使用sina33的SDK点亮SC3817R上面的rtl8188eu（分色排版）

来源：互联网发布：组策略限制软件运行编辑：程序博客网时间：2024/05/29 13:13

使用sina33的SDK点亮SC3817R上面的rtl8188eu

大文实验室/大文哥

壹捌陆捌零陆捌捌陆捌贰

wb4916 AT qq.com

完成时间：2017/6/19 10:52

版本：V1.0

1、

W:\a33\rtl8188eu_sc3817r_sina33\android\device\softwinner\astar-y3\overlay\frameworks\base\core\res\res\values\config.xml

（干掉BT部分）

<!-- List of regexpressions describing the interface (if any) that represent tetherable

bluetooth interfaces. If the device doesn't want to support tethering over bluetooth this

should be empty. -->

<string-array translatable="false" name="config_tether_bluetooth_regexs">

</string-array>

2、

W:\a33\rtl8188eu_sc3817r_sina33\android\device\softwinner\astar-y3\astar_y3.mk

（干掉BT部分）

# wifi features

PRODUCT_COPY_FILES += \

frameworks/native/data/etc/android.hardware.wifi.xml:system/etc/permissions/android.hardware.wifi.xml \

frameworks/native/data/etc/android.hardware.wifi.direct.xml:system/etc/permissions/android.hardware.wifi.direct.xml

#frameworks/native/data/etc/android.hardware.bluetooth.xml:system/etc/permissions/android.hardware.bluetooth.xml \

#frameworks/native/data/etc/android.hardware.bluetooth_le.xml:system/etc/permissions/android.hardware.bluetooth_le.xml

关闭BT+GMS+3G数据卡==：

#rtl8723bs bt fw and config

#$(call inherit-product, hardware/realtek/bluetooth/rtl8723bs/firmware/rtlbtfw_cfg.mk)

# camera config for camera detector

#PRODUCT_COPY_FILES += \

#device/softwinner/astar-y3/hawkview/sensor_list_cfg.ini:system/etc/hawkview/sensor_list_cfg.ini

#add gms features

#PRODUCT_COPY_FILES += \

# frameworks/native/data/etc/android.hardware.faketouch.xml:system/etc/permissions/android.hardware.faketouch.xml \

# frameworks/native/data/etc/android.hardware.touchscreen.multitouch.jazzhand.xml:system/etc/permissions/android.hardware.touchscreen.multitouch.jazzhand.xml \

# frameworks/native/data/etc/android.hardware.usb.host.xml:system/etc/permissions/android.hardware.usb.host.xml

# 3G Data Card Packages

#PRODUCT_PACKAGES += \

#u3gmonitor \

#chat \

#rild \

#pppd

# 3G Data Card Configuration Flie

#PRODUCT_COPY_FILES += \

#device/softwinner/polaris-common/rild/ip-down:system/etc/ppp/ip-down \

#device/softwinner/polaris-common/rild/ip-up:system/etc/ppp/ip-up \

#device/softwinner/polaris-common/rild/3g_dongle.cfg:system/etc/3g_dongle.cfg \

#device/softwinner/polaris-common/rild/usb_modeswitch:system/bin/usb_modeswitch \

#device/softwinner/polaris-common/rild/call-pppd:system/xbin/call-pppd \

#device/softwinner/polaris-common/rild/usb_modeswitch.sh:system/xbin/usb_modeswitch.sh \

#device/softwinner/polaris-common/rild/apns-conf_sdk.xml:system/etc/apns-conf.xml \

#device/softwinner/polaris-common/rild/libsoftwinner-ril.so:system/lib/libsoftwinner-ril.so

#PRODUCT_COPY_FILES += \

#device/softwinner/polaris-common/rild/init.3gdongle.rc:root/init.sunxi.3gdongle.rc

# 3G Data Card usb modeswitch File

#PRODUCT_COPY_FILES += \

#$(call find-copy-subdir-files,*,device/softwinner/polaris-common/rild/usb_modeswitch.d,system/etc/usb_modeswitch.d)

#PRODUCT_PACKAGES += Bluetooth

#PRODUCT_PROPERTY_OVERRIDES += \

#ro.product.8723b_bt.used=true

支持adb shell

PRODUCT_PROPERTY_OVERRIDES += \

persist.sys.usb.config=mass_storage,adb \

ro.adb.secure=0

ro.udisk.lable=Polaris \

ro.font.scale=1.0 \

ro.hwa.force=false \

rw.logger=0 \

ro.sys.bootfast=true \

debug.hwc.showfps=0 \

debug.hwui.render_dirty_regions=false

#ro.sys.storage_type = emulated \

#for gms

#PRODUCT_PROPERTY_OVERRIDES += \

# ro.sys.mutedrm=true \

# ro.adb.secure=1

1280x800的分辨率需要修改这里：213

PRODUCT_PROPERTY_OVERRIDES += \

ro.sf.lcd_density=213 \

ro.product.firmware=v2.0

关闭GMS：

#include device/softwinner/polaris-common/prebuild/google/products/gms_base.mk

3、

W:\a33\rtl8188eu_sc3817r_sina33\android\device\softwinner\astar-y3\BoardConfig.mk

