DELL VOSTRO 200的sensors-detect 的结果

xj@xj320GBEHD:/media/IT3/mysoft$ sudo sensors-detect
# sensors-detect revision 5249 (2008-05-11 22:56:25 +0200)

This program will help you determine which kernel modules you need
to load to use lm_sensors most effectively. It is generally safe
and recommended to accept the default answers to all questions,
unless you know what you're doing.

We can start with probing for (PCI) I2C or SMBus adapters.
Do you want to probe now? (YES/no): yes
Probing for PCI bus adapters...
Use driver `i2c-i801' for device 0000:00:1f.3: Intel ICH9

We will now try to load each adapter module in turn.
Load `i2c-i801' (say NO if built into your kernel)? (YES/no): yes
Module loaded successfully.
If you have undetectable or unsupported I2C/SMBus adapters, you can have
them scanned by manually loading the modules before running this script.

To continue, we need module `i2c-dev' to be loaded.
Do you want to load `i2c-dev' now? (YES/no):
Module loaded successfully.

We are now going to do the I2C/SMBus adapter probings. Some chips may
be double detected; we choose the one with the highest confidence
value in that case.
If you found that the adapter hung after probing a certain address,
you can specify that address to remain unprobed.

Next adapter: SMBus I801 adapter at 0500 (i2c-0)
Do you want to scan it? (YES/no/selectively):
Client found at address 0x50
Probing for `Analog Devices ADM1033'...                     No
Probing for `Analog Devices ADM1034'...                     No
Probing for `SPD EEPROM'...                                 Yes
    (confidence 8, not a hardware monitoring chip)
Probing for `EDID EEPROM'...                                No
Client found at address 0x52
Probing for `Analog Devices ADM1033'...                     No
Probing for `Analog Devices ADM1034'...                     No
Probing for `SPD EEPROM'...                                 Yes
    (confidence 8, not a hardware monitoring chip)
Probing for `EDID EEPROM'...                                No
Client found at address 0x53
Probing for `Analog Devices ADM1033'...                     No
Probing for `Analog Devices ADM1034'...                     No
Probing for `SPD EEPROM'...                                 Yes
    (confidence 8, not a hardware monitoring chip)
Probing for `EDID EEPROM'...                                No

Some chips are also accessible through the ISA I/O ports. We have to
write to arbitrary I/O ports to probe them. This is usually safe though.
Yes, you do have ISA I/O ports even if you do not have any ISA slots!
Do you want to scan the ISA I/O ports? (YES/no):
Probing for `National Semiconductor LM78' at 0x290...       No
Probing for `National Semiconductor LM78-J' at 0x290...     No
Probing for `National Semiconductor LM79' at 0x290...       No
Probing for `Winbond W83781D' at 0x290...                   No
Probing for `Winbond W83782D' at 0x290...                   No
Probing for `IPMI BMC KCS' at 0xca0...                      No
Probing for `IPMI BMC SMIC' at 0xca8...                     No

Some Super I/O chips may also contain sensors. We have to write to
standard I/O ports to probe them. This is usually safe.
Do you want to scan for Super I/O sensors? (YES/no):
Probing for Super-I/O at 0x2e/0x2f
Trying family `National Semiconductor'...                   No
Trying family `SMSC'...                                     No
Trying family `VIA/Winbond/Fintek'...                       No
Trying family `ITE'...                                      Yes
Found `ITE IT8718F Super IO Sensors'                        Success!
    (address 0x290, driver `it87')
Probing for Super-I/O at 0x4e/0x4f
Trying family `National Semiconductor'...                   No
Trying family `SMSC'...                                     No
Trying family `VIA/Winbond/Fintek'...                       No
Trying family `ITE'...                                      No

Some south bridges, CPUs or memory controllers may also contain
embedded sensors. Do you want to scan for them? (YES/no):
Silicon Integrated Systems SIS5595...                       No
VIA VT82C686 Integrated Sensors...                          No
VIA VT8231 Integrated Sensors...                            No
AMD K8 thermal sensors...                                   No
AMD K10 thermal sensors...                                  No
Intel Core family thermal sensor...                         Success!
    (driver `coretemp')
Intel AMB FB-DIMM thermal sensor...                         No

