, no 55.2 "CA_5A-12A(Supported UL Bands (Note 5))" Rel-11 no yes, no 55.3 "CA_5A-12A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-11 no yes, no 56.1 "CA_5A-13A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 56.2 "CA_5A-13A(Supported UL Bands (Note 5))" Rel-12 no yes, no 56.3 "CA_5A-13A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 57.1 "CA_5A-17A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-11 no yes, no 57.2 "CA_5A-17A(Supported UL Bands (Note 5))" Rel-11 no yes, no 57.3 "CA_5A-17A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-11 no yes, no 58.1 "CA_5A-25A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 58.2 "CA_5A-25A(Supported UL Bands (Note 5))" Rel-12 no yes, no 58.3 "CA_5A-25A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 59.1 "CA_5A-30A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 59.2 "CA_5A-30A(Supported UL Bands (Note 5))" Rel-12 no yes, no 59.3 "CA_5A-30A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 60.1 "CA_7A-8A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 60.2 "CA_7A-8A(Supported UL Bands (Note 5))" Rel-12 no yes, no 60.3 "CA_7A-8A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 61.1 "CA_7A-12A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 61.2 "CA_7A-12A(Supported UL Bands (Note 5))" Rel-12 no yes, no 61.3 "CA_7A-12A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 62.1 "CA_7A-20A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-11 no yes, no 62.2 "CA_7A-20A(Supported UL Bands (Note 5))" Rel-11 no yes, no 62.3 "CA_7A-20A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-11 no yes, no 63.1 "CA_7A-28A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 63.2 "CA_7A-28A(Supported UL Bands (Note 5))" Rel-12 no yes, no 63.3 "CA_7A-28A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 64.1 "CA_8A-11A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 64.2 "CA_8A-11A(Supported UL Bands (Note 5))" Rel-12 no yes, no 64.3 "CA_8A-11A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 65.1 "CA_8A-20A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-11 no yes, no 65.2 "CA_8A-20A(Supported UL Bands (Note 5))" Rel-11 no yes, no 65.3 "CA_8A-20A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-11 no yes, no 66.1 "CA_11A-18A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-11 no yes, no 66.2 "CA_11A-18A(Supported UL Bands (Note 5))" Rel-11 no yes, no 66.3 "CA_11A-18A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-11 no yes, no 67.1 "CA_12A-25A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 67.2 "CA_12A-25A(Supported UL Bands (Note 5))" Rel-12 no yes, no 67.3 "CA_12A-25A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 68.1 "CA_12A-30A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 68.2 "CA_12A-30A(Supported UL Bands (Note 5))" Rel-12 no yes, no 68.3 "CA_12A-30A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 69.1 "CA_18A-28A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 69.2 "CA_18A-28A(Supported UL Bands (Note 5))" Rel-12 no yes, no 69.3 "CA_18A-28A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 70.1 "CA_19A-21A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 70.2 "CA_19A-21A(Supported UL Bands (Note 5))" Rel-12 no yes, no 70.3 "CA_19A-21A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 71.1 "CA_19A-42A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 71.2 "CA_19A-42A(Supported UL Bands (Note 5))" Rel-12 no yes, no 71.3 "CA_19A-42A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 72.1 "CA_19A-42C(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 72.2 "CA_19A-42C(Supported UL Bands (Note 5))" Rel-12 no yes, no 72.3 "CA_19A-42C(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 73.1 "CA_20A-32A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 73.2 "CA_20A-32A(Supported UL Bands (Note 5))" Rel-12 no yes, no 73.3 "CA_20A-32A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 74.1 "CA_20A-67A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-13 no yes, no 74.2 "CA_20A-67A(Supported UL Bands (Note 5))" Rel-13 no yes, no 74.3 "CA_20A-67A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-13 no yes, no 75.1 "CA_23A-29A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 75.2 "CA_23A-29A(Supported UL Bands (Note 5))" Rel-12 no yes, no 75.3 "CA_23A-29A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 76.1 "CA_26A-41A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 76.2 "CA_26A-41A(Supported UL Bands (Note 5))" Rel-12 no yes, no 76.3 "CA_26A-41A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 77.1 "CA_26A-41C(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 77.2 "CA_26A-41C(Supported UL Bands (Note 5))" Rel-12 no yes, no 77.3 "CA_26A-41C(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 78.1 "CA_29A-30A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 78.2 "CA_29A-30A(Supported UL Bands (Note 5))" Rel-12 no yes, no 78.3 "CA_29A-30A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 79.1 "CA_39A-41A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 79.2 "CA_39A-41A(Supported UL Bands (Note 5))" Rel-12 no yes, no 79.3 "CA_39A-41A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 80.1 "CA_39A-41C(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 80.2 "CA_39A-41C(Supported UL Bands (Note 5))" Rel-12 no yes, no 80.3 "CA_39A-41C(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 81.1 "CA_41A-42A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 81.2 "CA_41A-42A(Supported UL Bands (Note 5))" Rel-12 no yes, no 81.3 "CA_41A-42A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no Note "Note 1: Notation used for intra-band contiguous CA Bands is according to TS 36.101 [2] Table 5.6A.1-2, e.g. ‘CA_1A-3A’ indicates interband CA operation on E-UTRA band 1 with DL CA Bandwidth Class A and on E-UTRA band 3 with DL CA Bandwidth Class A.Note 2: The UL CA capabilities as per Table A.4.3.3-2 can be supported on a single or multiple CA Band(s). The UE supplier shall indicate all supported UL CA Bandwidth Class(es), in uplink of the supported CA Band(s), as per TS 36.101 [2] Table 5.6A.1-2. For this release of specification valid choices are ‘N’, ‘XA-XA’ and ‘XC’, where X is the band. For example, for full UL CA support in CA_18A-28A, UE shall indicate 18A-28A. For no UL CA ‘N’.Note 3: The UE supplier shall indicate the supported Bandwidth Combination Set(s) as per TS 36.101 [2] Table 5.6A.1-2.Note 4: Reference to all items is 36.101, 5.6A and 36.331, 6.3.6.Note 5: List all the CA Combination bands where UL is supported." Table A.4.3.3.3-4 Supported CA configurations for Inter-band CA (three bands) Reference Release Status Supported Allowed Comments1.1 "CA_1A-3A-5A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 1.2 "CA_1A-3A-5A(Supported UL Bands (Note 5))" Rel-12 no yes, no 1.3 "CA_1A-3A-5A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 2.1 "CA_1A-3A-8A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 2.2 "CA_1A-3A-8A(Supported UL Bands (Note 5))" Rel-12 no yes, no 2.3 "CA_1A-3A-8A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 3.1 "CA_1A-3A-19A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 3.2 "CA_1A-3A-19A(Supported UL Bands (Note 5))" Rel-12 no yes, no 3.3 "CA_1A-3A-19A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 4.1 "CA_1A-3A-20A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 4.2 "CA_1A-3A-20A(Supported UL Bands (Note 5))" Rel-12 no yes, no 4.3 "CA_1A-3A-20A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 5.1 "CA_1A-3A-26A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 5.2 "CA_1A-3A-26A(Supported UL Bands (Note 5))" Rel-12 no yes, no 5.3 "CA_1A-3A-26A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 6.1 "CA_1A-5A-7A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 6.2 "CA_1A-5A-7A(Supported UL Bands (Note 5))" Rel-12 no yes, no 6.3 "CA_1A-5A-7A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 7.1 "CA_1A-7A-20A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 7.2 "CA_1A-7A-20A(Supported UL Bands (Note 5))" Rel-12 no yes, no 7.3 "CA_1A-7A-20A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 8.1 "CA_1A-18A-28A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 8.2 "CA_1A-18A-28A(Supported UL Bands (Note 5))" Rel-12 no yes, no 8.3 "CA_1A-18A-28A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 9.1 "CA_1A-19A-21A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 9.2 "CA_1A-19A-21A(Supported UL Bands (Note 5))" Rel-12 no yes, no 9.3 "CA_1A-19A-21A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 10.1 "CA_2A-4A-5A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 10.2 "CA_2A-4A-5A(Supported UL Bands (Note 5))" Rel-12 no yes, no 10.3 "CA_2A-4A-5A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 11.1 "CA_2A-4A-12A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 11.2 "CA_2A-4A-12A(Supported UL Bands (Note 5))" Rel-12 no yes, no 11.3 "CA_2A-4A-12A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 12.1 "CA_2A-4A-13A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 12.2 "CA_2A-4A-13A(Supported UL Bands (Note 5))" Rel-12 no yes, no 12.3 "CA_2A-4A-13A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 13.1 "CA_2A-4A-29A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 13.2 "CA_2A-4A-29A(Supported UL Bands (Note 5))" Rel-12 no yes, no 13.3 "CA_2A-4A-29A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 14.1 "CA_2A-5A-12A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 14.2 "CA_2A-5A-12A(Supported UL Bands (Note 5))" Rel-12 no yes, no 14.3 "CA_2A-5A-12A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 15.1 "CA_2A-5A-13A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 15.2 "CA_2A-5A-13A(Supported UL Bands (Note 5))" Rel-12 no yes, no 15.3 "CA_2A-5A-13A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 16.1 "CA_2A-5A-30A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 16.2 "CA_2A-5A-30A(Supported UL Bands (Note 5))" Rel-12 no yes, no 16.3 "CA_2A-5A-30A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 17.1 "CA_2A-12A-30A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 17.2 "CA_2A-12A-30A(Supported UL Bands (Note 5))" Rel-12 no yes, no 17.3 "CA_2A-12A-30A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 18.1 "CA_2A-29A-30A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 18.2 "CA_2A-29A-30A(Supported UL Bands (Note 5))" Rel-12 no yes, no 18.3 "CA_2A-29A-30A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 19.1 "CA_3A-7A-20A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 19.2 "CA_3A-7A-20A(Supported UL Bands (Note 5))" Rel-12 no yes, no 19.3 "CA_3A-7A-20A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 20.1 "CA_4A-5A-12A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 20.2 "CA_4A-5A-12A(Supported UL Bands (Note 5))" Rel-12 no yes, no 20.3 "CA_4A-5A-12A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 21.1 "CA_4A-5A-13A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 21.2 "CA_4A-5A-13A(Supported UL Bands (Note 5))" Rel-12 no yes, no 21.3 "CA_4A-5A-13A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 22.1 "CA_4A-5A-30A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 22.2 "CA_4A-5A-30A(Supported UL Bands (Note 5))" Rel-12 no yes, no 22.3 "CA_4A-5A-30A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 23.1 "CA_4A-7A-12A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 23.2 "CA_4A-7A-12A(Supported UL Bands (Note 5))" Rel-12 no yes, no 23.3 "CA_4A-7A-12A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 24.1 "CA_4A-12A-30A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 24.2 "CA_4A-12A-30A(Supported UL Bands (Note 5))" Rel-12 no yes, no 24.3 "CA_4A-12A-30A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 25.1 "CA_4A-29A-30A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 25.2 "CA_4A-29A-30A(Supported UL Bands (Note 5))" Rel-12 no yes, no 25.3 "CA_4A-29A-30A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no 26.1 "CA_7A-8A-20A(Supported CA Bandwidth Class(es) in UL (Note 2))" Rel-12 no yes, no 26.2 "CA_7A-8A-20A(Supported UL Bands (Note 5))" Rel-12 no yes, no 26.3 "CA_7A-8A-20A(Supported Bandwidth Combination Set(s) (Note 3))" Rel-12 no yes, no Note "Note 1: Notation used for intra-band contiguous CA Bands is according to TS 36.101 [2] Table 5.6A.1-2a, e.g. ‘CA_1A-3A-19A’ indicates CA operation on E-UTRA bands 1, 3 and 19, each with CA Bandwidth class A.Note 2: The UL CA capabilities as per Table A.4.3.3-2 can be supported on a single or multiple CA Band(s). The UE supplier shall indicate all supported UL CA Bandwidth Class(es), in uplink of the supported CA Band(s), as per TS 36.101 [2] Table 5.6A.1-2a. The UE shall also indicate in which bands is UL supported. For this release of specification valid choices