利用net-snmp读取windows,linux,snmp设备数据(cpu,内存,网卡)
来源:互联网 发布:电脑怎么优化显卡性能 编辑:程序博客网 时间:2024/05/21 09:49
首先编译的时候configure参数加上--with-mib-modules='ucd-snmp/diskio ip-mib/ipv4InterfaceTable'
默认的配置没有这些模块,需要加上
make;make install后,使用命令net-snmp-config --snmpconfpath查看配置文件的目录
然后修改snmp.conf,添加 mibs +ALL
修改snmpd.conf,在rocommunity public default -V systemonly,把 -V systemonly去掉。这是设置权限,去掉后为能访问全部
假设community为public
snmpwalk -v 2c -c public localhost
这时应该会出来好多好多信息
--------------------------------------------------
以下是Linux下一些常用的OID
CPU的
Load
1 minute Load: .1.3.6.1.4.1.2021.10.1.3.1
5 minute Load: .1.3.6.1.4.1.2021.10.1.3.2
15 minute Load: .1.3.6.1.4.1.2021.10.1.3.3
CPU
percentage of user CPU time: .1.3.6.1.4.1.2021.11.9.0
raw user cpu time: .1.3.6.1.4.1.2021.11.50.0
percentages of system CPU time: .1.3.6.1.4.1.2021.11.10.0
raw system cpu time: .1.3.6.1.4.1.2021.11.52.0
percentages of idle CPU time: .1.3.6.1.4.1.2021.11.11.0
raw idle cpu time: .1.3.6.1.4.1.2021.11.53.0
raw nice cpu time: .1.3.6.1.4.1.2021.11.51.0
-------------------------------------------------------------------------------
内存的Total Swap Size: .1.3.6.1.4.1.2021.4.3.0
Available Swap Space: .1.3.6.1.4.1.2021.4.4.0
Total RAM in machine: .1.3.6.1.4.1.2021.4.5.0
Total RAM used: .1.3.6.1.4.1.2021.4.6.0
Total RAM Free: .1.3.6.1.4.1.2021.4.11.0
Total RAM Shared: .1.3.6.1.4.1.2021.4.13.0
Total RAM Buffered: .1.3.6.1.4.1.2021.4.14.0
Total Cached Memory: .1.3.6.1.4.1.2021.4.15.0
-------------------------------------------------------------------
硬盘的The snmpd.conf needs to be edited. Add the following (assuming a machine with a single ‘/’ partition):
disk / 100000 (or)
includeAllDisks 10% for all partitions and disks
The OIDs are as follows
Path where the disk is mounted: .1.3.6.1.4.1.2021.9.1.2.1
Path of the device for the partition: .1.3.6.1.4.1.2021.9.1.3.1
Total size of the disk/partion (kBytes): .1.3.6.1.4.1.2021.9.1.6.1
Available space on the disk: .1.3.6.1.4.1.2021.9.1.7.1
Used space on the disk: .1.3.6.1.4.1.2021.9.1.8.1
Percentage of space used on disk: .1.3.6.1.4.1.2021.9.1.9.1
Percentage of inodes used on disk: .1.3.6.1.4.1.2021.9.1.10.1
----------------------------------------------------------------
以下是windows下常用的OID
CPU
.1.3.6.1.2.1.25.3.3.1.2
如果有一个双核cpu则有2个值,显示当前负载
内存,硬盘
内存跟硬盘都统一在mib2.host.hrStorage里 1.3.6.1.2.1.25.2
