高通开发笔记---yukon worknote
来源：互联网 发布：中国现代汉语词典软件 编辑：程序博客网 时间：2024/06/03 21:46
点击打开链接
daily build
http://android-ci-platform.cnbj.sonyericsson.net/job/daily_build_jb-mr2-yukon/
DL-CNBJ-TianChi-SWCM: tianchi gina jb 的 CM
一. msm8226-tianchi_dsds.dtsi; msm-pm8226.dtsi
二、. Audio Jack
NC 和 NO的选择改成了dts里面设置
@kernel/arch/arm/boot/dts/Msm8226-tianchi_dsds.dtsi
&soc {
sound {
qcom,headset-jack-type-NO; ---> qcom,headset-jack-type-NC 后来改成这个了 ！！！！！！！
}
}
msm8226_asoc_machine_probe@kernel/sound/soc/msm/Msm8226.c
mbhc_cfg.gpio_level_insert = of_property_read_bool(pdev->dev.of_node,"qcom,headset-jack-type-NO");
//该处设置是否NC和NO
http://review.sonyericsson.net/#/c/560971/
micbias 设置 @kernel/arch/arm/boot/dts/msm8226.dtsi
tapan_codec {
qcom,cdc-micbias-cfilt1-mv = <1800>;
qcom,cdc-micbias-cfilt2-mv = <2700>;
qcom,cdc-micbias-cfilt3-mv = <1800>;
}
识别耳机类型出错，需要 mbhc_cfg.cs_enable_flags = 0 @kernel/sound/soc/msm/msm8226.c
三. Vibrator
@kernel/arch/arm/boot/dts/msm8226-tianchi_dsds.dtsi
qcom,vibrator@c000 {
status = "okay";
compatible = "qcom,qpnp-vibrator";
reg = <0xc000 0x100>;
label = "vibrator";
qcom,vib-timeout-ms = <15000>;
qcom,vib-vtg-level-mV = <3100>;
};
然后可以工作了
源代码@kernel/drivers/platform/msm/qpnp-vibrator.c
检查是否工作 #echo 1000 > /sys/class/timed_output/vibrator/enable
四、如何查看qcom release for VI
1. CM关于该项目的wiki: https://wiki.sonyericsson.net/androiki/PLD_CM/yukon
->Vendor integration -->Yukon VI History
查看 Current Deliveries -> VI Info,选择相应版本进入
->QC subsystem components
->Opensource (LINUX) 该项为kernel版本 LNX.LA.3.2-01520-8x26.0
2. 高通的kernel代码 https://www.codeaurora.org/cgit/quic/la//kernel/msm/
->Tag 中找到对应的版本号 比如：LNX.LA.3.2.1-01520-8x26.0
->进入后选择 上边的 tree 页签 可以找到具体的文件，比如 driver/power/qpnp-charger.c
->如果想看修改记录，则在进入具体文件前，也就是文件列表中，选择文件后面的log 打开浏览
五、Charge only
1. 插PC USB不能进入charge only mode
misc ta 2002 01-->00
六、tsubasa audio jack porting for jb-blue-mr2
1. kernel/input/misc/simple_remote.c
static int simple_remote_probe(struct platform_device *pdev)
{
/* device name */ 用于耳机检测 上报uevent事件给framewore
jack->swdev.name = "h2w";
/* print function name */
jack->swdev.print_name = simple_remote_print_name;
ret = switch_dev_register(&jack->swdev);
/* Create input device for normal key events. */
jack->indev = input_allocate_device();
...
ret = input_register_device(jack->indev);
/* Create input device for application key events. */
jack->indev_appkey = input_allocate_device();
...
ret = input_register_device(jack->indev_appkey);
}
static void simple_remote_report_accessory_type
{
...