are ‘N’, ‘XA-YA’ etc, where X,Y,Z are the bands. For example, for UL support in B1+B3, and B3+B19, for CA_1A-3A-19A, UE shall indicate ‘1A-3A’,’3A-19A’,Note 3: The UE supplier shall indicate the supported Bandwidth Combination Set(s) as per TS 36.101 [2] Table 5.6A.1-2a.Note 4: Reference to all items is 36.101, 5.6A and 36.331, 6.3.6.Note 5: List all the CA Combination bands where UL is supported." Table A.4.3.4-1 ProSe Physical Layer Implementation Capabilities Reference Release Status Supported Allowed Comments1 The bands on which the UE supports sidelink communication 36.306, 4.3.21.1 Rel-12 no yes, no commSupportedBands-r122 For a particular band combination, the bands on which the UE supports simultaneous reception of EUTRA and sidelink communication 36.306, 4.3.5.12 Rel-12 no yes, no commSupportedBandsPerBC-r123 The bands on which the UE supports sidelink discovery 36.306, 4.3.21.3 Rel-12 no yes, no discSupportedBands-r124 The number of processes supported by the UE for reception of sidelink discovery 36.306, 4.3.21.7 Rel-12 no yes, no discSupportedProc-r12Table A.4.4-1 Additional information Reference Release Status Supported Allowed Comments1 Support of USIM removal without power down Rel-8 no yes, no pc_USIM_Removal2 Support of Allowed CSG list 36.331 Annex B.2 Rel-8 no yes, no "pc_Allowed_CSG_listFor Rel-8: CSG autonomous search is optional.For Rel-9 or later releases: CSG autonomous search is mandatory for UEs supporting CSG full functionality."3 Support of Short Message Service (SMS) MT over SGs 23.272, 8.2.4, 8.2.5 Rel-8 yes yes, no pc_SMS_SGs_MT4 Support of Short Message Service (SMS) MO over SGs 23.272, 8.2.2, 8.2.3 Rel-8 yes yes, no pc_SMS_SGs_MO5 Support of ISR 23.401, 4.3.5.6 Rel-8 yes yes, no pc_ISR6 Support of Mobility management based on Dual-Stack Mobile IPv6 24.303 Rel-8 yes yes, no pc_DSMIPv67 Support for being configured to discover the Home Agent address via DNS 24.303 Rel-8 no yes, no pc_HAAddress_via_DNS8 Support of inter-RAT PS handover to E-UTRA (FDD) from UTRA 25.306, 4.7 Rel-8 yes yes, no pc_HO_from_UTRA_to_eFDD9 Support of EMM information message 24.301, 5.4.5.3 Rel-8 yes yes, no pc_EMM_Information10 Support for being configured to discover the Home Agent address via DHCPv6 24.303 Rel-8 no yes, no pc_HAAddress_via_DHCPv611 Void 12 Upon reception of 'Full name for network' information the UE stores/updates the network full name 24.301, 8.2.13 Rel-8 yes yes, no pc_FullNameNetwork13 Upon reception of 'Short name for network' information the UE stores/updates the network short name 24.301, 8.2.13 Rel-8 no yes, no pc_ShortNameNetwork14 Upon reception of 'Local time zone' information the UE stores/updates the local time zone 24.301, 8.2.13 Rel-8 no yes, no pc_LocalTimeZone15 Upon reception of 'Universal time and local time zone' information the UE stores/updates the universal time and local time zone 24.301, 8.2.13 Rel-8 no yes, no pc_UniversalAndLocalTimeZone16 Void 17 Support of switch on/off Rel-8 yes yes, no pc_SwitchOnOff18 Support of ESM UE requested bearer resource allocation procedure 24.301, 6.5.3 Rel-8 yes yes, no pc_ESM_MO_Bearer_Allocation19 Support of ESM UE requested bearer resource modification procedure 24.301, 6.5.4 Rel-8 yes yes, no pc_ESM_MO_Bearer_Modification20 Support of ETWS message 23.401, 5.12.2 Rel-8 no yes, no pc_ETWS_message21 Supports E-UTRAN Neighbour Cell measurements and MS autonomous cell reselection to E-UTRAN 24.008, 10.5.5.12a Rel-8 yes yes, no pc_GERAN_2_E_UTRAN_meas22 Support for being configured to request the IPv6 address of the Home Agent during Attach procedure 24.303 Rel-8 no yes, no pc_RequestIPv6HAAddress_DuringAttach23 Support for being configured to request the IPv4 address of the Home Agent during Attach procedure 24.303 Rel-8 no yes, no pc_RequestIPv4HAAddress_DuringAttach24 Void 25 Support of IMS 24.229 Rel-8 no yes, no pc_IMS26 Supports of disabling the EPS services 24.301, 3.1, 5.5.2.1 Rel-8 yes yes, no pc_EPS_Services_Disable27 Support of automatic re-activation of the EPS bearer(s) during Network Initiated Detach with detach type set to “re-attach required” "24.301, 5.5.2.3.2" Rel-8 yes yes, no pc_Automatic_Re_Attach28 Support of Compressed mode 25.306 Rel-8 yes yes, no pc_UTRA_CompressedModeRequired29 Support of GERAN to E-UTRAN PS Handover 24.008, 10.5.5.12a Rel-8 no yes, no pc_GERAN_2_E_UTRAN_PSHO30 Support for multiple PDN connections 23.401, 5.10 Rel-8 yes yes, no pc_Multiple_PDN31 Support of use of the UTRA system information provided by RRCConnectionRelease upon redirection 36.306 Rel-9 yes yes, no pc_eRedirectionUTRA32 Support for SRVCC from E-UTRAN to GERAN/UTRAN 24.301, 8.2.4 Rel-8 yes yes, no pc_SRVCC_GERAN_UTRAN33 Support for VoLTE in GSMA PRD IR.92: “IMS Profile for Voice and SMS” "24.17324.229, 26.114, 5.2.1, GSMA PRD IR.92" Rel-8 no yes, no "pc_VoLTEMultimedia telephony service participantin itiating a speech session.UE supports sending DTMF events over RTP."34 Support of detach for non-EPS services 24.301, 5.5.2.1 Rel-8 no yes, no pc_IMSI_Detach35 Support for establishing the emergency call using the CS domain in UTRA after ATTACH REJECT to emergency bearer service 24.301, 5.5.1.2.5A Rel-9 yes yes, no pc_CS_Em_Call_in_UTRA36 Support for establishing the emergency call using the CS domain in GERAN after ATTACH REJECT to emergency bearer service 24.301, 5.5.1.2.5A Rel-9 yes yes, no pc_CS_Em_Call_in_GERAN37 Support for establishing the emergency call using the CS domain in 1xRTT after ATTACH REJECT to emergency bearer service 24.301, 5.5.1.2.5A Rel-9 no yes, no pc_CS_Em_Call_in_1xRTT38 Support for EDTM 44.060 8.9.1.2 Rel-8 no yes, no pc_EDTM39 Supports CCN towards E-UTRAN, E-UTRAN Neighbour Cell measurement reporting and Network controlled cell reselection to E-UTRAN 24.008, 10.5.5.12a Rel-8 no yes, no pc_GERAN_2_E_UTRAN_measreporting_CCN40 Support for ROHC profile0x0001 36.306, 4.3.1.1 Rel-8 yes yes, no "pc_ROHC_profile0x0001'IMS capable UEs supporting voice' shall set this PICS to true."41 Support for ROHC profile0x0002 36.306, 4.3.1.1 Rel-8 yes yes, no "pc_ROHC_profile0x0002'IMS capable UEs supporting voice' shall set this PICS to true."42 Support for ROHC profile0x0003 36.306, 4.3.1.1 Rel-8 no yes, no pc_ROHC_profile0x000343 Support for ROHC profile0x0004 36.306, 4.3.1.1 Rel-8 yes yes, no pc_ROHC_profile0x000444 Support for ROHC profile0x0006 36.306, 4.3.1.1 Rel-8 no yes, no pc_ROHC_profile0x000645 Support for ROHC profile0x0101 36.306, 4.3.1.1 Rel-8 no yes, no pc_ROHC_profile0x010146 Support for ROHC profile0x0102 36.306, 4.3.1.1 Rel-8 no yes, no pc_ROHC_profile0x010247 Support for ROHC profile0x0103 36.306, 4.3.1.1 Rel-8 no yes, no pc_ROHC_profile0x010348 Support for ROHC profile0x0104 36.306, 4.3.1.1 Rel-8 no yes, no pc_ROHC_profile0x010449 Support of manual CSG selection 36.331, Annex B2 Rel-8 no yes, no "pc_manual_CSG_selectionFor Rel-8: manual CSG selection is optional.For Rel-9 or later releases: manual CSG selection is mandatory for UEs supporting CSG full functionality."50 Support of semi-persistence scheduling 36.331, Annex B1 Rel-8 yes yes, no "pc_semi_persistence_schedulingFor Rel-8: semi-persistence scheduling is mandatory if pc_FeatrGrp_3 is set to true.For Rel-9 or later releases: semi-persistence scheduling is mandatory if pc_FeatrGrp_29 is set to true."51 Support of TTI bundling 36.331, Annex B1 Rel-8 yes yes, no "pc_TTI_bundlingFor Rel-8: TTI bundling is mandatory if pc_FeatrGrp_3 is set to true.For Rel-9 TDD: TTI bundling is mandatory if pc_FeatrGrp_28 is set to true.For Rel-9 FDD: pc_FeatrGrp_28 must be set to true.For Rel 10 or later releases: pc_FeatrGrp_28 must be set to true."52 Support for inter-RAT PS handover from E-UTRAN to GERAN "36.306,4.3.7.11" Rel-8 yes yes, no pc_E_UTRAN_2_GERAN_PSHO53 Support of inter-RAT PS handover to E-UTRA (TDD) from UTRA 25.306, 4.7 Rel-8 yes yes, no pc_HO_from_UTRA_to_eTDD54 Support for UE requested modification of network allocated TFTs 24.301, 6.5.4 Rel-8 no yes, no pc_ESM_UE_Modification_NW_TFT55 Support of automatic re-activation of the EPS bearer(s) during Network Initiated Detach even though UE has initiated a detach procedure with detach type set to “EPS detach” or “combined EPS/IMSI detach” 24.301, 5.5.2.2.4 Rel-8 no yes, no pc_Re_Attach_AfterDetachColl56 Support of Squal based cell reselection to UTRAN from E-UTRAN 25.304, 5.2.6.1.4a Rel-9 yes yes, no pc_Squal_based_CellReselection_to_UTRAN_from_E_UTRAN57 Support of Squal based cell reselection to E-UTRAN from UTRAN 36.304, 5.2.4.5 Rel-9 yes yes, no pc_Squal_based_CellReselection_to_E_UTRAN_from_UTRAN58 Support of CMAS message 36.331, 5.2.1.5 Rel-9 no yes, no pc_CMAS_message59 Void 60 Void 61 Void 62 Support of logged measurements in RRC_IDLE 36.306, 4.3.13.1 Rel-10 no yes, no pc_loggedMeasurementsIdle63 Support of standalone GNSS receiver to provide detailed location information in RRC measurement report and logged measurements in RRC_IDLE 36.306, 4.3.13.2 Rel-10 no yes, no pc_standaloneGNSS-Location64 Support of automatic re-activation of the EPS bearer(s) 24.301 Rel-8 yes yes, no pc_Automatic_EPS_Re_Attach65 Support of UTRAN ANR 25.306, 4.15 Rel-10 no yes, no pc_UTRAN ANR66 Void 67 Support of PWS upper layer 23.041 clause9.1.3.4.2 Rel-9 no yes, no pc_PWS_UpperLayer68 Support of automatic PDN connectivity in EUTRAN (i.e. UE upper layer provides PDN connectivity parameters) 24.301, 6.5.1.1 Rel-8 yes yes, no pc_Auto_PDN_Connectivity69 Support user initiated PLMN reselection in automatic mode 23.122 Rel-8 yes yes, no pc_UserInitiatedPLMN_Reselection70 Support of UL MIMO 36.306, clause 4.3.4.6 Rel-10 no yes, no pc_UL_MIMO71 Support of ESM Notification procedure "24.301,6.6.2" Rel-9 yes yes, no pc_ESM_Notification72 Support of sending concatenated multiple Short Message over SGs 23.272, 8.2.3a Rel-9 yes yes, no pc_SMS_SGs_Multi_MO73 Support TAU in connected mode 23.221, 7.2a Rel-8 no yes, no "pc_TAU_connected_in_IMSApplicable when configured to pc_voice_PS_1_CS_2 and pc_attach"74 Support TAU in idle mode 23.221, 7.2a Rel-8 no yes, no "pc_TAU_idle_in_IMSApplicable when configured to pc_voice_PS_1_CS_2 and pc_attach"75 Support of Intra Frequency Proximity Indication 36.306, clause 4.3.10.1 Rel-9 no yes, no pc_IntraFreq_ProximityIndication76 Support of Inter Frequency Proximity Indication 36.306, clause 4.3.10.2 Rel-9 no yes, no pc_InterFreq_ProximityIndication77 Support of UTRAN Proximity Indication 36.306, clause 4.3.10.3 Rel-9 no yes, no pc_UTRAN_ProximityIndication78 Support of Access Technology Indication in available PLMNs list 23.122, clause 4.4.3.1.2 Rel-8 yes yes, no pc_Available_PLMNs_AcT_Ind79 Support of Squal based cell reselection between E-UTRAN and GERAN "36.304, clause 5.2.4.5,45.008, clause 6.6.6" Rel-9 no yes, no pc_Squal_based_CellReselection_between_E_UTRAN_and_GERAN80 Support of AttachWithIMSI 24.368, 5.4 Rel-10 yes yes, no pc_AttachWithIMSI81 Support of T3412 extended value IE 24.301, 8.2.1.12, 8.2.26.15 Rel-10 yes yes, no pc_T3412Extended82 Void 83 Support of Low Access Priority indication 24.008 1.8 Rel-10 no yes, no pc_LAP84 Support of MinimumPeriodicSearchTimer 23.122, 4.4.3.3 Rel-10 no yes, no pc_MinimumPeriodicSearchTimer85 Support of delivery of rachReport upon request from the network 36.306, 4.3.12.1 Rel-9 yes yes, no pc_Rach_Report86 Support of Power Preference Indication "36.306 4.3.15.3, 36.331,5.6.10" Rel-11 no yes, no pc_PPI_Support87 Support of Epdcch "36.306, 4.3.4.1836.331, 6.3.6" Rel-11 no yes, no pc_ePDCCH88 Void 89 Void 90 Support of Low Access Priority Override 24.368, 5.9, 31.102, 4.2.94 Rel-11 no yes, no pc_LAP_override91 Support of Extended Access Barring Override 24.368, 5.10, 31.102, 4.2.94 Rel-11 no yes, no pc_EAB_override92 Support of UE radio bearer test mode for CSG proximity testing "36.5095.3.2.3" Rel-9 no yes, no pc_TestModeforCSGproximity93 Upon reception of ‘Daylight saving time’ information the UE stores/updates the daylight saving time 24.301, 8.2.13 Rel-8 yes yes, no pc_DaylightSavingTime94 Support of Radio Link Failure Report for inter-RAT MRO "36.306,clause 6.10.1" Rel-11 no yes, no pc_RLF_Report_for_inter-RAT_MRO95 Support of IPv4 23.221, 5.1 Rel-5 yes yes, no pc_IPv496 Support of IPv6 23.221, 5.1 Rel-5 yes yes, no pc_IPv697 Support of Automatic Mode EF_LRPLMSI PLMN Selection exception 23.122, 4.4.3.1 Rel-8 yes yes, no pc_PLMN_EF_LRPLMNSI_Automatic_Mode_Exception98 Support of Manual Mode PLMN Selection exception 23.122, 4.4.3.1 Rel-8 yes yes, no pc_PLMN_Manual_Mode_Exception99 Support of ZUC algorithm 33.401,5.1.3.2 Rel-11 no yes, no pc_ZUC100 Supports, upon configuration of si-RequestForHO by the network, acquisition of relevant information from a neighbouring UMTS cell by reading the SI of the neighbouring cell using autonomous gaps