//在 lk/platform/msm8226/include/platform/aboot.h 中添加 判断 判断pad与pad链接得引脚定义 #define P03_PLUG_IN 15 //GPIO表中查询 //在 lk/platform/msm8226/include/platform/iomap.h中修改 #define RESTART_REASON_ADDR (SYSTEM_IMEM_BASE + 0x565C) //在lk/platform/msm8226/gpio.c中添加如下： int gpio_get(uint32_t gpio){unsigned int *addr = (unsigned int *)GPIO_IN_OUT_ADDR(gpio);return (readl(addr) & 0x1); } //同时修改 gpio_config_blsp_i2c 函数内容 添加case QUP_ID_3 在target_init-> qup_blsp_i2c_init 中用到初始化i2用到 void gpio_config_blsp_i2c(uint8_t blsp_id, uint8_t qup_id){ /* ...*/ case QUP_ID_3: dprintf(CRITICAL, "[I2C] gpio_config_blsp1_i2c: qup3 , i2c_4 \n"); gpio_tlmm_config(10, 3, GPIO_OUTPUT, GPIO_NO_PULL, GPIO_6MA, GPIO_DISABLE); gpio_tlmm_config(11, 3, GPIO_OUTPUT, GPIO_NO_PULL, GPIO_6MA, GPIO_DISABLE); /* ...*/} //在lk/inlcude/gpio.h中添加如下int gpio_get(unsigned nr); ///////////////////////////////////////////////////////////////////////init.c+++ //在lk/target/msms8226/init.c 中添加如下 #include <i2c_qup.h> static struct qup_i2c_dev *dev = NULL;#define SOFTWARE_RESET0x73727374#define ADB_REBOOT0x77665501#define RECOVERY_MODE0x77665502#define UARTLOG_MODE0x77665503#define NORMAL_BOOT0x77665504#define MICROP_CABLE_IN_TRIGGER0x02#define MICROP_POWER_KEY_TRIGGER0x03 #define SCALER_I2C_ADDRESS(0x37)#define SCALER_IMAGE_I2C_ADDRESS(0xE8)#define MICROP_I2C_ADDRESS(0x15)#define MICROP_ID_I2C_ADDRESS(0x00)#define MICROP_FW_ADDRESS(0x01)#define MICROP_POWER_ON_REASON_ADDRESS(0x07)#define MICROP_VBUS_OFF_ADDRESS(0x23)#define MICROP_POWER_OFF_ADDRESS(0x55)#define MICROP_A68_READY_ADDRESS(0x05 uint8_t read_microp_hwid(uint8_t addr){int ret = 0;uint8_t data[4];/* Create a i2c_msg buffer, that is used to put the controller into readmode and then to read some data. */struct i2c_msg msg_buf[] = {{MICROP_I2C_ADDRESS, I2C_M_WR, 1, &addr},{MICROP_I2C_ADDRESS, I2C_M_RD, 4, &data}};dprintf(CRITICAL, "lion->init.c->read_microp_hwid::addr = 0x%d \r\n",addr);ret = qup_i2c_xfer(dev, msg_buf, 2);if ( ret < 0 )return ret;dprintf(INFO, "[BL] ret[0] = 0x%x \n", data[0]);dprintf(INFO, "[BL] ret[1] = 0x%x \n", data[1]);dprintf(INFO, "[BL] ret[2] = 0x%x \n", data[2]);dprintf(INFO, "[BL] ret[3] = 0x%x \n", data[3]);return data[1];}uint8_t read_microp_fw(uint8_t addr){uint8_t data[4];struct i2c_msg msg_buf[] = {{MICROP_I2C_ADDRESS, I2C_M_WR, 1, &addr},{MICROP_I2C_ADDRESS, I2C_M_RD, 4, &data}};dprintf(CRITICAL, "lion->init.c->read_microp_fw::addr = 0x%d \r\n",addr);qup_i2c_xfer(dev, msg_buf, 2);dprintf(INFO, "[BL] ret[0] = 0x%x \n", data[0]);dprintf(INFO, "[BL] ret[1] = 0x%x \n", data[1]);dprintf(INFO, "[BL] ret[2] = 0x%x \n", data[2]);dprintf(INFO, "[BL] ret[3] = 0x%x \n", data[3]);return data[0];}uint8_t read_microp_power_on_reason(uint8_t addr){uint8_t ret[4]; struct i2c_msg msg_buf[] = {{MICROP_I2C_ADDRESS, I2C_M_WR, 1, &addr},{MICROP_I2C_ADDRESS, I2C_M_RD, 4, &ret}};dprintf(CRITICAL, "lion->init.c->read_microp_power_on_reason::addr = 0x%d \r\n",addr);qup_i2c_xfer(dev, msg_buf, 2);dprintf(INFO, "[BL] ret[0] = 0x%x \n", ret[0]);dprintf(INFO, "[BL] ret[1] = 0x%x \n", ret[1]);dprintf(INFO, "[BL] ret[2] = 0x%x \n", ret[2]);dprintf(INFO, "[BL] ret[3] = 0x%x \n", ret[3]);return ret[1];}uint8_t write_microp_a68_ready(uint8_t addr){int ret;uint8_t buf[2];buf[0] = addr;buf[1] = 0x96;struct i2c_msg msg_buf[] = { {MICROP_I2C_ADDRESS, I2C_M_WR, 2, &buf}};dprintf(CRITICAL, "lion->init.c->write_microp_a68_ready::addr = 0x%d \r\n",addr);ret = qup_i2c_xfer(dev, msg_buf, 1);return ret;}uint8_t write_microp_power_off(uint8_t addr){int ret;uint8_t buf[2];buf[0] = addr;buf[1] = 0xAA;struct i2c_msg msg_buf[] = { {MICROP_I2C_ADDRESS, I2C_M_WR, 2, &buf}};dprintf(CRITICAL, "lion->init.c->write_microp_power_off::addr = 0x%d \r\n",addr);ret = qup_i2c_xfer(dev, msg_buf, 1);return ret;}void shutdown_device(void){dprintf(CRITICAL, "Shutdown system.