hrStorageType节点,hrStorageFixedDisk表示硬盘,hrStorageVirtualMemory是虚拟内存,hrStorageRam是内存
根据id号查:
hrStorageAllocationUnits是簇的大小
hrStorageSize是有多少簇,两者想乘就是总容量
hrStorageUsed是已使用多少,跟总容量相除就是占用率
---------------------------------------------------------------
系统运行时间
System Uptime: .1.3.6.1.2.1.1.3.0
注:linux系统的话也可直接用uptime命令获得
网络设备的
ifIndex 1.3.6.1.2.1.2.2.1.1.0 端口索引号
ifDescr 1.3.6.1.2.1.2.2.1.2.0 端口描述
ifType 1.3.6.1.2.1.2.2.1.3.0 端口类型
ifMtu 1.3.6.1.2.1.2.2.1.4.0 最大传输包字节数
ifSpeed 1.3.6.1.2.1.2.2.1.5.0 端口速度
ifPhysAddress 1.3.6.1.2.1.2.2.1.6.0 物理地址
ifOperStatus 1.3.6.1.2.1.2.2.1.8.0 操作状态
ifLastChange 1.3.6.1.2.1.2.2.1.9.0 上次状态更新时间
ifInOctets 1.3.6.1.2.1.2.2.1.10.0 输入字节数
ifInUcastPkts 1.3.6.1.2.1.2.2.1.11.0 输入非广播包数
ifInNUcastPkts 1.3.6.1.2.1.2.2.1.12.0 输入广播包数
ifInDiscards 1.3.6.1.2.1.2.2.1.13.0 输入包丢弃数
ifInErrors 1.3.6.1.2.1.2.2.1.14.0 输入包错误数
ifInUnknownProtos 1.3.6.1.2.1.2.2.1.15.0 输入未知协议包数
ifOutOctets 1.3.6.1.2.1.2.2.1.16.0 输出字节数
ifOutUcastPkts 1.3.6.1.2.1.2.2.1.17.0 输出非广播包数
ifOutNUcastPkts 1.3.6.1.2.1.2.2.1.18.0 输出广播包数
ifOutDiscards 1.3.6.1.2.1.2.2.1.19.0 输出包丢弃数
ifOutErrors 1.3.6.1.2.1.2.2.1.20.0 输出包错误数
ifOutQLen 1.3.6.1.2.1.2.2.1.21.0 输出队长
流量输出的是计数器,单位是byte,32位
如果流量过大出现统计不正确的情况,就需要编译时加上enable-mfd-rewrites参数,来支持64位的计数器
- 利用net-snmp读取windows,linux,snmp设备数据(cpu,内存,网卡)
- 利用net-snmp读取windows,linux,snmp设备数据(cpu,内存,网卡)
- linux net-snmp agent manager windows snmp
- 用net-snmp获得cpu利用百分比值(转)
- Linux通过snmp采集cpu,内存,磁盘
- windows使用net-snmp
- net-snmp windows安装(mib2c)
- net-snmp windows安装(mib2c)
- java利用snmp4j包来读取snmp协议数据
- windows 下怎样利用NET-SNMP 发送和接收trap
- java利用snmp4j包来读取snmp协议数据(Manager端)
- snmp4j获取数据实例(一,Linux SNMP OID’s for CPU,Memory a)
- snmp4j获取数据实例(一,Linux SNMP OID’s for CPU,Memory a)
- 使用Nagios监控Windows服务器CPU利用率(SNMP方式)
- windows下配置net-snmp
- windows net-snmp安装配置
- Fc4 Linux 上利用net-snmp进行snmpv3测试
- loadrunner通过snmp获取网卡流量数据
- InnoDB: Error: unable to create temporary file
- 利用Python处理文件并注意异常(1)
- HashMap与Hashtable的区别
- 三网融合可借鉴欧盟视听新媒体内容规制
- VC编译错误:uafxcw.lib(afxmem.obj) : error LNK2005: "void * __cdecl operator new(unsigned int)" (??2@YAPA
- 利用net-snmp读取windows,linux,snmp设备数据(cpu,内存,网卡)
- 题目1051:数字阶梯求和
- 数据库分页语句(mysql,oracle,sqlserver,DB2)
- BaseServlet,让一个Servlet可以同时处理多个请求
- SQLSERVER常用操作
- Installation about Windows Slave on Jenkins
- 使用ampser集成工具启动 apache报错
- Android网络编程之Http通信
- thinkphp 模版引用