Linux route 使用
来源:互联网 发布:编写java游戏小程序 编辑:程序博客网 时间:2024/06/09 20:49
路由表内容说明:
查看路由
# route -n
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
192.57.66.200 192.168.1.1 255.255.255.255 UGH 0 0 0 eth0
192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0
169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0
0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth0
Destination:目标网络或主机。
Gateway:网关地址。
Genmask:目标网络的网络掩码。"255.255.255.255"表示一个主机。"0.0.0.0"表示网关。
Flags:标记。
U、路由被启用。
H、目标是一个主机
G、使用网关。
Linux route 使用
route命令用于显示和操作IP路由表。要实现两个不同的子网之间的通信,需要一台连接两个网络的路由器,或者同时位于两个网络的网关来实现。在Linux系统中,设置路由通常是 为了解决以下问题:该Linux系统在一个局域网中,局域网中有一个网关,能够让机器访问Internet,那么就需要将这台机器的IP地址设置为 Linux机器的默认路由。要注意的是,直接在命令行下执行route命令来添加路由,不会永久保存,当网卡重启或者机器重启之后,该路由就失效了;可以在/etc/rc.local中添加route命令来保证该路由设置永久有效。
格式:route
格式:/sbin/route
用于打印路由表(display the current routing table)。
在非root用户使用时需要使用完整路径执行route命令。
route命令输出的路由表字段含义如下:
Destination 目标
The destination network or destination host. 目标网络或目标主机。
Gateway 网关
The gateway address or '*' if none set. 网关地址,如果没有就显示星号。
Genmask 网络掩码
The netmask for the destination net; '255.255.255.255' for a
host destination and '0.0.0.0' for the default route.
Flags Possible flags include 标志,常用的是U和G。
U (route is up) 路由启用
H (target is a host) 目标是主机
G (use gateway) 使用网关
R (reinstate route for dynamic routing)
D (dynamically installed by daemon or redirect)
M (modified from routing daemon or redirect)
A (installed by addrconf)
C (cache entry)
! (reject route)
Metric 距离、跳数。暂无用。
The 'distance' to the target (usually counted in hops). It is
not used by recent kernels, but may be needed by routing dae-
mons.
Ref 不用管,恒为0。
Number of references to this route. (Not used in the Linux ker-nel.)
Use 该路由被使用的次数,可以粗略估计通向指定网络地址的网络流量。
Count of lookups for the route. Depending on the use of -F and
-C this will be either route cache misses (-F) or hits (-C).
Iface 接口,即eth0,eth0等网络接口名
Interface to which packets for this route will be sent.
格式:route -n
格式:/sbin/route -n
用于打印路由表,加上-n参数就是在输出的信息中不打印主机名而直接打印ip地址。
格式:route add default gw {IP-ADDRESS} {INTERFACE-NAME}
用于设置默认路由,其中,
参数{IP-ADDRESS): 用于指定路由器(网关)的IP地址;
参数{INTERFACE-NAME}: 用于指定接口名称,如eth0。使用/sbin/ifconfig -a可以显示所有接口信息。
例:route add default gw mango
格式:route add -net {NETWORK-ADDRESS} netmask {NETMASK} dev {INTERFACE-NAME}
添加到指定网络的路由规则,其中
参数{NETWORK-ADDRESS}: 用于指定网络地址
参数{NETMASK}: 用于指定子网掩码
参数{INTERFACE-NAME}: 用于指定接口名称,如eth0。
例1:route add -net 192.56.76.0 netmask 255.255.255.0 dev eth0
例2:route add -net 224.0.0.0 netmask 240.0.0.0 dev eth0
格式:route add -net {NETWORK-ADDRESS} netmask {NETMASK} reject
设置到指定网络为不可达,避免在连接到这个网络的地址时程序过长时间的等待,直接就知道该网络不可达。
例:route add -net 10.0.0.0 netmask 255.0.0.0 reject
格式:route del -net {NETWORK-ADDRESS} netmask {NETMASK} dev {INTERFACE-NAME}
格式:route del -net {NETWORK-ADDRESS} netmask {NETMASK} reject
用于删除路由设置。参数指定的方式与route add相似。
查看路由
# route -n
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
192.57.66.200 192.168.1.1 255.255.255.255 UGH 0 0 0 eth0