# 2. Bluetooth Configuration

# make sure BOARD_HAVE_BLUETOOTH is true for every bt vendor

#BOARD_HAVE_BLUETOOTH := true

#BOARD_HAVE_BLUETOOTH_BCM := true

#SW_BOARD_HAVE_BLUETOOTH_NAME := ap6210

#SW_BOARD_HAVE_BLUETOOTH_NAME := ap6330

#BOARD_HAVE_BLUETOOTH_RTK := true

#BLUETOOTH_HCI_USE_RTK_H5 := true

#SW_BOARD_HAVE_BLUETOOTH_NAME := rtl8723bs

4、

W:\a33\rtl8188eu_sc3817r_sina33\android\device\softwinner\astar-y3\init.sun8i.rc

## bluetooth

# # UART device

# chmod 0660 /dev/ttyS1

# chown bluetooth net_bt_stack /dev/ttyS1

# # power up/down interface

# chmod 0660 /sys/class/rfkill/rfkill0/state

# chmod 0660 /sys/class/rfkill/rfkill0/type

# chown bluetooth net_bt_stack /sys/class/rfkill/rfkill0/state

# chown bluetooth net_bt_stack /sys/class/rfkill/rfkill0/type

# write /sys/class/rfkill/rfkill0/state 0

# # bluetooth LPM

# chmod 0220 /proc/bluetooth/sleep/lpm

# chmod 0220 /proc/bluetooth/sleep/btwrite

# chown bluetooth net_bt_stack /proc/bluetooth/sleep/lpm

# chown bluetooth net_bt_stack /proc/bluetooth/sleep/btwrite

# write /proc/bluetooth/sleep/lpm 1

#2G or 3G init.rc

#import init.sunxi.3gdongle.rc

5、

W:\a33\rtl8188eu_sc3817r_sina33\android\frameworks\base\packages\SettingsProvider\res\values\defaults.xml

6、

W:\a33\rtl8188eu_sc3817r_sina33\lichee\tools\pack\chips\sun8iw5p1\configs\default\env.cfg

bootdelay=3

loglevel=8

7、

W:\a33\rtl8188eu_sc3817r_sina33\lichee\tools\pack\chips\sun8iw5p1\configs\y3\sys_config.fex

;wakeup_src_bt = port:PL09<4><default><default><0>

;----------------------------------------------------------------------------------

;capacitor tp configuration

;ctp_twi_id : twi controller ID

;ctp_twi_addr : I2C slave address, 7bit

;ctp_screen_max_x/_y : resolution of touch panel

;ctp_revert_x/_y_flag : whether need to revert x/y

;ctp_exchange_x_y_flag: whether need to exchange the value of x and y

;ctp_int_port : port for tp's interrupt signal

;ctp_wakeup : port for wakeup tp

;----------------------------------------------------------------------------------

[ctp_para]

ctp_used = 1

ctp_name = "gt82x"

ctp_twi_id = 0

ctp_twi_addr = 0x5d

ctp_screen_max_x = 1280

ctp_screen_max_y = 800

ctp_revert_x_flag = 1

ctp_revert_y_flag = 1

ctp_exchange_x_y_flag = 1

ctp_int_port = port:PL04<4><default><default><default>

ctp_wakeup = port:PL03<1><default><default><1>

ctp_power_ldo =

ctp_power_ldo_vol =

ctp_power_io =

;----------------------------------------------------------------------------------

;lcd0 configuration

;lcd_if: 0:hv(sync+de); 1:8080; 2:ttl; 3:lvds; 4:dsi; 5:edp; 6:extend dsi

;lcd_x: lcd horizontal resolution

;lcd_y: lcd vertical resolution

;lcd_width: width of lcd in mm

;lcd_height: height of lcd in mm

;lcd_dclk_freq: in MHZ unit

;lcd_pwm_freq: in HZ unit

;lcd_pwm_pol: lcd backlight PWM polarity

;lcd_pwm_max_limit lcd backlight PWM max limit(<=255)

