Arduino--基础(四)--weMos D1与DHT11一起使用
来源:互联网 发布:php上传文件源码 编辑:程序博客网 时间:2024/05/21 18:49
参考:https://www.cnx-software.com/2016/03/22/getting-started-with-wemos-d1-mini-esp8266-board-dht-relay-shields/
电路连接原理图:
串口显示:
测试代码:
/* DHT Pro Shield - Simple * * Example testing sketch for various DHT humidity/temperature sensors * Written by ladyada, public domain * * Depends on Adafruit DHT Arduino library * https://github.com/adafruit/DHT-sensor-library */#include "DHT.h"#define DHTPIN D4 // what pin we're connected to// Uncomment whatever type you're using!#define DHTTYPE DHT11 // DHT 11//#define DHTTYPE DHT22 // DHT 22 (AM2302)//#define DHTTYPE DHT21 // DHT 21 (AM2301)// Connect pin 1 (on the left) of the sensor to +5V// NOTE: If using a board with 3.3V logic like an Arduino Due connect pin 1// to 3.3V instead of 5V!// Connect pin 2 of the sensor to whatever your DHTPIN is// Connect pin 4 (on the right) of the sensor to GROUND// Connect a 10K resistor from pin 2 (data) to pin 1 (power) of the sensor// Initialize DHT sensor.// Note that older versions of this library took an optional third parameter to// tweak the timings for faster processors. This parameter is no longer needed// as the current DHT reading algorithm adjusts itself to work on faster procs.DHT dht(DHTPIN, DHTTYPE);void setup() { Serial.begin(9600); Serial.println("DHTxx test!"); dht.begin();}void loop() { // Wait a few seconds between measurements. delay(2000); // Reading temperature or humidity takes about 250 milliseconds! // Sensor readings may also be up to 2 seconds 'old' (its a very slow sensor) float h = dht.readHumidity(); // Read temperature as Celsius (the default) float t = dht.readTemperature(); // Read temperature as Fahrenheit (isFahrenheit = true) float f = dht.readTemperature(true); // Check if any reads failed and exit early (to try again). if (isnan(h) || isnan(t) || isnan(f)) { Serial.println("Failed to read from DHT sensor!"); return; } // Compute heat index in Fahrenheit (the default) float hif = dht.computeHeatIndex(f, h); // Compute heat index in Celsius (isFahreheit = false) float hic = dht.computeHeatIndex(t, h, false); Serial.print("Humidity: "); Serial.print(h); Serial.print(" %\t"); Serial.print("Temperature: "); Serial.print(t); Serial.print(" *C "); Serial.print(f); Serial.print(" *F\t"); Serial.print("Heat index: "); Serial.print(hic); Serial.print(" *C "); Serial.print(hif); Serial.println(" *F");}
阅读全文
0 0
- Arduino--基础(四)--weMos D1与DHT11一起使用
- Arduino--基础(四)--weMos D1 ESP8266模块的使用
- WeMos D1 R2使用笔记
- Arduino--基础(五)--DHT11模块的使用
- 使用Arduino与DHT11监测温湿度
- 使用Arduino与DHT11监测温湿度
- 使用Arduino与DHT11监测温湿度
- 使用Arduino与DHT11监测温湿度
- 20141116 【 Arduino - DHT11 】 温湿度传感器DHT11使用
- Arduino使用温湿度传感器DHT11
- Arduino使用温湿度传感器DHT11(补充说明)
- WeMos D1 GPIO引脚定义
- WeMos D1 GPIO引脚定义
- DHT11 温湿度传感器使用 - arduino - avr
- GPS OLED DHT11 Arduino
- Arduino - DHT11温湿度传感器
- arduino DHT11 温湿度传感器
- 【Arduino】使用LCD1602和DHT11制作温湿度显示器
- 关于.net c#在获取请求参数的时候,一个参数总是获取得逗号分隔的重复值情况原因之一
- Vue2.0使用props传递数据---6
- zk实现分布式锁
- linux权限和指令
- hduoj 2005
- Arduino--基础(四)--weMos D1与DHT11一起使用
- Nginx下limit_req模块burst参数超详细解析
- OpenCV
- 进程、线程的优缺点
- echo 写设备节点后无限循环调用linux驱动下的write函数
- c语言经典例题5
- 欢迎使用CSDN-markdown编辑器
- 栈内存和堆内存案例
- CSS3-转换之translate