switch_set_state(&jack->swdev, jack->new_accessory_state); //当耳机插入或拔出时，发送switch uevent 到framework
}
2. 检测 耳机插入switch uevent
/sys/class/switch/h2w/state 0:没有耳机; 1:headset; 2:headphone;
3. 相关的gerrit
http://review.sonyericsson.net/#/c/565711
http://review.sonyericsson.net/#/c/470796
七、BMS 设置参数的说明
1. @qpnp-adc-voltage.c 中注册各个channel sysfs
在该qpnp_vadc_init_hwmon函数中会读取所有的pm8226_vadc的child node,然后逐个device_create_file， 这样在手机/sys/devices/qpnp-vadc-e4b43000路径下就注册了与 pm8226_vadc@kernel/arch/arm/boot/dts/msm-pm8226.dtsi和pm8226_vadc@kernel/arch/arm/boot/dts/msm8226.dtsi中 所有channel(child node) 一致的sys fs;
比如 die-temp
pm8226_vadc: vadc@3100 {
chan@8 {
label = "die_temp";
reg = <8>;
qcom,decimation = <0>;
qcom,pre-div-channel-scaling = <0>;
qcom,calibration-type = "absolute";
qcom,scale-function = <3>;
qcom,hw-settle-time = <0>;
qcom,fast-avg-setup = <0>;
};
｝
2. tm-temp-margin : 如果新的die-temp温度超过预先设置 的[上一次die-temp - tm-temp-margin, 上一次die-temp + tm-temp-margin] 则会触发
btm_notify_die_temp@qpnp-bms.c
->schedule_work(&chip->recalc_work); //重新计算soc,这时候因为温度有变化，所以计算的值与上次就不一样了，实际上是温度变化超过了一定范围，需要重新校准soc的计算；
->refresh_die_temp_monitor(chip); //再次用最新的die-temp重新设置trigger范围。
3. low-ocv-correction-limit-uv和high-ocv-correction-limit-uv和hold-soc-est 主要用于adjust_soc中new_soc的调整出错而限制一个合理的调整范围。
主要用于调整soc @adjust_soc, 由于有温度的影响，所以需要调整，重新获取电池的电压和电流，计算出soc_est, 再根据soc和soc_est计算出delta_ocv_uv, 也就是ocv的微小变化， 这个delta_ocv_uv变化范围应该在［low-ocv-correction-limit-uv，high-ocv-correction-limit-uv］，随后调整last_ocv_uv，基于新的ocv计算新的soc;
如果根据电池电压，电流和温度，计算出来的soc_est >= hold-soc-est, 则尽管根据新的ocv计算出来soc_new=0, 也认为计算有些误差，则强制改变为1，因为毕竟还有少许电池电量
4. enable-fcc-learning-soc
主要是用于生成chip->adjusted_fcc_temp_lut@readjust_fcc_table, 如果再fcc时，则会用新的调整过的adjusted_fcc_temp_lut做插值计算
电池最初的设置fcc_temp_lut，如下
static struct single_row_lut fcc_temp = {
.x = {-20, 0, 25, 40, 65},
.y = {2300, 2318, 2347, 2390, 2400},
.cols = 5,
};
adjusted_fcc_temp_lut是根据新的电池chip->fcc_new_batt_temp和chip->fcc_new_mah来调整不同温度下的fcc
什么时候触发readjust_fcc_table？ 在fcc_learning_config中计算的new_fcc_uah和fcc_uah 相差比较大时（is_new_fcc_valid）则触发
八、检测AICL功能
qpnp_chg_aicl_work
九、miscTA 2227, 55->50
十、耳机检测
echo -n "file wcd9xxx-mbhc.c +p" > /sys/kernel/debug/dynamic_debug/control
1. wcd9xxx_cs_find_plug_type@wcd9xxx-mbhc.c,中门限电压的设置，
#define WCD9XXX_V_CS_HS_MAX 700
#define WCD9XXX_V_CS_NO_MIC 5
def_tapan_mbhc_cal@msm8226.c
S(v_no_mic, 30);
S(v_hs_max, 2450);
hs_max：
no_mic：
wcd9xxx_codec_cs_get_plug_type@wcd9xxx-mbhc.c设置是否用mic_bias, 和检测电压门限
0 false WCD9XXX_V_CS_NO_MIC WCD9XXX_V_CS_HS_MAX
1 false WCD9XXX_V_CS_NO_MIC WCD9XXX_V_CS_HS_MAX
2 false WCD9XXX_V_CS_NO_MIC WCD9XXX_V_CS_HS_MAX
3 false WCD9XXX_V_CS_NO_MIC WCD9XXX_V_CS_HS_MAX
2. Audio button 电压设置区间 def_tapan_mbhc_cal@msm8226.c, 一共8个buttons
btn_cfg = WCD9XXX_MBHC_CAL_BTN_DET_PTR(tapan_cal);
btn_low = wcd9xxx_mbhc_cal_btn_det_mp(btn_cfg, MBHC_BTN_DET_V_BTN_LOW);
btn_high = wcd9xxx_mbhc_cal_btn_det_mp(btn_cfg, MBHC_BTN_D_V_BTN_HIGH);
btn_low[0] = -50;
btn_high[0] = 10;
btn_low[1] = 11;
btn_high[1] = 52;
btn_low[2] = 53;
btn_high[2] = 94;
btn_low[3] = 95;
btn_high[3] = 133;
btn_low[4] = 134;
btn_high[4] = 171;
btn_low[5] = 172;
btn_high[5] = 208;
btn_low[6] = 209;
btn_high[6] = 244;
btn_low[7] = 245;
btn_high[7] = 330;