;lcd_hbp: hsync back porch

;lcd_ht: hsync total cycle

;lcd_vbp: vsync back porch

;lcd_vt: vysnc total cycle

;lcd_hspw: hsync plus width

;lcd_vspw: vysnc plus width

;lcd_lvds_if: 0:single link; 1:dual link

;lcd_lvds_colordepth: 0:8bit; 1:6bit

;lcd_lvds_mode: 0:NS mode; 1:JEIDA mode

;lcd_frm: 0:disable; 1:enable rgb666 dither; 2:enable rgb656 dither

;lcd_io_phase: 0:noraml; 1:intert phase(0~3bit: vsync phase; 4~7bit:hsync phase;

; 8~11bit:dclk phase; 12~15bit:de phase)

;lcd_gamma_en lcd gamma correction enable

;lcd_bright_curve_en lcd bright curve correction enable

;lcd_cmap_en lcd color map function enable

;deu_mode 0:smoll lcd screen; 1:large lcd screen(larger than 10inch)

;lcdgamma4iep: Smart Backlight parameter, lcd gamma vale * 10;

; decrease it while lcd is not bright enough; increase while lcd is too bright

;smart_color 90:normal lcd screen 65:retina lcd screen(9.7inch)

;----------------------------------------------------------------------------------

[lcd0_para]

lcd_used = 1

lcd_driver_name = "default_lcd"

lcd_if = 3

lcd_x = 1280

lcd_y = 800

lcd_width = 150

lcd_height = 94

lcd_dclk_freq = 71

lcd_pwm_used = 1

lcd_pwm_ch = 0

lcd_pwm_freq = 50000

lcd_pwm_pol = 1

lcd_hbp = 20

lcd_ht = 1418

lcd_hspw = 10

lcd_vbp = 10

lcd_vt = 830

lcd_vspw = 5

lcd_lvds_if = 0

lcd_lvds_colordepth = 1

lcd_lvds_mode = 0

lcd_frm = 1

lcd_gamma_en = 0

lcd_bright_curve_en = 0

lcd_cmap_en = 0

deu_mode = 0

lcdgamma4iep = 22

smart_color = 90

lcd_bl_en = port:PD13<1><0><default><1>

lcd_power = "axp22_dc1sw"

lcdd0 = port:PD18<3><0><default><default>

lcdd1 = port:PD19<3><0><default><default>

lcdd2 = port:PD20<3><0><default><default>

lcdd3 = port:PD21<3><0><default><default>

lcdd4 = port:PD22<3><0><default><default>

lcdd5 = port:PD23<3><0><default><default>

lcdd6 = port:PD24<3><0><default><default>

lcdd7 = port:PD25<3><0><default><default>

lcdd8 = port:PD26<3><0><default><default>

lcdd9 = port:PD27<3><0><default><default>

;----------------------------------------------------------------------------------

;pwm config

;----------------------------------------------------------------------------------

[pwm0_para]

pwm_used = 0

pwm_positive = port:PH00<2><0><default><default>

[pwm1_para]

pwm_used = 1

pwm_positive = port:PH01<2><0><default><default>

;----------------------------------------------------------------------------------

;usb configuration

;usb_used: usb controller enable, 0-disable, 1-enable

;usb_port_type: usb mode: 0-device, 1-host, 2-otg

;usb_detect_type: usb hotplug detect mode, 0-none, 1-vbus/id detect, 2-id/dpdm detect

;usb_id_gpio: usb id detect IO

;usb_det_vbus_gpio: usb vbus detect IO, "axp_ctrl" for axp

;usb_drv_vbus_gpio: usb dirve vbus IO

;usb_restrict_gpio: usb current restrict IO

;usb_restric_flag: usb current restrict flag

;----------------------------------------------------------------------------------

[usbc0]

usb_used = 1

usb_port_type = 0

usb_detect_type = 1

usb_id_gpio = port:PD10<0><1><default><default>

usb_det_vbus_gpio = "axp_ctrl"

usb_drv_vbus_gpio = port:power4<1><0><default><0>

usb_restrict_gpio =

usb_host_init_state = 0

usb_restric_flag = 0

usb_restric_voltage = 3550000

usb_restric_capacity= 5

usb_regulator_io = "nocare"

usb_regulator_vol = 0

usb_regulator_id_vbus = "axp22_dcdc1"

usb_regulator_id_vbus_vol = 3000000

[usbc1]

usb_used = 1

usb_port_type = 1

usb_detect_type = 0

usb_id_gpio =

usb_drv_vbus_gpio = port:PD12<1><0><default><0>

usb_restrict_gpio =

usb_host_init_state = 0

usb_restric_flag = 0

usb_regulator_io = "nocare"

usb_regulator_vol = 0

usb_not_suspend = 0

;--------------------------------------------------------------------------------

;blue tooth

;bt_used ---- blue tooth used (0- no used, 1- used)

;bt_uard_id ---- uart index

;--------------------------------------------------------------------------------

[bt_para]

bt_used = 0

bt_uart_id = 1

阅读全文

0 0