\n");// lk/dev/pmi/pm8921/pm8921.c中实现pm8921_config_reset_pwr_off(0);/* Actually reset the chip */writel(0, MSM_PSHOLD_CTL_SU);mdelay(5000);dprintf(CRITICAL, "Shutdown failed.\n");} ///////////////////////////////////////////////////////////////////////init.c--- ///////////////////////////////////////////////////////////////////////////////////////////////////////////target_init+++ //在void target_init(void) 函数中添加如下判断 void target_init(void) {/*判断是带PAD启动 */ if ( gpio_get(P03_PLUG_IN) ){uint8_t whoamI = 0;unsigned reboot_mode = 0; dprintf(CRITICAL, "lion->tartget_init->[GSBI] qup_i2c_init++\n"); dev = qup_blsp_i2c_init( BLSP_ID_1, QUP_ID_3, 100000, 19200000);dprintf(CRITICAL, "lion->tartget_init->[GSBI] qup_i2c_init--\n");/* Make sure dev is created and initialized properly */if (!dev){ dprintf(CRITICAL, "[GSBI] i2c GSBI init dev fail \n" ); }else{ /*Microp issue*/whoamI = read_microp_hwid( MICROP_ID_I2C_ADDRESS );dprintf(CRITICAL, "lion->tartget_init[Microp] MicropID = 0x%x \n", whoamI);if ( !(whoamI < 0) ){//0x01 whoamI = read_microp_fw(MICROP_FW_ADDRESS); dprintf(CRITICAL, "lion->tartget_init[Microp] Microp FW = 0x3%x \n", whoamI);//0x07whoamI = read_microp_power_on_reason(MICROP_POWER_ON_REASON_ADDRESS);dprintf(CRITICAL, "lion->tartget_init[Microp] Microp power on reason = 0x%x \n", whoamI);/*If sw reset or recovery reset, don't shut down */reboot_mode = readl(RESTART_REASON_ADDR);dprintf(CRITICAL,"lion->tartget_init::reboot_mode : 0x%02x \n", reboot_mode);if ( reboot_mode == SOFTWARE_RESET || reboot_mode == ADB_REBOOT || reboot_mode == UARTLOG_MODE || reboot_mode == NORMAL_BOOT ||reboot_mode == RECOVERY_MODE || whoamI == MICROP_CABLE_IN_TRIGGER || whoamI == MICROP_POWER_KEY_TRIGGER ) { dprintf(CRITICAL, "lion->tartget_init[Microp] Write a68 ready \n");//0x05 write_microp_a68_ready(MICROP_A68_READY_ADDRESS); //vibration_enable(); 震动 暂时没开dprintf(INFO,"lion->tartget_init::reboot_mode : 0x%02x \n", readl(RESTART_REASON_ADDR));}//NOelse{ /*If Cable in or long press P03 power_key*/if ( whoamI == 0x01 || whoamI <= 0 ){ dprintf(CRITICAL, "[Microp] Power off microp \n");//write_microp_vbus_off(MICROP_VBUS_OFF_ADDRESS);write_microp_power_off(MICROP_POWER_OFF_ADDRESS);dprintf(CRITICAL, "[Microp] Power off device \n");shutdown_device(); }}}//end of if ( !(whoamI < 0) ) }//end of else (!dev)} //end of if ( gpio_get(P03_PLUG_IN) )} ///////////////////////////////////////////////////////////////////////////////////////////////////////////target_init---///////////////////////////////////////////////////////////////////////////////// clk++ //使能microp 使用得i2c得时钟 0xF9925000 QUP3 //在lk/platform/msm8226/include/platform/iomap.h 中添加 宏定义 allows SW control of CBC soft macro //// CLK_CTL_BASE 为0xFC400000 QUP3 0xFC400748 #define BLSP1_QUP3_I2C_APPS_CBCR (CLK_CTL_BASE + 0x748)//在/lk/platform/msm8226/msm8226-clock.c中添加如下变量：struct branch_clk gcc_blsp1_qup3_i2c_apps_clk = { .cbcr_reg = BLSP1_QUP3_I2C_APPS_CBCR, .parent = &cxo_clk_src.c, .c = { .dbg_name = "gcc_blsp1_qup3_i2c_apps_clk", .ops = &clk_ops_branch, },//在msm_clocks_8226结构提中添加static struct clk_lookup msm_clocks_8226[] ={/* ...*/ CLK_LOOKUP("blsp1_qup3_i2c_apps_clk", gcc_blsp1_qup3_i2c_apps_clk.c), /* ....*/}///////////////////////////////////////////////////////////////////////////////// clk--