and reporting 36.306, 4.3.11.3 Rel-9 yes yes, no pc_SI_Neighbour_UMTS_Autonomous_Gaps101 Support of reception of requestedFrequencyBands 36.306, 4.3.5.6 Rel-11 no yes, no pc_ reqFreqBands102 Support of more than 128 CA Band Combinations 36.331, 5.6.3.3, 6.4 Rel-11 no yes, no pc_More_Than_128_CAbandComb103 Supports, upon configuration of si-RequestForHO by the network, acquisition of relevant information from a neighbouring intra-frequency cell by reading the SI of the neighbouring cell using autonomous gaps and reporting 36.306, 4.3.11.1 Rel-9 no yes, no pc_SI_Neighbour_intraFreq_Autonomous_Gaps104 Supports, upon configuration of si-RequestForHO by the network, acquisition of relevant information from a neighbouring inter-frequency cell by reading the SI of the neighbouring cell using autonomous gaps and reporting 36.306, 4.3.11.2 Rel-9 no yes, no pc_SI_Neighbour_interFreq_Autonomous_Gaps105 Support of Type B Half-duplex FDD operation "36.211, 6.2.536.306, 4.2.6" Rel-12 no yes, no "pc_FDD_TypeB_HalfDuplexOnly applicable for UE supporting Category 0. When set transmission scheduling is performed in accordance to Half-Duplex operation Type B else in accordance to Full-Duplex operation. "106 Void 107 Support of enhanced HARQ pattern for TTI bundling operation for FDD 36.306 4.3.4.27 Rel-12 no yes, no pc_eHARQ_Pattern_for_TTI_bundling108 Support of tdd-FDD-CA-PCellDuplex-r12 with the first bit setting to “1” 36.306, 4.3.4.28 Rel-12 no yes, no pc_tdd_FDD_CA_TDD_Pcell109 Support of tdd-FDD-CA-PCellDuplex-r12 with the second bit setting to “1” 36.306, 4.3.4.28 Rel-12 no yes, no pc_tdd_FDD_CA_FDD_Pcell110 Support of ProSe direct communication "36.3064.3.21.1" Rel-12 no yes, no "pc_commSupportedBands36.306, 4.3.21.1: If a UE supports sidelink communication on at least one band, the UE shall support sidelink communication transmission based on UE autonomous resource selection and eNB scheduled resource allocation."111 Support of ProSe direct discovery "36.3064.3.21.3" Rel-12 no yes, no pc_discSupportedBands112 Support of ProSe EPC level discovery "24.3347.2" Rel-12 no yes, no pc_Prose_EPC_Discovery113 Support of ProSe discovery SLSS transmission and reception 36.306, 4.3.21.6 Rel-12 no yes, no pc_discSLSSn114 Support of uplink 64QAM 36.306, 4.3.4.39 Rel-12 no yes, no 115 Support of Power Saving Mode 24.301, 5.3.11 Rel-12 no yes, no 116 Support of downlink 256QAM "36.306, 4.1, 4.1A" Rel-12 no yes, no Applicable for UEs of category 11-12 and UEs of DL category 11 and onwards. It is mandatory for UEs of DL category 13-14.117 Support for GSMA PRD IR.51: "IMS Profile for Voice, Video and SMS over Wi-Fi" "IEEE Std 802.11GSMA PRD IR.51" Rel-11 no yes, no pc_WLAN_voice118 Support of CSI-RS based discovery signals measurement 36.306 4.3.6.10 Rel-12 no yes, no pc_CSI-RS_DS_Meas119 Support of simultaneous transmission of EUTRA and sidelink communication (on different carriers) in all bands for which the UE indicated simultaneous sidelink and EUTRA support in a band combination (using commSupportedBandsPerBC) 36.306, 4.3.21.2 Rel-12 no yes, no pc_commSimultaneousTxTable A.4.4-1A Additional UE radio access capabilities (Mandatory for Rel-11 and onward) Reference Release Status Supported Allowed Comments1 UL Coordinated Multi-Point operation 36.306, 4.3.4.23 Rel-11 O.01 no yes, no "pc_UL_CoMPThis is a Rel-11 Mandatory feature"2 Support of TDD special subframe "36.306, 4.3.4.2136.331, 6.3.6" "Rel-11 : O.01Rel-9, Rel-10 : O" refer to Release no yes, no "pc_TDD_SpecialSubframeThis is a Rel-11 Mandatory featureThe Capability can optionally be implemented in UEs of the indicated Releases"3 Support of multiple timing advances for each band combination supported by the UE 36.306, 4.3.5.3 Rel-11 O.01 no yes, no "pc_multipleTimingAdvanceThis is a Rel-11 Mandatory feature (Note 3)"4 Support of Extended Access Barring 36.306, 7.3.1 Rel-11 O.01 no yes, no "pc_EABThis is a Rel-11 Mandatory feature (Note 4)"5 Support of transmission of discovery announcements based on network scheduled resource allocation. 36.306, 4.3.21.4 Rel-12 O.01 no yes, no "pc_discScheduledResourceAllocThis is a Rel-12 Mandatory feature (Note 5)"6 Support of transmission of discovery announcements based on UE autonomous resource selection. 36.306, 4.3.21.5 Rel-12 O.01 no yes, no "pc_discUESelectedResourceAllocThis is a Rel-12 Mandatory feature (Note 5)"Note "Note 1: From Rel-11 onwards 3GPP TSG RAN has discontinued the usage of FGI bits (see A.4.5). Instead it has introduced a different mechanism to accomplish the same purposes based on the following principles (TS 36.306 [1] clause 4): 'For optional features, the UE radio access capability parameter indicates whether the feature has been implemented and successfully tested. For mandatory features with the UE radio access capability parameter, the parameter indicates whether the feature has been successfully tested.'Reflecting this situation, in the present table the status for Mandatory features would be indicated as conditional Optional (O.xx) until IOT testing availability is ensured. The decision when IOT testing availability can be considered ensured is made by 3GPP TSG RAN. After the 3GPP TSG RAN decision that IOT testing is available the status of the capability parameter will be changed to Mandatory (M) and the release from which this requirement apply will be explicitly stated.Note 2: If indicated ""Yes"" the feature shall be implemented and successfully tested for the corresponding release.Note 3: It is mandatory for UEs of this release of the specification to support this capability for band combinations having an UL on multiple FDD bands (see 36.306, 4.3.5.3). In the context of evaluating the status of the capability this would depend on the indication for UL support provided in Table A.4.3.3.3-3 i.e. if for at least one CA configurations for Inter-band CA the UE indicates A-A then the Support of multiple timing advances for this CA configuration is Mandatory.Note 4: It is mandatory for UEs which are supporting an access subject to Extended Access Barring (see 36.306, 7.1.3).Note 5: It is mandatory for UEs which are supporting ProSe direct discovery.O.01 IF The feature has been IOT-ed THEN Support shall be indicated ELSE Support shall not be indicated" Table A.4.4-2 Definition of UE implementation capabilities Reference Release Status Supported Allowed Comments1 Support EPS attach (with or without pre-configuration) "24.301(Note 1)" Rel-8 no yes, no "pc_attachUE supports to be configured to initiate EPS attach or will always initiate EPS attach.(pc_PS_voice_centric OR pc_PS_data_centric) shall set this PICS to true."2 Support combined EPS/IMSI attach (with or without pre-configuration) 24.301 Rel-8 yes yes, no "pc_combined_attachUE supports to be configured to initiate combined EPS/IMSI attach or will always initiate combined EPS/IMSI attach.Implication:((pc_UTRA OR pc_GERAN) AND [8] pc_CS) OR pc_CS_fallback OR pc_SMS_SGs OR pc_IMSI_detach OR pc_CS_Em_Call_in_UTRA OR pc_CS_Em_Call_in_GERAN OR pc_CS_PS_voice_centric OR pc_CS_PS_data_centricshall set this PICS to true."3 Void 4 Support of CS/PS mode 1 24.301 Rel-8 yes yes, no "pc_CS_PS_voice_centricUE supports to be configured to consistently behave as a CS/PS Voice centric UE"5 Support of CS/PS mode 2 24.301 Rel-8 no yes, no "pc_CS_PS_data_centricUE supports to be configured to consistently behave as a CS/PS Data centric UE."6 Requiring UMI proceeding to paging response 23.272 Rel-8 yes yes, no "pc_UMI_ProcNeeded_DuringCSFBUE requires UMI prior to paging response while CSFB to UTRA"7 Support of PS mode 1 24.301 Rel-8 no yes, no "pc_PS_voice_centricUE supports to be configured to consistently behave as a PS Voice centric UE"8 Support of PS mode 2 24.301 Rel-8 no yes, no "pc_PS_data_centricUE supports to be configured to consistently behave as a PS Data centric UE."9 IMS PS voice preferred, CS Voice as secondary 24.301 Rel-8 no yes, no "pc_voice_PS_1_CS_2Configured voice domain preference."10 Keeps EPS Bearer Context parameters after completion of the normal DETACH procedure 24.301 cl. 5.5.2.2.2 Rel 8 no yes, no "pc_KeepEpsBearerParametersAfterNormalDetachIf the UE supports this, then the next ATTACH after DETACH shall be done using AT command AT+CGATT=1.Otherwise it shall be done usingAT+CGDCONT=1,""IP"" followed by AT+CGACT=1"11 IMS APN as default APN 23.401 Rel 8 no yes, no "pc_IMS_APN_defaultConfigured with IMS APN as default APN."12 XCAP only APN 23.401 Rel 8 no yes, no "pc_XCAP_only_APNConfigured with an APN for XCAP only usage.(Note 2)"13 Provide IMS APN 23.401 Rel 8 no yes, no "pc_Provide_IMS_APNConfigured to provide IMS APN during initial attach."14 Provide IMS as second APN 23.401 Rel 8 no yes, no "pc_Provide_IMS_as_second_APNConfigured to provide IMS APN as the second PDN connection."15 Provide Internet as second APN 23.401 Rel 8 no yes, no "pc_Provide_Internet_as_second_APNConfigured to provide Internet as the second PDN connection."16 User initiated PDN disconnect 24.301 Rel 8 no yes, no "pc_UE_supports_user_initiated_PDN_disconnectUE supports user initiated PDN disconnect."17 XCAP over Internet PDN 23.401 Rel 8 yes yes, no "pc_XCAP_over_Internet_APNConfigured to use internet PDN for XCAP signalling (Note 2)"18 Dynamically downgrades the GERAN release when the support of EPS is disabled 24.301, 24.008 Rel 8 no yes, no "pc_Dynamic_GERAN_Rel_downgradeUE may support e.g. from all GERAN Rel-8 features only those related to the interworking with EPS. When EPS is disabled then the Device may comply with a lower than Rel-8 GERAN release requirements."19 Provide ProSe APN 24.334 Rel-12 no yes, no "Configured to provide ProSe APN and a PDN connection request.An UE supporting D2D ProSe shall set this PICS to true."20 Provisioned FQDN ePDG 24.302 Rel-13 no yes, no "pc_ePDG_FQDN_ProvisionedConfigured with an ePDG FQDN provisioned by the home operator."21 Operator Identifier FQDN format used for ePDG 24.302 Rel-13 no yes, no "pc_ePDG_FQDN_constructedConfigured to construct the ePDG FQDN in the Operator Identifier FQDN format."Note "Note 1: A UE supporting UTRAN and/or GERAN which is configured to initiate EPS attach considers UTRAN and GERAN cell as candidates for cell selection and cell reselection according to TS 36.304. A UE configured to initiate EPS attach which has selected a UTRAN or GERAN cell may perform registration procedures to the PS and CS domains, or to the PS domain only or to the CS domain only.Note 2: pc_XCAP_only_APN and pc_XCAP_over_Internet_APN are mutual exclusive i.e. shall not be set to true at the same time." Table A.4.5-1 Void Reference Release Status Supported Allowed CommentsTable A.4.5-1a Feature group indicators 1-32 for FDD Reference Release Status Supported Allowed Comments1 "Support of- Intra-subframe frequency hopping for PUSCH scheduled by UL grant- DCI format 3a (TPC commands for PUCCH and PUSCH with single bit power adjustments)- Aperiodic CQI/PMI/RI reporting on PUSCH: Mode 2-0 – UE selected subband CQI without PMI- Aperiodic CQI/PMI/RI reporting on PUSCH: Mode 2-2 – UE selected subband CQI with multiple PMI" 36.331, Annex B.1 Rel-8 yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 1.Set to true if supporting all functionalities in the feature group."2 "Support of- Simultaneous CQI and ACK/NACK on PUCCH, i.e. PUCCH format 2a and 2b- Absolute TPC command for PUSCH- Resource allocation type 1 for PDSCH- Periodic CQI/PMI/RI reporting on PUCCH: Mode 2-0 – UE selected subband CQI without PMI- Periodic CQI/PMI/RI reporting on PUCCH: Mode 2-1 – UE selected subband CQI with single PMI" 36.331, Annex B.1 Rel-8 yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 2.Set to true if supporting all functionalities in the feature group."3 "Support of- Semi-persistent scheduling- TTI bundling- 5bit RLC UM SN- 7bit PDCP SNSupport of- 5bit RLC UM SN- 7bit PDCP SN" 36.331, Annex B.1 "Rel-8Rel-9, Rel-10Rel-11" yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 3.Set to true if supporting all functionalities in the feature group.If UE supports FDD and TDD this item shall be set to same value as for item 3 in Table A.4.5-1b for TDD.- can only be set to 1 if the UE has set bit number 7 to 1.Yes, if UE supports VoLTE and Rel9, Rel10Yes, if UE supports VoLTE and Rel11.Yes, if UE supports SRVCC to EUTRAN from GERAN and Rel11."4 "Support of- Short DRX cycle" 36.331, Annex B.1 Rel-8 yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 4.Set to true if supporting all functionalities in the feature group.