@kernel/include/linux/input.h 中定义了上报key的键值
初始化 audio button对应的键值 wcd9xxx_mbhc_init@wcd9xxx-mbhc.c
ret = snd_jack_set_key(mbhc->button_jack.jack,
SND_JACK_BTN_0,
KEY_MEDIA);
Huashan对应上报的键值
接听键 --> BTN_MISC/BTN_0 0x100
音量上键 --> BTN_1 0x101
音量下键 --> BTN_2 0x102
smart键 --> BTN_3 0x103
3. wcd9xxx_determine_button@wcd9xxx-mbhc.c 根据电压确认按下的是那个键
wcd9xxx_dce_handler 是audio button 按键处理的中断回调函数
4. wcd9xxx_release_handler@wcd9xxx-mbhc.c
vbatdet irq storm
http://review.sonyericsson.net/#/c/511317
http://review.sonyericsson.net/#/c/511314
*************************************************************************************
Sim card detect
/jb-viskan/kernel/arch/arm/mach-msm/board-sony_viskan_huashan-pmic.c
struct gpio_event_platform_data pmic_keypad_data = {
.name = "sim-detection",
.info = pmic_keypad_info,
.info_count = ARRAY_SIZE(pmic_keypad_info),
};
十一、如何添加msm_thermal
1. 需要和硬件确认用的是那个 vadc channel,用于配置@msm8226-tianchi_dsds.dtsi
&pm8226_vadc {
chan@16 { //0x16 = MPP 7 + 15 = 22, 可参考80-ND928-26_C 文档的 50 page
label = "msm_therm";
reg = <0x16>;
qcom,decimation = <0>;
qcom,pre-div-channel-scaling = <0>;
qcom,calibration-type = "ratiometric";
qcom,scale-function = <2>;
//用的是static struct qpnp_vadc_scale_fn vadc_scale_fn[]中的[SCALE_THERM_100K_PULLUP] = {qpnp_adc_scale_therm_pu2},
// SCALE_THERM_100K_PULLUP = 2
qcom,hw-settle-time = <2>;
qcom,fast-avg-setup = <0>;
};
}
由MPP计算channel的偏移15的来源，enum qpnp_vadc_channels@kernel/include/linux/qpnp/qpnp-adc.h 在P_MUX1_1_1前正好偏移15
2. 需要和硬件确认用的是那个MPP, 这个从电路图上可以确认msm_thermal 用的是 MMP 7
&pm8226_mpps {
mpp@a600 { /* MPP 7 */
/* MSM_THERM config */
qcom,mode = <4>; /* AIN input */
qcom,invert = <1>; /* Enable MPP */
qcom,ain-route = <2>; /* AMUX 7 */
qcom,master-en = <1>;
qcom,src-sel = <0>; /* Function constant */
};
｝
3. 详细分析pa_therm0 的设计流程
a. 查看电路图 pa_therm用的是MPP_5, 所以@msm8226-tianchi_dsds.dtsi设置
&pm8226_mpps {
mpp@a400 { /* MPP 5 */
/* PA_THERM0 config */
qcom,mode = <4>; /* AIN input */
qcom,invert = <1>; /* Enable MPP */
qcom,ain-route = <0>; /* AMUX 5 */
qcom,master-en = <1>;
qcom,src-sel = <0>; /* Function constant */
};
}
b. 如何配置pm8226_vadc的channel,计算是那个channel; MPP 5 + 15 = 20 = 0x14, 所以@msm8226-tianchi_dsds.dtsi设置
&pm8226_vadc {
chan@14 {
label = "pa_therm0";
reg = <0x14>;
qcom,decimation = <0>;
qcom,pre-div-channel-scaling = <0>;
qcom,calibration-type = "ratiometric";
qcom,scale-function = <2>;
qcom,hw-settle-time = <2>;
qcom,fast-avg-setup = <0>;
};
}
十二、增加audio jack 的button的映射关系
1. @device/somc/yukon/AndroidBoard.mk中添加
include $(CLEAR_VARS)
LOCAL_MODULE := msm8226-tapan-snd-card_Button_Jack.kl
LOCAL_MODULE_TAGS := optional
LOCAL_MODULE_CLASS := ETC
LOCAL_SRC_FILES := $(LOCAL_MODULE)
LOCAL_MODULE_PATH := $(TARGET_OUT_KEYLAYOUT)
include $(BUILD_PREBUILT)
则会在手机 system/usr/keylayout 目录下增加文件 msm8226-tapan-snd-card_Button_Jack.kl
2. @device/somc/yukon/platform.mk中增加
PRODUCT_PACKAGES += \
msm8226-tapan-snd-card_Button_Jack.kl
3. @device/somc/yukon目录下增加文件msm8226-tapan-snd-card_Button_Jack.kl
4. 特别注意 msm8226-tapan-snd-card_Button_Jack.kl的文件名不是随意写的。
status_t KeyMap::load@frameworks/base/libs/androidfw/keyboard.cpp
{
if (deviceConfiguration) {
String8 keyLayoutName;
if (deviceConfiguration->tryGetProperty(String8("keyboard.layout"),
....