Now follows a summary of the probes I have just done.
Just press ENTER to continue:

Driver `it87' (should be inserted):
  Detects correctly:
  * ISA bus, address 0x290
    Chip `ITE IT8718F Super IO Sensors' (confidence: 9)

Driver `coretemp' (should be inserted):
  Detects correctly:
  * Chip `Intel Core family thermal sensor' (confidence: 9)

I will now generate the commands needed to load the required modules.
Just press ENTER to continue:

To load everything that is needed, add this to /etc/modules:

#----cut here----
# Chip drivers
it87
coretemp
#----cut here----

Do you want to add these lines automatically? (yes/NO)yes

运行sensors后的结果

当CPU空闲时：

xj@xj320GBEHD:~$ sensors
acpitz-virtual-0
Adapter: Virtual device
temp1:       +40.0°C  (crit = +120.0°C)                  

it8718-isa-0290
Adapter: ISA adapter
in0:         +1.17 V  (min =  +0.00 V, max =  +4.08 V)   
in1:         +3.06 V  (min =  +0.00 V, max =  +4.08 V)   
in2:         +3.36 V  (min =  +3.06 V, max =  +4.08 V)   
in3:         +3.02 V  (min =  +0.00 V, max =  +4.08 V)   
in4:         +3.02 V  (min =  +0.00 V, max =  +4.08 V)   
in5:         +0.06 V  (min =  +0.00 V, max =  +4.08 V)   
in6:         +0.10 V  (min =  +0.00 V, max =  +4.08 V)   
in7:         +2.99 V  (min =  +0.00 V, max =  +4.08 V)   
in8:         +3.04 V
fan1:       1662 RPM  (min =    0 RPM)
fan2:          0 RPM  (min =    0 RPM)
fan3:        841 RPM  (min =    0 RPM)
temp1:       +40.0°C  (low  =  -2.0°C, high = +127.0°C)  sensor = thermal diode
temp2:       +44.0°C  (low  =  -1.0°C, high = +127.0°C)  sensor = thermistor
temp3:       -12.0°C  (low  =  -1.0°C, high = +127.0°C)  sensor = thermistor
cpu0_vid:   +0.000 V

coretemp-isa-0000
Adapter: ISA adapter
Core 0:      +51.0°C  (high = +86.0°C, crit = +100.0°C)  

coretemp-isa-0001
Adapter: ISA adapter
Core 1:      +54.0°C  (high = +86.0°C, crit = +100.0°C)  

当CPU占用率较高时：

xj@xj320GBEHD:~$ sensors
acpitz-virtual-0
Adapter: Virtual device
temp1:       +40.0°C  (crit = +120.0°C)                  

it8718-isa-0290
Adapter: ISA adapter
in0:         +1.17 V  (min =  +0.00 V, max =  +4.08 V)   
in1:         +3.06 V  (min =  +0.00 V, max =  +4.08 V)   
in2:         +3.36 V  (min =  +3.06 V, max =  +4.08 V)   
in3:         +3.02 V  (min =  +0.00 V, max =  +4.08 V)   
in4:         +3.02 V  (min =  +0.00 V, max =  +4.08 V)   
in5:         +0.06 V  (min =  +0.00 V, max =  +4.08 V)   
in6:         +0.10 V  (min =  +0.00 V, max =  +4.08 V)   
in7:         +2.99 V  (min =  +0.00 V, max =  +4.08 V)   
in8:         +3.04 V
fan1:       1683 RPM  (min =    0 RPM)
fan2:          0 RPM  (min =    0 RPM)
fan3:       1062 RPM  (min =    0 RPM)
temp1:       +43.0°C  (low  =  -2.0°C, high = +127.0°C)  sensor = thermal diode
temp2:       +44.0°C  (low  =  -1.0°C, high = +127.0°C)  sensor = thermistor
temp3:       -12.0°C  (low  =  -1.0°C, high = +127.0°C)  sensor = thermistor
cpu0_vid:   +0.000 V

coretemp-isa-0000
Adapter: ISA adapter
Core 0:      +54.0°C  (high = +86.0°C, crit = +100.0°C)  

coretemp-isa-0001
Adapter: ISA adapter
Core 1:      +58.0°C  (high = +86.0°C, crit = +100.0°C)