- can only be set to 1 if the UE has set bit number 5 to 1."5 "Support of- Long DRX cycle- DRX command MAC control element" 36.331, Annex B.1 "Rel-8Rel-9" yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 5.Set to true if supporting all functionalities in the feature group.If UE supports FDD and TDD this item shall be set to same value as for item 5 in Table A.4.5-1b for TDD.Yes, if UE supports Rel9"6 "Support of- Prioritized bit rate" 36.331, Annex B.1 "Rel-8Rel-9" yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 6.Set to true if supporting all functionalities in the feature group.If UE supports FDD and TDD this item shall be set to same value as for item 6 in Table A.4.5-1b for TDD.Yes, if UE supports Rel9"7 "Support of- RLC UM" 36.331, Annex B.1 "Rel-8Rel-9, Rel-10Rel-11" yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 7.Set to true if supporting all functionalities in the feature group.If UE supports FDD and TDD this item shall be set to same value as for item 7 in Table A.4.5-1b for TDD.- can only be set to 0 if the UE does not support voiceYes, if UE supports VoLTE and Rel9, Rel10Yes, if UE supports VoLTE and Rel11.Yes, if UE supports SRVCC to EUTRAN from GERAN and Rel11."8 "Support of- EUTRA RRC_CONNECTED to UTRA CELL_DCH PS handoverSupport of- EUTRA RRC_CONNECTED to UTRA FDD or UTRA TDD CELL_DCH PS handover, if the UE supports either only UTRAN FDD or only UTRAN TDD - EUTRA RRC_CONNECTED to UTRA FDD CELL_DCH PS handover, if the UE supports both UTRAN FDD and UTRAN TDD" 36.331, Annex B.1 "Rel-8Rel-9" yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 8.Set to true if supporting all functionalities in the feature group.- can only be set to 1 if the UE has set bit number 22 to 1Yes, if UE supports UTRA"9 "Support of- EUTRA RRC_CONNECTED to GERAN GSM_Dedicated handover" 36.331, Annex B.1 "Rel-8 to Rel-10Rel-11" no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 9.Set to true if supporting all functionalities in the feature group.- related to SR-VCC- can only be set to 1 if the UE has set bit number 23 to 1Yes, if UE supports SRVCC to EUTRAN from GERAN and Rel11."10 "Support of- EUTRA RRC_CONNECTED to GERAN (Packet_)Idle by Cell Change Order- EUTRA RRC_CONNECTED to GERAN (Packet_)Idle by Cell Change Order with NACC (Network Assisted Cell Change)" 36.331, Annex B.1 Rel-8 yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 10.Set to true if supporting all functionalities in the feature group."11 "Support of- EUTRA RRC_CONNECTED to CDMA2000 1xRTT CS Active handover" 36.331, Annex B.1 Rel-8 no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 11.Set to true if supporting all functionalities in the feature group.- can only be set to 1 if the UE has sets bit number 24 to 1"12 "Support of- EUTRA RRC_CONNECTED to CDMA2000 HRPD Active handover" 36.331, Annex B.1 Rel-8 no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 12.Set to true if supporting all functionalities in the feature group.- can only be set to 1 if the UE has set bit number 26 to 1"13 "Support of- Inter-frequency handover (within FDD or TDD)" 36.331, Annex B.1 "Rel-8Rel-9" yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 13.Set to true if supporting all functionalities in the feature group.If UE supports FDD and TDD this item shall be set to same value as for item 13 in Table A.4.5-1b for TDD.- can only be set to 1 if the UE has set bit number 25 to 1Yes, unless UE only supports band 13"14 "Support of- Measurement reporting event: Event A4 – Neighbour > threshold- Measurement reporting event: Event A5 – Serving < threshold1 & Neighbour > threshold2" 36.331, Annex B.1 "Rel-8Rel-9" yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 14.Set to true if supporting all functionalities in the feature group.If UE supports FDD and TDD this item shall be set to same value as for item 14 in Table A.4.5-1b for TDD."15 "Support of- Measurement reporting event: Event B1 - Neighbour > threshold for UTRAN FDD or UTRAN TDD, if the UE supports either only UTRAN FDD or only UTRAN TDD and has set bit number 22 to 1- Measurement reporting event: Event B1 - Neighbour > threshold for UTRAN FDD or UTRAN TDD, if the UE supports both UTRAN FDD and UTRAN TDD and has set bit number 22 or 39 to 1, respectively- Measurement reporting event: Event B1 - Neighbour > threshold for GERAN, 1xRTT or HRPD, if the UE has set bit number 23, 24 or 26 to 1, respectively" 36.331, Annex B.1 "Rel-8Rel-9" yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 15.Set to true if supporting all functionalities in the feature group.- can only be set to 1 if the UE has set at least one of the bit number 22, 23, 24, 26 or 39 to 1.- even if the UE sets bits 41, it shall still set bit 15 to 1 if measurement reporting event B1 is tested for all RATs supported by UEYes for FDD, if UE supports only UTRAN FDD and does not support UTRAN TDD or GERAN or 1xRTT or HRPD"16 "Support of- Intra-frequency periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells;- Inter-frequency periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells, if the UE has set bit number 25 to 1; and- Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells for UTRAN, GERAN, 1xRTT or HRPD, if the UE has set bit number 22, 23, 24 or 26 to 1, respectivelyNOTE: Event triggered periodical reporting (i.e. with triggerType set to event and with reportAmount > 1) is a mandatory functionality of event triggered reporting and therefore not the subject of this bit.Support of- Intra-frequency periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells- Inter-frequency periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells, if the UE has set bit number 25 to 1- Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells for UTRAN FDD or UTRAN TDD, if the UE supports either only UTRAN FDD or only UTRAN TDD and has set bit number 22 to 1- Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells for UTRAN FDD or UTRAN TDD, if the UE supports both UTRAN FDD and UTRAN TDD and has set bit number 22 or 39 to 1, respectively- Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells for GERAN, 1xRTT or HRPD, if the UE has set bit number 23, 24 or 26 to 1, respectivelyNOTE: Event triggered periodical reporting (i.e., with triggerType set to event and with reportAmount > 1) is a mandatory functionality of event triggered reporting and therefore not the subject of this bit." 36.331, Annex B.1 "Rel-8Rel-9" yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 16.Set to true if supporting all functionalities in the feature group.If UE supports FDD and TDD this item shall be set to same value as for item 16 in Table A.4.5-1b for TDD.Yes, if UE supports Rel9"17 "Support ofIntra-frequency ANR features including:- Intra-frequency periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells- Intra-frequency periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI" 36.331, Annex B.1 "Rel-8Rel-9" yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 17.Set to true if supporting all functionalities in the feature group.If UE supports FDD and TDD this item shall be set to same value as for item 17 in Table A.4.5-1b for TDD.- can only be set to 1 if the UE has set bit number 5 to 1Yes, if UE supports Rel9"18 "Support ofInter-frequency ANR features including:- Inter-frequency periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells- Inter-frequency periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI" 36.331, Annex B.1 "Rel-8Rel-9" yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 18.Set to true if supporting all functionalities in the feature group.If UE supports FDD and TDD this item shall be set to same value as for item 18 in Table A.4.5-1b for TDD.- can only be set to 1 if the UE has set bit number 5 to 1.Yes, unless UE only supports band 13"19 "Support ofInter-RAT ANR features including:- Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells for GERAN, if the UE has set bit number 23 to 1- Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCellsForSON for UTRAN, 1xRTT or HRPD, if the UE has set bit number 22, 24 or 26 to 1, respectively- Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI for UTRAN, GERAN, 1xRTT or HRPD, if the UE has set bit number 22, 23, 24 or 26 to 1, respectivelySupport ofInter-RAT ANR features including:- Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells for GERAN, if the UE has set bit number 23 to 1- Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCellsForSON for UTRAN FDD or UTRAN TDD, if the UE supports either only UTRAN FDD or only UTRAN TDD and has set bit number 22 to 1- Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCellsForSON for UTRAN FDD or UTRAN TDD, if the UE supports both UTRAN FDD and UTRAN TDD and has set bit number 22 or 39 to 1, respectively- Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCellsForSON for 1xRTT or HRPD, if the UE has set bit number 24 or 26 to 1, respectively- Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI for UTRAN FDD or UTRAN TDD, if the UE supports either only UTRAN FDD or only UTRANTDD and has set bit number 22 to 1 - Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI for UTRAN FDD or UTRAN TDD, if the UE supports both UTRAN FDD and UTRAN TDD and has set bit number 22 or 39 to 1, respectively- Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI for GERAN, 1xRTT or HRPD, if the UE has set bit number 23, 24 or 26 to 1, respectively" 36.331, Annex B.1 "Rel-8Rel-9" yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 19.Set to true if supporting all functionalities in the feature group.- can only be set to 1 if the UE has set bit number 5 to 1 and the UE has set at least one of the bit number 22, 23, 24 or 26 to 1.- even if the UE sets bits 33 to 36, it shall still set bit 19 to 1 if inter-RAT ANR features are tested for all RATs for which inter-RAT measurement reporting is indicated as tested"20 "If bit number 7 is set to ‘0’:- SRB1 and SRB2 for DCCH + 8x AM DRBIf bit number 7 is set to ‘1’:- SRB1 and SRB2 for DCCH + 8x AM DRB- SRB1 and SRB2 for DCCH + 5x AM DRB + 3x UM DRBNOTE: UE which indicate support for a DRB combination also support all subsets of the DRB combination. Therefore, release of DRB(s) never results in an unsupported DRB combination." 36.331, Annex B.1 "Rel-8Rel-9" yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 20.Set to true if supporting all functionalities in the feature group.If UE supports FDD and TDD this item shall be set to same value as for item 20 in Table A.4.5-1b for TDD.- Regardless of what bit number 7 and bit number 20 is set to, UE shall support at least SRB1 and SRB2 for DCCH + 4x AM DRB- Regardless of what bit number 20 is set to, if bit number 7 is set to ‘1’, UE shall support at least SRB1 and SRB2 for DCCH + 4x AM DRB + 1x UM DRBYes, if UE supports Rel9"21 "Support of- Predefined intra- and inter-subframe frequency hopping for PUSCH with N_sb > 1- Predefined inter-subframe frequency hopping for PUSCH with N_sb > 1" 36.331, Annex B.1 Rel-8 yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 21.Set to true if supporting all functionalities in the feature group.If UE supports FDD and TDD this item shall be set to same value as for item 21 in Table A.4.5-1b for TDD."22 "Support of- UTRAN measurements, reporting and measurement reporting event B2 in E-UTRA connected modeSupport of- UTRAN FDD or UTRAN TDD measurements, reporting and measurement reporting event B2 in E-UTRA connected mode, if the UE supports either only UTRAN FDD or only UTRAN TDD- UTRAN FDD measurements, reporting and measurement reporting event B2 in E-UTRA connected mode, if the UE supports both UTRAN FDD and UTRAN TDD" 36.331, Annex B.1 "Rel-8Rel-9" yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 22.Set to true if supporting all functionalities in the feature group.Yes, if UE supports UTRA and Rel9"23 "Support of- GERAN measurements, reporting and measurement reporting event B2 in E-UTRA connected mode" 36.331, Annex B.1 Rel-8 yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 23.Set to true if supporting all functionalities in the feature group."24 "Support of- 1xRTT measurements, reporting and measurement reporting event B2 in E-UTRA connected mode" 36.331, Annex B.1 "Rel-8Rel-9" no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 24.Set to true if supporting all functionalities in the feature group.Yes, if UE supports enhanced 1xRTT CSFB"25 "Support of- Inter-frequency measurements and reporting in E-UTRA connected modeNOTE: The UE setting this bit to 1 and indicating support for FDD and TDD frequency bands in the UE capability signalling implements and is tested for FDD measurements while the UE is in TDD, and for TDD measurements while the UE is in FDD." 36.331, Annex B.1 "Rel-8Rel-9" yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 25.Set to true if supporting all functionalities in the feature group.If UE supports FDD and TDD this item shall be set to same value as for item 25 in Table A.4.5-1b for TDD.Yes, unless UE only supports band 13"26 "Support of- HRPD measurements, reporting and measurement reporting event B2 in E-UTRA connected mode" 36.331, Annex B.1 "Rel-8Rel-9" no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 26.Set to true if supporting all functionalities in the feature group.Yes, if UE supports HRPD"27 "Support of- EUTRA RRC_CONNECTED to UTRA CELL_DCH CS handoverSupport of- EUTRA RRC_CONNECTED to UTRA FDD or UTRA TDD CELL_DCH CS handover, if the UE supports either only UTRAN FDD or only UTRAN TDD- EUTRA RRC_CONNECTED to UTRA FDD CELL_DCH CS handover, if the UE supports both UTRAN FDD and UTRAN TDD" 36.331, Annex B.1 "Rel-8Rel-9" no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 27.Set to true if supporting all functionalities in the feature group.