}
// Try searching by device identifier.
if (probeKeyMap(deviceIdenfifier, String8::empty())) {
return OK;
}
// Fall back on the Generic key map.
// TODO Apply some additional heuristics here to figure out what kind of
// generic key map to use (US English, etc.) for typical external keyboards.
if (probeKeyMap(deviceIdenfifier, String8("Generic"))) {
return OK;
}
// Try the Virtual key map as a last resort.
if (probeKeyMap(deviceIdenfifier, String8("Virtual"))) {
return OK;
}
}
#getevent -i
add device 2: /dev/input/event7
bus: 0000
vendor 0000
product 0000
version 0000
name: "msm8226-tapan-snd-card Button Jack"
location: "ALSA"
id: ""
version: 1.0.1
events:
KEY (0001): 00e2 0101 0102 0103 0104 0105 0106 0107
input props:
<none>
读取*.kl的名字组合顺序为
a. 首先查看 props中是否有keyboard.layout的参数，如果有则读取该名字的kl文件
b. 如果 该设备的vendor,product和version都不全为0，则通过它们的组合成 kl的文件名
Vendor_%04x_Product_%04x_Version_%04x.kl
Vendor_%04x_Product_%04x.kl
最终形成文件路径system/usr/keylayout/Vendor_xxxx_Product_xxxx.kl或system/usr/keylayout/Vendor_xxxx_Product_xxxx_Version_xxxx.kl
c. 如果vendor,product,version都为0，则通过该设备的name： "msm8226-tapan-snd-card Button Jack"来组合kl文件名
appendInputDeviceConfigurationFileRelativePath中会把其中的空格转换成'_'
最终形成文件路径system/usr/keylayout/msm8226-tapan-snd-card_Button_Jack.kl
5.还可以直接用 snd_jack_set_key 映射
ret = snd_jack_set_key(button_jack.jack,SND_JACK_BTN_0,KEY_MEDIA);
十三、GPIO 4 控制 external OVP FET
1. gpio_set_value 或 gpio_set_value_cansleep
2. gpio_direction_output
if (gpio_is_valid(ext_spk_amp_gpio))
gpio_get_value_cansleep
3. 最新GPIO的设置 http://review.sonyericsson.net/#/c/616064
4. 检测gpio状态 cat sys/kernel/debug/gpio
十四、thermal 的路径
1. msm_therm, pa_therm0, pa_therm1, batt_therm, xo_therm_pu2 位于/sys/devices/qpnp-vadc-e4943c00
2. tsens_tz_sensor0/1/2/3/4/5 位于 /sys/class/thermal/thermal_zone0/1/2/3/4/5
十五、audio jack 中判断 HW_ID 和 RF_ID
static bool msm8226_change_audiojack_type_to_nc(void)
{
int hw_id[3], rf_id[3];
hw_id[0] = gpio_get_value_cansleep(109);
hw_id[1] = gpio_get_value_cansleep(2);
hw_id[2] = gpio_get_value_cansleep(3);
rf_id[0] = gpio_get_value_cansleep(50);
rf_id[1] = gpio_get_value_cansleep(51);
rf_id[2] = gpio_get_value_cansleep(52);
pr_info("%s: hw_id: %d %d %d\n", __func__, hw_id[0], hw_id[1], hw_id[2]);
if( hw_id[0] == 1 && hw_id[1] == 1 && hw_id[2] == 0 ) {
return true;
}
return false;
}
十六、safey timer of charger
1.
&pm8226_chg {
qcom,tchg-mins = <4>; //4min -- 512min
}
2. Set safety timer to minimum value (4 minutes)
$ adb shell
$ cd /sys/kernel/debug/spmi/spmi-0/
$ echo 0x1061 > address
$ echo 0 > data
Attach charger to start charging.
