giky原创，转载须注明作者信息本文论坛连接地址1 拓扑结构
上图中使用CCM4.13与CCM5.0 通过inter-trunk的模式进行互通，公用一台2600系列路由器，并通过FXO连接PSTN。内部网通过一台交换机实现各设备的互联，DHCP做在一台PIX上，并通过PIX连接互联网2 详细配置配置概述：本文档主要涉及Voice 相关的配置，对于数据及安全方面的配置请参考其他资料，同时对CCM的配置中，主要收集两个Cluster之间的配置及落地的配置，其他配置请参考其他文档。IP地址分配表设备 端口Ip 地址FirewallE0192.168.5.254交换机 192.168.5.253Voice GatewayE0192.168.5.246CCM4.13 192.168.5.249CCM5.0 192.168.5.2442.1 Voice Gateway!voice class codec 100 codec preference 1 g711alaw codec preference 2 g711ulaw codec preference 3 g729r8 codec preference 4 g729br8!// 定义网关上的codec class，用于codec转换!interface Ethernet0 ip address 192.168.5.252 255.255.255.0 half-duplexh323-gateway voip bind srcaddr 192.168.5.252!//配置E0 端口，并配置该H.323网关所使用的源地址！ip route 0.0.0.0 0.0.0.0 192.168.5.254!//配置缺省路由!!l!voice-port 1/0/0 cptone CN timeouts call-disconnect 5 timeouts wait-release 5 timing hookflash-out 500 connection plar 2200 supervisory disconnect dualtone mid-call!//配置FXO port，同时设置相关应答/挂断参数!!dial-peer voice 8000 voip destination-pattern .... voice-class codec 100 session target ipv4:192.168.5.249 dtmf-relay h245-signal no vad!//配置指向CCM4.13的Dial Peer！dial-peer voice 1000 pots destination-pattern 9T port 1/0/0//配置落地的Dial Peer!2.2 交换机!Vlan XX Name voice！Vlan YY Name *****Interface vlan XX Ip add xx.xx.xx.xx xx.xx.xx.xx //配置voice vlan interface ip helper-address xx.xx.xx.xx No shutInterface vlan YY Ip add yy.yy.yy.yy yy.yy.yy.yy //配置数据vlan interface No shut!interface FastEthernet x/xdescription phone and PCswitchport access vlan YYswitchport voice vlan XX！2.3 CCM4.132.3.1 配置与CCM5.0 的Inter-Trunk
2.3.2 配置落地网关
2.3.3 配置落地Route Pattern
上图中的Gateway or Route List中，使用了一个GZ RL（Route List），该Route List中加载了一个Route Group，Route Group中绑定了两个网关246和247（247没有体现）
2.3.4 配置与CCM5.0间IP Phone的Route Pattern
2.4 CCM5.02.4.1 配置与CCm4.13的inter Trunk
Add a new trunk
Set the Parameters: Device name: set as you likeDescription: Set as you likeRemote Cisco Callmanager Inforation:Server 1 ip address:[enter the ip address of the primary callmanger]192.168.5.249Other configuration: just let it be
2.4.2 增加落地网关
Add a new h.323 gateway
2.4.3 配置落地Route Pattern配置落地Route pattern，下例仅是针对本地固话的route pattern,对于所有落地的route pattern建议同时建立有确认键“#”和没有“#”的两个Route Pattern
2.4.4 配置与CCm4.13 间的IP Phone的Route Pattern
2.4.5 X-lite配置2.4.5.1 Add a user in CCM5.0
2.4.5.2 Add a device/line in CCM5.0On the Phone configuration page, use the following parameter :• MAC Address :______(MAC address of the PC where the SIP IP Phone is installed)• Device Pool : xxxx• Phone button template : Third-Party SIP Device (Basic)• SIP Phone security profile : Non Secure SIP Profile auth by string• SIP Profile : Standard SIP Profile• Owner ID : 8188
2.4.5.3 X-lite配置Run X-lite，right click the screen. Select SIP accounts settingadd