- related to SR-VCC- can only be set to 1 if the UE has set bit number 8 to 1 and supports SR-VCC from EUTRA defined in TS 24.008Yes for FDD, if UE supports VoLTE and UTRA FDD and Rel9"28 "Support of- TTI bundling" 36.331, Annex B.1 Rel-9 yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 28.Set to true if supporting all functionalities in the feature group.Yes, if UE supports Rel9"29 "Support of- Semi-Persistent Scheduling" 36.331, Annex B.1 Rel-9 yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 29.Set to true if supporting all functionalities in the feature group."30 "Support of- Handover between FDD and TDD" 36.331, Annex B.1 Rel-8 yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 30.Set to true if supporting all functionalities in the feature group.If UE supports FDD and TDD this item shall be set to same value as for item 30 in Table A.4.5-1b for TDD.- can only be set to 1 if the UE has set bit number 13 to 1"31 "Support of- Indicates whether the UE supports the mechanisms defined for cells broadcasting multi band information i.e. comprehending multiBandInfoList, disregarding in RRC_CONNECTED the related system information fields and understanding the EARFCN signalling for all bands, that overlap with the bands supported by the UE, and that are defined in the earliest version of TS 36.101 [42] that includes all UE supported bands." 36.331, Annex B.1 "Rel-8Rel-10" yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 31.Set to true if supporting all functionalities in the feature group.If UE supports FDD and TDD this item shall be set to same value as for item 31 in Table A.4.5-1b for TDD.Yes, if UE supports Rel10"32 Undefined 36.331, Annex B.1 Rel-8 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 32.Table A.4.5-1b Feature group indicators 1-32 for TDD Reference Release Status Supported Allowed Comments1 "Support of- Intra-subframe frequency hopping for PUSCH scheduled by UL grant- DCI format 3a (TPC commands for PUCCH and PUSCH with single bit power adjustments)- Aperiodic CQI/PMI/RI reporting on PUSCH: Mode 2-0 – UE selected subband CQI without PMI- Aperiodic CQI/PMI/RI reporting on PUSCH: Mode 2-2 – UE selected subband CQI with multiple PMI" 36.331, Annex B.1 Rel-8 yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 1.Set to true if supporting all functionalities in the feature group."2 "Support of- Simultaneous CQI and ACK/NACK on PUCCH, i.e. PUCCH format 2a and 2b- Absolute TPC command for PUSCH- Resource allocation type 1 for PDSCH- Periodic CQI/PMI/RI reporting on PUCCH: Mode 2-0 – UE selected subband CQI without PMI- Periodic CQI/PMI/RI reporting on PUCCH: Mode 2-1 – UE selected subband CQI with single PMI" 36.331, Annex B.1 Rel-8 yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 2.Set to true if supporting all functionalities in the feature group."3 "Support of- Semi-persistent scheduling- TTI bundling- 5bit RLC UM SN- 7bit PDCP SNSupport of- 5bit RLC UM SN- 7bit PDCP SN" 36.331, Annex B.1 "Rel-8Rel-9, Rel-10Rel-11" yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 3.Set to true if supporting all functionalities in the feature group.If UE supports FDD and TDD this item shall be set to same value as for item 3 in Table A.4.5-1a for FDD.- can only be set to 1 if the UE has set bit number 7 to 1.Yes, if UE supports VoLTE and Rel9, Rel10Yes, if UE supports VoLTE and Rel11.Yes, if UE supports SRVCC to EUTRAN from GERAN and Rel11."4 "Support of- Short DRX cycle" 36.331, Annex B.1 Rel-8 yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 4.Set to true if supporting all functionalities in the feature group.- can only be set to 1 if the UE has set bit number 5 to 1."5 "Support of- Long DRX cycle- DRX command MAC control element" 36.331, Annex B.1 "Rel-8Rel-9" yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 5.Set to true if supporting all functionalities in the feature group.If UE supports FDD and TDD this item shall be set to same value as for item 5 in Table A.4.5-1a for FDD.Yes, if UE supports Rel9"6 "Support of- Prioritized bit rate" 36.331, Annex B.1 "Rel-8Rel-9" yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 6.Set to true if supporting all functionalities in the feature group.If UE supports FDD and TDD this item shall be set to same value as for item 6 in Table A.4.5-1a for FDD.Yes, if UE supports Rel9"7 "Support of- RLC UM" 36.331, Annex B.1 "Rel-8Rel-9, Rel-10Rel-11" yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 7.Set to true if supporting all functionalities in the feature group.If UE supports FDD and TDD this item shall be set to same value as for item 7 in Table A.4.5-1a for FDD.- can only be set to 0 if the UE does not support voiceYes, if UE supports VoLTE and Rel9, Rel10Yes, if UE supports VoLTE and Rel11.Yes, if UE supports SRVCC to EUTRAN from GERAN and Rel11."8 "Support of- EUTRA RRC_CONNECTED to UTRA FDD or UTRA TDD CELL_DCH PS handover, if the UE supports either only UTRAN FDD or only UTRAN TDD- EUTRA RRC_CONNECTED to UTRA FDD CELL_DCH PS handover, if the UE supports both UTRAN FDD and UTRAN TDD" 36.331, Annex B.1 Rel-8 yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 8.Set to true if supporting all functionalities in the feature group.- can only be set to 1 if the UE has set bit number 22 to 1"9 "Support of- EUTRA RRC_CONNECTED to GERAN GSM_Dedicated handover" 36.331, Annex B.1 "Rel-8 to Rel-10Rel-11" no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 9.Set to true if supporting all functionalities in the feature group.- related to SR-VCC- can only be set to 1 if the UE has set bit number 23 to 1Yes, if UE supports SRVCC to EUTRAN from GERAN and Rel11."10 "Support of- EUTRA RRC_CONNECTED to GERAN (Packet_)Idle by Cell Change Order- EUTRA RRC_CONNECTED to GERAN (Packet_)Idle by Cell Change Order with NACC (Network Assisted Cell Change)" 36.331, Annex B.1 Rel-8 yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 10.Set to true if supporting all functionalities in the feature group."11 "Support of- EUTRA RRC_CONNECTED to CDMA2000 1xRTT CS Active handover" 36.331, Annex B.1 Rel-8 no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 11.Set to true if supporting all functionalities in the feature group.- can only be set to 1 if the UE has sets bit number 24 to 1"12 "Support of- EUTRA RRC_CONNECTED to CDMA2000 HRPD Active handover" 36.331, Annex B.1 Rel-8 no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 12.Set to true if supporting all functionalities in the feature group.- can only be set to 1 if the UE has set bit number 26 to 1"13 "Support of- Inter-frequency handover (within FDD or TDD)" 36.331, Annex B.1 "Rel-8Rel-9" yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 13.Set to true if supporting all functionalities in the feature group.If UE supports FDD and TDD this item shall be set to same value as for item 13 in Table A.4.5-1a for FDD.- can only be set to 1 if the UE has set bit number 25 to 1Yes, unless UE only supports band 13"14 "Support of- Measurement reporting event: Event A4 – Neighbour > threshold- Measurement reporting event: Event A5 – Serving < threshold1 & Neighbour > threshold2" 36.331, Annex B.1 "Rel-8Rel-9" yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 14.Set to true if supporting all functionalities in the feature group.If UE supports FDD and TDD this item shall be set to same value as for item 14 in Table A.4.5-1a for FDD.Yes, if UE supports Rel9"15 "Support of- Measurement reporting event: Event B1 - Neighbour > threshold for UTRAN FDD or UTRAN TDD, if the UE supports either only UTRAN FDD or only UTRAN TDD and has set bit number 22 to 1- Measurement reporting event: Event B1 - Neighbour > threshold for UTRAN FDD or UTRAN TDD, if the UE supports both UTRAN FDD and UTRAN TDD and has set bit number 22 or 39 to 1, respectively- Measurement reporting event: Event B1 - Neighbour > threshold for GERAN, 1xRTT or HRPD, if the UE has set bit number 23, 24 or 26 to 1, respectively" 36.331, Annex B.1 Rel-8 yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 15.Set to true if supporting all functionalities in the feature group.- can only be set to 1 if the UE has set at least one of the bit number 22, 23, 24, 26 or 39 to 1.- even if the UE sets bits 41, it shall still set bit 15 to 1 if measurement reporting event B1 is tested for all RATs supported by UE"16 "Support of- Intra-frequency periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells;- Inter-frequency periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells, if the UE has set bit number 25 to 1; and- Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells for UTRAN, GERAN, 1xRTT or HRPD, if the UE has set bit number 22, 23, 24 or 26 to 1, respectivelyNOTE: Event triggered periodical reporting (i.e. with triggerType set to event and with reportAmount > 1) is a mandatory functionality of event triggered reporting and therefore not the subject of this bit.Support of- Intra-frequency periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells;- Inter-frequency periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells, if the UE has set bit number 25 to 1- Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells for UTRAN FDD or UTRAN TDD, if the UE supports either only UTRAN FDD or only UTRAN TDD and has set bit number 22 to 1- Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells for UTRAN FDD or UTRAN TDD, if the UE supports both UTRAN FDD and UTRAN TDD and has set bit number 22 or 39 to 1, respectively- Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells for GERAN, 1xRTT or HRPD, if the UE has set bit number 23, 24 or 26 to 1, respectivelyNOTE: Event triggered periodical reporting (i.e. with triggerType set to event and with reportAmount > 1) is a mandatory functionality of event triggered reporting and therefore not the subject of this bit." 36.331, Annex B.1 "Rel-8Rel-9" yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 16.Set to true if supporting all functionalities in the feature group.If UE supports FDD and TDD this item shall be set to same value as for item 16 in Table A.4.5-1a for FDD.Yes, if UE supports Rel9"17 "Support ofIntra-frequency ANR features including:- Intra-frequency periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells- Intra-frequency periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI" 36.331, Annex B.1 "Rel-8Rel-9" yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 17.Set to true if supporting all functionalities in the feature group.If UE supports FDD and TDD this item shall be set to same value as for item 17 in Table A.4.5-1a for FDD.- can only be set to 1 if the UE has set bit number 5 to 1.Yes, if UE supports Rel9"18 "Support ofInter-frequency ANR features including:- Inter-frequency periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells- Inter-frequency periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI" 36.331, Annex B.1 "Rel-8Rel-9" yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 18.Set to true if supporting all functionalities in the feature group.If UE supports FDD and TDD this item shall be set to same value as for item 18 in Table A.4.5-1a for FDD.- can only be set to 1 if the UE has set bit number 5 to 1.Yes, unless UE only supports band 13"19 "Support ofInter-RAT ANR features including:- Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells for GERAN, if the UE has set bit number 23 to 1- Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCellsForSON for UTRAN, 1xRTT or HRPD, if the UE has set bit number 22, 24 or 26 to 1, respectively- Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI for UTRAN, GERAN, 1xRTT or HRPD, if the UE has set bit number 22, 23, 24 or 26 to 1, respectivelySupport ofInter-RAT ANR features including:- Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells for GERAN, if the UE has set bit number 23 to 1- Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCellsForSON for UTRAN FDD or UTRAN TDD, if the UE supports either only UTRAN FDD or only UTRAN TDD and has set bit number 22 to 1- Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCellsForSON for UTRAN FDD or UTRAN TDD, if the UE supports both UTRAN FDD and UTRAN TDD and has set bit number 22 or 39 to 1, respectively- Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCellsForSON for 1xRTT or HRPD, if the UE has set bit number 24 or 26 to 1, respectively." 