Wait for 4 minutes
十七、几个关键电压
1. 3.2V关机电压,kernel 设置
2. 3.3v 没有充电时的开机电压, 3.42v 充电时的开机电压
十八、msm_therm 精度不够
1. msm_therm 用的vadc_scale_fn是 [SCALE_THERM_100K_PULLUP] = {qpnp_adc_scale_therm_pu2},
adcmap_100k_104ef_104fb 是温度和电压的对应关系
2. @vendor/semc/hardware/device/yukon/sysmon/Android.mk
143 # msm_therm
144 ifeq ($(SEMC_CFG_SYSMON_SENSOR_PM8X26_MSM_THERM),yes)
145 include $(CLEAR_VARS)
146 LOCAL_CFLAGS := -DTZ_USE_NORMAL_UNIT //不需要再定义TZ_USE_NORMAL_UNIT
147 LOCAL_CFLAGS += -DPM8X26_SENSOR_NAME=\"msm_therm\"
148 LOCAL_SRC_FILES := pm8X26_sensor.c tz_function.c
149 LOCAL_MODULE := sysmon_msm_therm
150 include $(LOCAL_PATH)/main.mk
151 endif
3. 精度在sensor_work@vendor/semc/hardware/device/yukon/sysmon/pm8X26_sensor.c 分析
4. pa_therm1和pa_therm0的 LOCAL_CFLAGS := -DTZ_USE_NORMAL_UNIT 也需要去掉，因为用的是msm_therm同一套数据
十九、msm_therm 会调整cpu frequency?
1. @kernel/drivers/thermal/Kconfig
76 config THERMAL_MONITOR
77 bool "Monitor thermal state and limit CPU Frequency"
2. @kernel/arch/arm/configs/yukon_tianchi_defconfig
325 CONFIG_THERMAL_MONITOR=y
3. @kernel/drivers/thermal/msm_thermal.c
module_param_cb(enabled, &module_ops, &enabled, 0644);
4. @kernel/arch/arm/boot/dts/msm8226.dtsi
qcom,msm-thermal
5. @vendor/semc/hardware/device/yukon/sysmon/Android.mk中需要生成sysmon_msm_thermal_disable
msm_thermal_disable.c
@vendor/semc/hardware/device/yukon/sysmon_cfg.mk中添加
SEMC_CFG_SYSMON_MITIGATION_MSM_THERMAL_DISABLE ＝ yes
6. http://review.sonyericsson.net/#/c/590035/
二十、
手动设置电池容量
echo 50 > sys/modules/qpnp_bms/parameters/bms_fake_battery
regulator_set_optimum_mode
usbin_valid: /sys/devices/qpnp-charger-e4942e00/usbin_valid
vbat_sns: /sys/devices/qpnp-vadc-e4943c00/vbat_sns
xo_therm_pu2: /sys/devices/qpnp-vadc-e4943c00/xo_therm_pu2
msm_thermal:
batt_therm:
while true; do ls -l; sleep 10; done;
adb shell am start -n com.semc.sensorlogger/com.semc.sensorlogger.SensorLoggerActivity
1. echo -n "file qpnp-charger.c +p" > /sys/kernel/debug/dynamic_debug/control
echo -n "file wcd9xxx-mbhc.c +p" > /sys/kernel/debug/dynamic_debug/control
adb logcat -s sysmon-msm_therm system_monitor
adb logcat | grep -E "sysmon|system_monitor"
msm_thermal: Limitling cpu0 max frequency to 1305600
- 高通开发笔记---yukon worknote
- 高通开发笔记---Yangtze worknote
- yukon worknote
- 高通开发笔记
- Yangtze worknote
- Huashan worknote
- android 4.4 高通平台开发笔记
- MIB Lotus worknote
- Worknote-xin(blue platform)
- Worknote-kumquat-DD
- Yukon中的数据类型
- 高通 LCD 笔记
- 高通闪光灯笔记
- 高通DSP开发
- Android开发笔记----嵌入高德地图
- Android开发笔记----高德地图定位
- JS-高德地图开发笔记
- 『笔记』高通Vuforia 通过unity实现Android AR开发笔记
- 高通开发笔记---Yangtze worknote
- select2如何清除选择项
- C# Winform对文件夹的权限判断及处理
- 上海培训纪要
- kernel-host_test
- 高通开发笔记---yukon worknote
- SQL常用系统表
- java生成 图片验证码
- Linux Ubuntu PPTP方式连接VPN图文教程
- nmake环境变量配置
- firefox firegestures 关闭 图片 显示 脚本
- Java之this的用法
- 现场操作前,软件界面的各个功能面板应该通过拖动进行合理布局.请看参考图
- 电脑键盘工作原理
