使用树莓派CSI摄像头时报错
来源:互联网 发布:刚学完php没有工作经验 编辑:程序博客网 时间:2024/06/06 09:10
mmal: No data received from sensor. Check all connections, including the Sunny one on the camera board
使用命令时:raspistill -t 2000 -o -> my_image.jpg
使用的是树莓派3,系统是raspbian.
各位指点迷津!!!补充一下,红灯有亮
网上分析如下:
分析一、
原因有很多,比如摄像头的sunny部分是否连接牢靠,摄像头是否插紧。但最可能的原因是,你在树莓派带电的时候插拔摄像头,导致管脚烧坏了。这个时候就需要找到是哪个管脚烧坏了,然后补焊一下,加点阻焊剂;
链接:CSI摄像头使用错误
分析二、
This error usually appears because of a faulty connection with the camera. I had the exact same problem in different camera+Pi configurations. The following case is what I encountered:
- The connector is not correctly inserted either in the camera or in the Pi.
- The Sunny connector (the small yellow one on the camera) is not connected well. (now it gets interesting)
- If you often remove and reinsert the camera in the Pi please be sure to remove all power from the Pi. The sensor is very sensitive and a spark on the wrong pin could burn it. (I did this already unfortunately) This could also trigger a problem with the Pi connector pins. It was somewhat confirmed that for Pi2 the connector may have some bad soldering which could lead to cold contact soldering. You can fix this by using some flux on the pins and then pass the soldering iron hot end over the pins to remake the connection.
- I used a longer cable that had both connectors on the same side of the cable. If you connect it like it is you can burn your sensor and the Pi will not start because of the power surge (also the camera gets very hot in this case). DO NOT REMOVE IT from the Pi without removing power before. To a cable like this you have to remove the blue plastic from one end and bend the connector with the contacts on the other side. Insert this end in the camera since this will not be removed/inserted as often as the Pi end.
- 链接:Raspberry camera error: “mmal: No data received from sensor”
分析三、
警告!!!!!!!!!!!!!!!!!!!!!!!!!
绝对不可以带着电源的情况下插入摄像头,如果带电操作,十之八九你的摄像头会GG,博主血泪教训。而且摄像头GG了之后每次调用还是会亮灯,只是你接受不到数据,这个问题我已经Google了很长时间,老外们也是一脸懵逼,大家普遍认为应该是被烧坏了= =
绝对不可以带着电源的情况下插入摄像头,如果带电操作,十之八九你的摄像头会GG,博主血泪教训。而且摄像头GG了之后每次调用还是会亮灯,只是你接受不到数据,这个问题我已经Google了很长时间,老外们也是一脸懵逼,大家普遍认为应该是被烧坏了= =
链接:用树莓派从零开始做一个家庭监控
做了对比,应该是烧了,一开始自己没断电的情况下,插拔过,还接反过,哎,自己竟然这么鱼虫,汗!
阅读全文
0 0
- 使用树莓派CSI摄像头时报错
- 树莓派3 CSI接口摄像头使用问题
- 树莓派3使用CSI摄像头,远程连接
- Raspbian中python使用CSI摄像头
- openCV打开树莓派原装CSI摄像头
- 【树莓派】在OpenCV中调用CSI摄像头
- csi摄像头 raspistill常用命令
- 8、新手入手树莓派教程--csi摄像头的安装
- IMX6q的mipi-csi摄像头
- 树莓派下python,使用USB和CSI摄像头进行视频连续截图,并进行灰度、二值化处理
- DIY网页端的树莓派流畅监控,官方CSI摄像头的正确用法
- hw6ul-lite之CSI摄像头OV7740
- CSI Tool安装使用讲解
- 使用MediaPlayer时报错
- 使用yum时报错
- 树莓派摄像头使用
- 求助 tomcat使用时报错
- 使用maven插件时报错
- 移动构造函数
- iOS应用数据存储的常用方式
- CSS网页底部悬浮代码
- Java进阶之路——从初级程序员到架构师,从小工到专家
- 小白都能看明白的VLAN原理解释
- 使用树莓派CSI摄像头时报错
- 使用Comparatro接口实现自定义排序
- Spark性能优化指南——基础篇
- 设计图标脚本
- 使用iTunes 12.7 可以直接安装ipa安装包
- python生成二维码
- JSTL 标签大全详解
- 分析2012年美国选举数据---映射map/透视表pivot_table/聚合groupby/apply
- -source 7 或更高版本以允许 switch 中存在字符串