36.331, Annex B.1 "Rel-8Rel-9" yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 19.Set to true if supporting all functionalities in the feature group.- can only be set to 1 if the UE has set bit number 5 to 1 and the UE has set at least one of the bit number 22, 23, 24 or 26 to 1.- even if the UE sets bits 33 to 36, it shall still set bit 19 to 1 if inter-RAT ANR features are tested for all RATs for which inter-RAT measurement reporting is indicated as tested"20 "If bit number 7 is set to ‘0’:- SRB1 and SRB2 for DCCH + 8x AM DRBIf bit number 7 is set to ‘1’:- SRB1 and SRB2 for DCCH + 8x AM DRB- SRB1 and SRB2 for DCCH + 5x AM DRB + 3x UM DRBNOTE: UE which indicate support for a DRB combination also support all subsets of the DRB combination. Therefore, release of DRB(s) never results in an unsupported DRB combination." 36.331, Annex B.1 "Rel-8Rel-9" yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 20.Set to true if supporting all functionalities in the feature group.If UE supports FDD and TDD this item shall be set to same value as for item 20 in Table A.4.5-1a for FDD.- Regardless of what bit number 7 and bit number 20 is set to, UE shall support at least SRB1 and SRB2 for DCCH + 4x AM DRB- Regardless of what bit number 20 is set to, if bit number 7 is set to ‘1’, UE shall support at least SRB1 and SRB2 for DCCH + 4x AM DRB + 1x UM DRBYes, if UE supports Rel9"21 "Support of- Predefined intra- and inter-subframe frequency hopping for PUSCH with N_sb > 1- Predefined inter-subframe frequency hopping for PUSCH with N_sb > 1" 36.331, Annex B.1 Rel-8 yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 21.Set to true if supporting all functionalities in the feature group.If UE supports FDD and TDD this item shall be set to same value as for item 21 in Table A.4.5-1a for FDD."22 "Support of- UTRAN measurements, reporting and measurement reporting event B2 in E-UTRA connected modeSupport of- UTRAN FDD or UTRAN TDD measurements, reporting and measurement reporting event B2 in E-UTRA connected mode, if the UE supports either only UTRAN FDD or only UTRAN TDD- UTRAN FDD measurements, reporting and measurement reporting event B2 in E-UTRA connected mode, if the UE supports both UTRAN FDD and UTRAN TDD" 36.331, Annex B.1 "Rel-8Rel-9" yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 22.Set to true if supporting all functionalities in the feature group."23 "Support of- GERAN measurements, reporting and measurement reporting event B2 in E-UTRA connected mode" 36.331, Annex B.1 Rel-8 yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 23.Set to true if supporting all functionalities in the feature group."24 "Support of- 1xRTT measurements, reporting and measurement reporting event B2 in E-UTRA connected mode" 36.331, Annex B.1 "Rel-8Rel-9" no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 24.Set to true if supporting all functionalities in the feature group.Yes, if UE supports enhanced 1xRTT CSFB"25 "Support of- Inter-frequency measurements and reporting in E-UTRA connected modeNOTE: The UE setting this bit to 1 and indicating support for FDD and TDD frequency bands in the UE capability signalling implements and is tested for FDD measurements while the UE is in TDD, and for TDD measurements while the UE is in FDD." 36.331, Annex B.1 "Rel-8Rel-9" yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 25.Set to true if supporting all functionalities in the feature group.If UE supports FDD and TDD this item shall be set to same value as for item 25 in Table A.4.5-1a for FDD.Yes, unless UE only supports band 13"26 "Support of- HRPD measurements, reporting and measurement reporting event B2 in E-UTRA connected mode" 36.331, Annex B.1 "Rel-8Rel-9" no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 26.Set to true if supporting all functionalities in the feature group."27 "Support of- EUTRA RRC_CONNECTED to UTRA CELL_DCH CS handoverSupport of- EUTRA RRC_CONNECTED to UTRA FDD or UTRA TDD CELL_DCH CS handover, if the UE supports either only UTRAN FDD or only UTRAN TDD- EUTRA RRC_CONNECTED to UTRA FDD CELL_DCH CS handover, if the UE supports both UTRAN FDD and UTRAN TDD" 36.331, Annex B.1 "Rel-8Rel-9" no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 27.Set to true if supporting all functionalities in the feature group.- related to SR-VCC- can only be set to 1 if the UE has set bit number 8 to 1 and supports SR-VCC from EUTRA defined in TS 24.008"28 "Support of- TTI bundling" 36.331, Annex B.1 Rel-9 yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 28.Set to true if supporting all functionalities in the feature group."29 "Support of- Semi-Persistent Scheduling" 36.331, Annex B.1 Rel-9 yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 29.Set to true if supporting all functionalities in the feature group."30 "Support of- Handover between FDD and TDD" 36.331, Annex B.1 Rel-8 yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 30.Set to true if supporting all functionalities in the feature group.If UE supports FDD and TDD this item shall be set to same value as for item 30 in Table A.4.5-1a for FDD.- can only be set to 1 if the UE has set bit number 13 to 1"31 "Support of- Indicates whether the UE supports the mechanisms defined for cells broadcasting multi band information i.e. comprehending multiBandInfoList, disregarding in RRC_CONNECTED the related system information fields and understanding the EARFCN signalling for all bands, that overlap with the bands supported by the UE, and that are defined in the earliest version of TS 36.101 [42] that includes all UE supported bands." 36.331, Annex B.1 "Rel-8Rel-10" yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 31.Set to true if supporting all functionalities in the feature group.If UE supports FDD and TDD this item shall be set to same value as for item 31 in Table A.4.5-1a for FDD.Yes, if UE supports Rel10"32 Undefined 36.331, Annex B.1 Rel-8 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 32.Table A.4.5-1c Void Reference Release Status Supported Allowed CommentsTable A.4.5-1d Feature group indicators 33-64 for FDD Reference Release Status Supported Allowed Comments1 "Inter-RAT ANR features for UTRAN including:- Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCellsForSON- Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI" 36.331, Annex B.1 Rel-9 yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 33.Set to true if supporting all functionalities in the feature group.- can only be set to 1 if the UE has set bit number 5 and bit number 22 to 1."2 "Inter-RAT ANR features for GERAN including:- Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells- Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI" 36.331, Annex B.1 Rel-9 yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 34.Set to true if supporting all functionalities in the feature group.- can only be set to 1 if the UE has set bit number 5 and bit number 23 to 1."3 "Inter-RAT ANR features for 1xRTT including:- Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCellsForSON- Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI" 36.331, Annex B.1 Rel-9 no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 35.Set to true if supporting all functionalities in the feature group.- can only be set to 1 if the UE has set bit number 5 and bit number 24 to 1."4 "Inter-RAT ANR features for HRPD including:- Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCellsForSON- Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI" 36.331, Annex B.1 Rel-9 no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 36.Set to true if supporting all functionalities in the feature group.- can only be set to 1 if the UE has set bit number 5 and bit number 26 to 1."5 "Inter-RAT ANR features for UTRAN TDD including:- Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCellsForSON- Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI" 36.331, Annex B.1 Rel-9 no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 37.Set to true if supporting all functionalities in the feature group.- can only be set to 1 if the UE has set bit number 5 and at least one of the bit number 22 (for UEs supporting only UTRA TDD) or the bit number 39 to 1."6 - EUTRA RRC_CONNECTED to UTRA TDD CELL_DCH PS handover, if the UE supports both UTRAN FDD and UTRAN TDD 36.331, Annex B.1 Rel-9 no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 38.Set to true if supporting all functionalities in the feature group.- can only be set to 1 if the UE has set bit number 39 to 1."7 - UTRAN TDD measurements, reporting and measurement reporting event B2 in E-UTRA connected mode, if the UE supports both UTRAN FDD and UTRAN TDD 36.331, Annex B.1 Rel-9 no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 39.Set to true if supporting all functionalities in the feature group."8 - EUTRA RRC_CONNECTED to UTRA TDD CELL_DCH CS handover, if the UE supports both UTRAN FDD and UTRAN TDD 36.331, Annex B.1 Rel-9 no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 40.Set to true if supporting all functionalities in the feature group.- related to SR-VCC- can only be set to 1 if the UE has set bit number 38 to 1."9 Measurement reporting event: Event B1 - Neighbour > threshold for UTRAN FDD, if the UE supports UTRAN FDD and has set bit number 22 to 1 36.331, Annex B.1 Rel-9 yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 41.Set to true if supporting all functionalities in the feature group.Yes for FDD, unless UE has set bit number 15 to 1"10 Undefined 36.331, Annex B.1 Rel-9 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 42.11 Undefined 36.331, Annex B.1 Rel-9 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 43.12 Undefined 36.331, Annex B.1 Rel-9 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 44.13 Undefined 36.331, Annex B.1 Rel-9 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 45.14 Undefined 36.331, Annex B.1 Rel-9 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 46.15 Undefined 36.331, Annex B.1 Rel-9 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 47.16 Undefined 36.331, Annex B.1 Rel-9 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 48.17 Undefined 36.331, Annex B.1 Rel-9 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 49.18 Undefined 36.331, Annex B.1 Rel-9 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 50.19 Undefined 36.331, Annex B.1 Rel-9 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 51.20 Undefined 36.331, Annex B.1 Rel-9 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 52.21 Undefined 36.331, Annex B.1 Rel-9 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 53.22 Undefined 36.331, Annex B.1 Rel-9 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 54.23 Undefined 36.331, Annex B.1 Rel-9 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 55.24 Undefined 36.331, Annex B.1 Rel-9 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 56.25 Undefined 36.331, Annex B.1 Rel-9 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 57.26 Undefined 36.331, Annex B.1 Rel-9 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 58.27 Undefined 36.331, Annex B.1 Rel-9 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 59.28 Undefined 36.331, Annex B.1 Rel-9 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 60.29 Undefined 36.331, Annex B.1 Rel-9 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 61.30 Undefined 36.331, Annex B.1 Rel-9 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 62.31 Undefined 36.331, Annex B.1 Rel-9 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 63.32 Undefined 36.331, Annex B.1 Rel-9 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 64.Table A.4.5-1e Feature group indicators 33-64 for TDD Reference Release Status Supported Allowed Comments1 "Inter-RAT ANR features for UTRAN including:- Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCellsForSON- Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI" 36.331, Annex B.1 Rel-9 yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 33.Set to true if supporting all functionalities in the feature group.- can only be set to 1 if the UE has set bit number 5 and bit number 22 to 1."2 "Inter-RAT ANR features for GERAN including:- Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells- Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI" 36.331, Annex B.1 Rel-9 yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 34.Set to true if supporting all functionalities in the feature group.- can only be set to 1 if the UE has set bit number 5 and bit number 23 to 1."3 "Inter-RAT ANR features for 1xRTT including:- Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCellsForSON- Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI" 36.331, Annex B.1 Rel-9 no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 35.Set to true if supporting all functionalities in the feature group.- can only be set to 1 if the UE has set bit number 5 and bit number 24 to 1."4 "Inter-RAT ANR features for HRPD including:- Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCellsForSON- Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI" 36.331, Annex B.1 Rel-9 no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 36.Set to true if supporting all functionalities in the feature group.- can only be set to 1 if the UE has set bit number 5 and bit number 26 to 1."5 "Inter-RAT ANR features for UTRAN TDD including:- Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCellsForSON- Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI" 36.331, Annex B.1 Rel-9 no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 37.Set to true if supporting all functionalities in the feature group.- can only be set to 1 if the UE has set bit number 5 and at least one of the bit number 22 (for UEs supporting only UTRA TDD) or the bit number 39 to 1."6 - EUTRA RRC_CONNECTED to UTRA TDD CELL_DCH PS handover, if the UE supports both UTRAN FDD and UTRAN TDD 36.331, Annex B.1 Rel-9 no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 38.Set to true if supporting all functionalities in the feature group.- can only be set to 1 if the UE has set bit number 39 to 1."7 - UTRAN TDD measurements, reporting and measurement reporting event B2 in E-UTRA connected mode, if the UE supports both UTRAN FDD and UTRAN TDD 36.331, Annex B.1 Rel-9 no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 39,Set to true if supporting all functionalities in the feature group."8 - EUTRA RRC_CONNECTED to UTRA TDD CELL_DCH CS handover, if the UE supports both UTRAN FDD and UTRAN TDD 36.331, Annex B.1 Rel-9 no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 40.Set to true if supporting all functionalities in the feature group.- related to SR-VCC- can only be set to 1 if the UE has set bit number 38 to 1."9 Measurement reporting event: Event B1 - Neighbour > threshold for UTRAN FDD, if the UE supports UTRAN FDD and has set bit number 22 to 1 36.331, Annex B.1 Rel-9 yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 41.Set to true if supporting all functionalities in the feature group."10 Undefined 36.331, Annex B.1 Rel-9 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 42.11 Undefined 36.331, Annex B.1 Rel-9 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 43.12 Undefined 36.331, Annex B.1 Rel-9 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 44.13 Undefined 36.331, Annex B.1 Rel-9 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 45.14 Undefined 36.331, Annex B.1 Rel-9 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 46.15 Undefined 36.331, Annex B.1 Rel-9 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 47.16 Undefined 36.331, Annex B.1 Rel-9 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 48.17 Undefined 36.331, Annex B.1 Rel-9 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 49.18 Undefined 36.331, Annex B.1 Rel-9 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 50.19 Undefined 36.331, Annex B.1 Rel-9 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 51.20 Undefined 36.331, Annex B.1 Rel-9 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 52.21 Undefined 36.331, Annex B.1 Rel-9 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 53.22 Undefined 36.331, Annex B.1 Rel-9 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 54.23 Undefined 36.331, Annex B.1 Rel-9 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 55.24 Undefined 36.331, Annex B.1 Rel-9 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 56.25 Undefined 36.331, Annex B.1 Rel-9 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 57.26 Undefined 36.331, Annex B.1 Rel-9 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 58.27 Undefined 36.331, Annex B.1 Rel-9 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 59.28 Undefined 36.331, Annex B.1 Rel-9 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 60.29 Undefined 36.331, Annex B.1 Rel-9 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 61.30 Undefined 36.331, Annex B.1 Rel-9 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 62.31 Undefined 36.331, Annex B.1 Rel-9 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 63.32 Undefined 36.331, Annex B.1 Rel-9 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 64.Table A.4.5-2 EUTRA Feature group indicators Reference Release Status Supported Allowed Comments1 "Support of- UTRA CELL_PCH to EUTRA RRC_IDLE cell reselection- UTRA URA_PCH to EUTRA RRC_IDLE cell reselection" 25.331, Annex E Rel-8 yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 1For Rel-8:Set to true if supporting all functionalities in the feature groupFor Rel-9 or later releases:this FGI bit is set to TRUE s"2 "Support of- EUTRAN measurements and reporting in connected mode" 25.331, Annex E Rel-8 yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 2Set to true if supporting all functionalities in the feature group"3 "Support of- UTRA CELL_FACH absolute priority cell reselection for high priority layers" 25.331, Annex E "Rel-8 to Rel-10Rel-11" no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 3Set to true if supporting all functionalities in the feature groupUE supporting E-UTRAN shall set this bit to ‘TRUE’ in this version of specification.UE supporting E-UTRAN shall set this bit to ‘TRUE’ in this version of specification."4 "Support of- UTRA CELL_FACH absolute priority cell reselection for all layers" 25.331, Annex E "Rel-8 to Rel-10Rel-11" no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 4Set to true if supporting all functionalities in the feature groupUE supporting E-UTRAN shall set this bit to ‘TRUE’ in this version of specification.UE supporting E-UTRAN shall set this bit to ‘TRUE’ in this version of specification."Table A.4.5-3 Void Reference Release Status Supported Allowed CommentsTable A.4.5-3a Release 10 AS feature group indicators 101-132 for FDD Reference Release Status Supported Allowed Comments1 - DMRS with OCC (orthogonal cover code) and SGH (sequence group hopping) disabling 36.331, Annex C.1 "Rel-10Rel-12" no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 101.Set to true if supporting all functionalities in the feature group.If UE supports FDD and TDD this item shall be set to same value as for item 1 in Table A.4.5-3b for TDD.- if the UE supports two or more layers for spatial multiplexing in UL, this bit shall be set to 1.(Rel-10)- A Category 0 UE shall set this bit to 0 if it does not support this feature.(Rel-12)"2 " - Trigger type 1 SRS (aperiodic SRS) transmission (Up to X ports)NOTE: X = number of supported layers on given band" 36.331, Annex C.1 Rel-10 no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 102.Set to true if supporting all functionalities in the feature group."3 - PDSCH transmission mode 9 when up to 4 CSI reference signal ports are configured 36.331, Annex C.1 Rel-10 no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 103.Set to true if supporting all functionalities in the feature group.- for Category 8 UEs, this bit shall be set to 1."4 - PDSCH transmission mode 9 for TDD when 8 CSI reference signal ports are configured 36.331, Annex C.1 Rel-10 no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 104.Set to true if supporting all functionalities in the feature group.If UE supports FDD and TDD this item shall be set to same value as for item 4 in Table A.4.5-3b for TDD.- if the UE does not support TDD, this bit is irrelevant (capability signalling exists for FDD for this feature), and this bit shall be set to 0.- for Category 8 UEs, this bit shall be set to 1."5 " - Periodic CQI/PMI/RI reporting on PUCCH: Mode 2-0 – UE selected subband CQI without PMI, when PDSCH transmission mode 9 is configured- Periodic CQI/PMI/RI reporting on PUCCH: Mode 2-1 – UE selected subband CQI with single PMI, when PDSCH transmission mode 9 and up to 4 CSI reference signal ports are configured" 36.331, Annex C.1 "Rel-10Rel-12" no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 105.Set to true if supporting all functionalities in the feature group.Corresponding to the Index of Indicator, the leftmost binary bit 105Set to true if supporting all functionalities in the feature group"6 - Periodic CQI/PMI/RI/PTI reporting on PUCCH: Mode 2-1 – UE selected subband CQI with single PMI, when PDSCH transmission mode 9 and 8 CSI reference signal ports are configured 36.331, Annex C.1 "Rel-10Rel-12" no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 106.Set to true if supporting all functionalities in the feature group.- this bit can be set to 1 only if the UE supports PDSCH transmission mode 9 with 8 CSI reference signal ports (i.e., for TDD, if index 104 is set to 1, and for FDD, if tm9-With-8Tx-FDD-r10 is set to ‘supported’) and if index 2 (Table B.1-1) is set to 1."7 " - Aperiodic CQI/PMI/RI reporting on PUSCH: Mode 2-0 – UE selected subband CQI without PMI, when PDSCH transmission mode 9 is configured- Aperiodic CQI/PMI/RI reporting on PUSCH: Mode 2-2 – UE selected subband CQI with multiple PMI, when PDSCH transmission mode 9 and up to 4 CSI reference signal ports are configured" 36.331, Annex C.1 Rel-10 no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 107.Set to true if supporting all functionalities in the feature group.- this bit can be set to 1 only if indices 1 (Table B.1-1) and 103 are set to 1."8 - Aperiodic CQI/PMI/RI reporting on PUSCH: Mode 2-2 – UE selected subband CQI with multiple PMI, when PDSCH transmission mode 9 and 8 CSI reference signal ports are configured 36.331, Annex C.1 Rel-10 no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 108.Set to true if supporting all functionalities in the feature group.- this bit can be set to 1 only if the UE supports PDSCH transmission mode 9 with 8 CSI reference signal ports (i.e., for TDD, if index 104 is set to 1, and for FDD, if tm9-With-8Tx-FDD-r10 is set to ‘supported’) and if index 1 (Table B.1-1) is set to 1."9 - Periodic CQI/PMI/RI reporting on PUCCH Mode 1-1, submode 1 36.331, Annex C.1 "Rel-10Rel-12" no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 109.Set to true if supporting all functionalities in the feature group.- this bit can be set to 1 only if the UE supports PDSCH transmission mode 9 with 8 CSI reference signal ports (i.e., for TDD, if index 104 is set to 1, and for FDD, if tm9-With-8Tx-FDD-r10 is set to ‘supported’)."10 - Periodic CQI/PMI/RI reporting on PUCCH Mode 1-1, submode 2 36.331, Annex C.1 "Rel-10Rel-12" no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 110.Set to true if supporting all functionalities in the feature group.- this bit can be set to 1 only if the UE supports PDSCH transmission mode 9 with 8 CSI reference signal ports (i.e., for TDD, if index 104 is set to 1, and for FDD, if tm9-With-8Tx-FDD-r10 is set to ‘supported’)."11 - Measurement reporting trigger event A6 36.331, Annex C.1 Rel-10 no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 111.Set to true if supporting all functionalities in the feature group.- this bit can be set to 1 only if the UE supports carrier aggregation."12 - SCell addition within the Handover to EUTRA procedure 36.331, Annex C.1 Rel-10 no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 112.Set to true if supporting all functionalities in the feature group.- this bit can be set to 1 only if the UE supports carrier aggregation and the Handover to EUTRA procedure."13 " - Trigger type 0 SRS (periodic SRS) transmission on X Serving CellsNOTE: X = number of supported component carriers in a given band combination" 36.331, Annex C.1 Rel-10 no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 113.Set to true if supporting all functionalities in the feature group.- this bit can be set to 1 only if the UE supports carrier aggregation in UL."14 - Reporting of both UTRA CPICH RSCP and Ec/N0 in a Measurement Report 36.331, Annex C.1 Rel-10 yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 114.Set to true if supporting all functionalities in the feature group.If UE supports FDD and TDD this item shall be set to same value as for item 14 in Table A.4.5-3b for TDD.- this bit can be set to 1 only if index 22 (Table B.1-1) is set to 1."15 " - time domain ICIC RLM/RRM measurement subframe restriction for the serving cell- time domain ICIC RRM measurement subframe restriction for neighbour cells- time domain ICIC CSI measurement subframe restriction" 36.331, Annex C.1 Rel-10 no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 115.Set to true if supporting all functionalities in the feature group."16 - Relative transmit phase continuity for spatial multiplexing in UL 36.331, Annex C.1 Rel-10 no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 116.Set to true if supporting all functionalities in the feature group.- this bit can be set to 1 only if the UE supports two or more layers for spatial multiplexing in UL."17 Undefined 36.331, Annex C.1 Rel-10 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 117.18 Undefined 36.331, Annex C.1 Rel-10 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 118.19 Undefined 36.331, Annex C.1 Rel-10 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 119.20 Undefined 36.331, Annex C.1 Rel-10 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 120.21 Undefined 36.331, Annex C.1 Rel-10 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 121.22 Undefined 36.331, Annex C.1 Rel-10 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 122.23 Undefined 36.331, Annex C.1 Rel-10 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 123.24 Undefined 36.331, Annex C.1 Rel-10 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 124.25 Undefined 36.331, Annex C.1 Rel-10 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 125.26 Undefined 36.331, Annex C.1 Rel-10 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 126.27 Undefined 36.331, Annex C.1 Rel-10 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 127.28 Undefined 36.331, Annex C.1 Rel-10 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 128.29 Undefined 36.331, Annex C.1 Rel-10 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 129.30 Undefined 36.331, Annex C.1 Rel-10 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 130.31 Undefined 36.331, Annex C.1 Rel-10 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 131.32 Undefined 36.331, Annex C.1 Rel-10 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 132.Table A.4.5-3b Release 10 AS feature group indicators 101-132 for TDD Reference Release Status Supported Allowed Comments1 - DMRS with OCC (orthogonal cover code) and SGH (sequence group hopping) disabling 36.331, Annex C.1 "Rel-10Rel-12" no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 101.Set to true if supporting all functionalities in the feature group.If UE supports FDD and TDD this item shall be set to same value as for item 1 in Table A.4.5-3a for FDD.- if the UE supports two or more layers for spatial multiplexing in UL, this bit shall be set to 1.(Rel-10)- A Category 0 UE shall set this bit to 0 if it does not support this feature.(Rel-12)"2 " - Trigger type 1 SRS (aperiodic SRS) transmission (Up to X ports)NOTE: X = number of supported layers on given band" 36.331, Annex C.1 Rel-10 no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 102.Set to true if supporting all functionalities in the feature group."3 - PDSCH transmission mode 9 when up to 4 CSI reference signal ports are configured 36.331, Annex C.1 Rel-10 no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 103.Set to true if supporting all functionalities in the feature group.- for Category 8 UEs, this bit shall be set to 1."4 - PDSCH transmission mode 9 for TDD when 8 CSI reference signal ports are configured 36.331, Annex C.1 Rel-10 no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 104.Set to true if supporting all functionalities in the feature group.If UE supports FDD and TDD this item shall be set to same value as for item 4 in Table A.4.5-3a for FDD.- if the UE does not support TDD, this bit is irrelevant (capability signalling exists for FDD for this feature), and this bit shall be set to 0.- for Category 8 UEs, this bit shall be set to 1."5 " - Periodic CQI/PMI/RI reporting on PUCCH: Mode 2-0 – UE selected subband CQI without PMI, when PDSCH transmission mode 9 is configured- Periodic CQI/PMI/RI reporting on PUCCH: Mode 2-1 – UE selected subband CQI with single PMI, when PDSCH transmission mode 9 and up to 4 CSI reference signal ports are configured" 36.331, Annex C.1 "Rel-10Rel-12" no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 105.Set to true if supporting all functionalities in the feature group.Corresponding to the Index of Indicator, the leftmost binary bit 105Set to true if supporting all functionalities in the feature group"6 - Periodic CQI/PMI/RI/PTI reporting on PUCCH: Mode 2-1 – UE selected subband CQI with single PMI, when PDSCH transmission mode 9 and 8 CSI reference signal ports are configured 36.331, Annex C.1 "Rel-10Rel-12" no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 106.Set to true if supporting all functionalities in the feature group.- this bit can be set to 1 only if the UE supports PDSCH transmission mode 9 with 8 CSI reference signal ports (i.e., for TDD, if index 104 is set to 1, and for FDD, if tm9-With-8Tx-FDD-r10 is set to ‘supported’) and if index 2 (Table B.1-1) is set to 1."7 " - Aperiodic CQI/PMI/RI reporting on PUSCH: Mode 2-0 – UE selected subband CQI without PMI, when PDSCH transmission mode 9 is configured- Aperiodic CQI/PMI/RI reporting on PUSCH: Mode 2-2 – UE selected subband CQI with multiple PMI, when PDSCH transmission mode 9 and up to 4 CSI reference signal ports are configured" 36.331, Annex C.1 Rel-10 no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 107.Set to true if supporting all functionalities in the feature group.- this bit can be set to 1 only if indices 1 (Table B.1-1) and 103 are set to 1."8 - Aperiodic CQI/PMI/RI reporting on PUSCH: Mode 2-2 – UE selected subband CQI with multiple PMI, when PDSCH transmission mode 9 and 8 CSI reference signal ports are configured 36.331, Annex C.1 Rel-10 no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 108.Set to true if supporting all functionalities in the feature group.- this bit can be set to 1 only if the UE supports PDSCH transmission mode 9 with 8 CSI reference signal ports (i.e., for TDD, if index 104 is set to 1, and for FDD, if tm9-With-8Tx-FDD-r10 is set to ‘supported’) and if index 1 (Table B.1-1) is set to 1."9 - Periodic CQI/PMI/RI reporting on PUCCH Mode 1-1, submode 1 36.331, Annex C.1 "Rel-10Rel-12" no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 109.Set to true if supporting all functionalities in the feature group.- this bit can be set to 1 only if the UE supports PDSCH transmission mode 9 with 8 CSI reference signal ports (i.e., for TDD, if index 104 is set to 1, and for FDD, if tm9-With-8Tx-FDD-r10 is set to ‘supported’)."10 - Periodic CQI/PMI/RI reporting on PUCCH Mode 1-1, submode 2 36.331, Annex C.1 "Rel-10Rel-12" no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 110.Set to true if supporting all functionalities in the feature group.- this bit can be set to 1 only if the UE supports PDSCH transmission mode 9 with 8 CSI reference signal ports (i.e., for TDD, if index 104 is set to 1, and for FDD, if tm9-With-8Tx-FDD-r10 is set to ‘supported’)."11 - Measurement reporting trigger event A6 36.331, Annex C.1 Rel-10 no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 111.Set to true if supporting all functionalities in the feature group.- this bit can be set to 1 only if the UE supports carrier aggregation."12 - SCell addition within the Handover to EUTRA procedure 36.331, Annex C.1 Rel-10 no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 112.Set to true if supporting all functionalities in the feature group.- this bit can be set to 1 only if the UE supports carrier aggregation and the Handover to EUTRA procedure."13 " - Trigger type 0 SRS (periodic SRS) transmission on X Serving CellsNOTE: X = number of supported component carriers in a given band combination" 36.331, Annex C.1 Rel-10 no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 113.Set to true if supporting all functionalities in the feature group.- this bit can be set to 1 only if the UE supports carrier aggregation in UL."14 - Reporting of both UTRA CPICH RSCP and Ec/N0 in a Measurement Report 36.331, Annex C.1 Rel-10 yes yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 114.Set to true if supporting all functionalities in the feature group.If UE supports FDD and TDD this item shall be set to same value as for item 14 in Table A.4.5-3a for FDD.- this bit can be set to 1 only if index 22 (Table B.1-1) is set to 1."15 " - time domain ICIC RLM/RRM measurement subframe restriction for the serving cell- time domain ICIC RRM measurement subframe restriction for neighbour cells- time domain ICIC CSI measurement subframe restriction" 36.331, Annex C.1 Rel-10 no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 115.Set to true if supporting all functionalities in the feature group."16 - Relative transmit phase continuity for spatial multiplexing in UL 36.331, Annex C.1 Rel-10 no yes, no "Corresponding to the Index of Indicator, the leftmost binary bit 116.Set to true if supporting all functionalities in the feature group.- this bit can be set to 1 only if the UE supports two or more layers for spatial multiplexing in UL."17 Undefined 36.331, Annex C.1 Rel-10 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 117.18 Undefined 36.331, Annex C.1 Rel-10 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 118.19 Undefined 36.331, Annex C.1 Rel-10 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 119.20 Undefined 36.331, Annex C.1 Rel-10 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 120.21 Undefined 36.331, Annex C.1 Rel-10 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 121.22 Undefined 36.331, Annex C.1 Rel-10 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 122.23 Undefined 36.331, Annex C.1 Rel-10 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 123.24 Undefined 36.331, Annex C.1 Rel-10 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 124.25 Undefined 36.331, Annex C.1 Rel-10 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 125.26 Undefined 36.331, Annex C.1 Rel-10 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 126.27 Undefined 36.331, Annex C.1 Rel-10 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 127.28 Undefined 36.331, Annex C.1 Rel-10 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 128.29 Undefined 36.331, Annex C.1 Rel-10 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 129.30 Undefined 36.331, Annex C.1 Rel-10 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 130.31 Undefined 36.331, Annex C.1 Rel-10 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 131.32 Undefined 36.331, Annex C.1 Rel-10 no yes, no Corresponding to the Index of Indicator, the leftmost binary bit 132.Test Spec 3GPP TR 37.901 V11.13.0 Table D.3.3.1-1 UE Radio Technologies Reference Release Status Supported Allowed Comments1 E-UTRA FDD 36.101 Rel-8 yes yes, no pc_eFDD2 E-UTRA TDD 36.101 Rel-8 yes yes, no pc_eTDD3 UTRA FDD 25.101 Rel-5 yes yes, no pc_FDD4 UTRA TDD 25.102 Rel-7 no yes, no pc_TDDTable D.3.3.1-2 Internet Protocol Technologies Reference Release Status Supported Allowed Comments1 FTP RFC 959 n/a yes yes, no 2 UDP RFC 768 n/a yes yes, no Table D.3.3.3-1 PUSCH physical layer Categories Reference Release Status Supported Allowed Comments1 Category 1 36.306, 4.1 Rel-8 no yes, no 2 Category 2 36.306, 4.1 Rel-8 no yes, no 3 Category 3 36.306, 4.1 Rel-8 no yes, no 4 Category 4 36.306, 4.1 Rel-8 yes yes, no 5 Category 5 36.306, 4.1 Rel-8 no yes, no Support for 64QAM in ULTable D.3.3.3-2 PDSCH physical layer Categories Reference Release Status Supported Allowed Comments1 Category 1 36.306, 4.1 Rel-8 no yes, no 2 Category 2 36.306, 4.1 Rel-8 no yes, no 3 Category 3 36.306, 4.1 Rel-8 no yes, no 4 Category 4 36.306, 4.1 Rel-8 yes yes, no 5 Category 5 36.306, 4.1 Rel-8 no yes, no Table D.3.4.1-1 UE data configuration capabilities types Reference Release Status Supported Allowed Comments1 Tethered Data C.2.1 n/a yes yes, no 2 Embedded data C.2.2 n/a no yes, no 0 0
- LTE Protocol PICS
- LTE RF PICS
- WCDMA protocol PICS
- pics
- GSM pics
- SIM PICS
- MMS PICS
- vedio PICS
- LTE Radio Protocol Architecture(UP和CP的区别)
- LTE
- LTE
- LTE
- LTE
- LTE
- LTE
- LTE
- LTE
- 330pics-shell scripts_third
- 过滤器、拦截器、监听器总结
- 算法之红黑树简单理解和定义
- 怎样玩无屏幕树莓派
- 《javascript设计模式与开发实践》阅读笔记（一）
- Android_PopUpWindow_相机-相册
- LTE Protocol PICS
- android layout_gravity失效的问题
- 机器学习、深度学习的理论与实战入门建议整理（一）
- java中this关键字的使用
- 简单点，搭博客的方式简单点——开源博客Typecho
- [kernel 启动流程] （第六章）第一阶段之——打开MMU
- 5 java se(5)----IO流
- 中国剩余定理
- 数据库默认值修改