192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0
169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0
0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth0
Destination:目标网络或主机。
Gateway:网关地址。
Genmask:目标网络的网络掩码。"255.255.255.255"表示一个主机。"0.0.0.0"表示网关。
Flags:标记。
U、路由被启用。
H、目标是一个主机
G、使用网关。
Linux route 使用
route命令用于显示和操作IP路由表。要实现两个不同的子网之间的通信,需要一台连接两个网络的路由器,或者同时位于两个网络的网关来实现。在Linux系统中,设置路由通常是 为了解决以下问题:该Linux系统在一个局域网中,局域网中有一个网关,能够让机器访问Internet,那么就需要将这台机器的IP地址设置为 Linux机器的默认路由。要注意的是,直接在命令行下执行route命令来添加路由,不会永久保存,当网卡重启或者机器重启之后,该路由就失效了;可以在/etc/rc.local中添加route命令来保证该路由设置永久有效。
格式:route
格式:/sbin/route
用于打印路由表(display the current routing table)。
在非root用户使用时需要使用完整路径执行route命令。
route命令输出的路由表字段含义如下:
Destination 目标
The destination network or destination host. 目标网络或目标主机。
Gateway 网关
The gateway address or '*' if none set. 网关地址,如果没有就显示星号。
Genmask 网络掩码
The netmask for the destination net; '255.255.255.255' for a
host destination and '0.0.0.0' for the default route.
Flags Possible flags include 标志,常用的是U和G。
U (route is up) 路由启用
H (target is a host) 目标是主机
G (use gateway) 使用网关
R (reinstate route for dynamic routing)
D (dynamically installed by daemon or redirect)
M (modified from routing daemon or redirect)
A (installed by addrconf)
C (cache entry)
! (reject route)
Metric 距离、跳数。暂无用。
The 'distance' to the target (usually counted in hops). It is
not used by recent kernels, but may be needed by routing dae-
mons.
Ref 不用管,恒为0。
Number of references to this route. (Not used in the Linux ker-nel.)
Use 该路由被使用的次数,可以粗略估计通向指定网络地址的网络流量。
Count of lookups for the route. Depending on the use of -F and
-C this will be either route cache misses (-F) or hits (-C).
Iface 接口,即eth0,eth0等网络接口名
Interface to which packets for this route will be sent.
格式:route -n
格式:/sbin/route -n
用于打印路由表,加上-n参数就是在输出的信息中不打印主机名而直接打印ip地址。
格式:route add default gw {IP-ADDRESS} {INTERFACE-NAME}
用于设置默认路由,其中,
参数{IP-ADDRESS): 用于指定路由器(网关)的IP地址;
参数{INTERFACE-NAME}: 用于指定接口名称,如eth0。使用/sbin/ifconfig -a可以显示所有接口信息。
例:route add default gw mango
格式:route add -net {NETWORK-ADDRESS} netmask {NETMASK} dev {INTERFACE-NAME}
添加到指定网络的路由规则,其中
参数{NETWORK-ADDRESS}: 用于指定网络地址
参数{NETMASK}: 用于指定子网掩码
参数{INTERFACE-NAME}: 用于指定接口名称,如eth0。
例1:route add -net 192.56.76.0 netmask 255.255.255.0 dev eth0
例2:route add -net 224.0.0.0 netmask 240.0.0.0 dev eth0
格式:route add -net {NETWORK-ADDRESS} netmask {NETMASK} reject
设置到指定网络为不可达,避免在连接到这个网络的地址时程序过长时间的等待,直接就知道该网络不可达。
例:route add -net 10.0.0.0 netmask 255.0.0.0 reject
格式:route del -net {NETWORK-ADDRESS} netmask {NETMASK} dev {INTERFACE-NAME}
格式:route del -net {NETWORK-ADDRESS} netmask {NETMASK} reject
用于删除路由设置。参数指定的方式与route add相似。
0 0
- Linux route 使用
- linux route使用
- linux route命令使用
- linux route命令使用
- linux route命令使用
- linux route命令使用
- linux route命令使用
- Linux route 使用
- linux route命令使用
- Linux route 使用
- linux route命令使用
- linux route命令的使用
- linux下route命令使用
- linux route命令的使用详解
- linux route命令的使用详解
- linux route命令的使用详解
- linux route命令的使用详解
- linux route命令的使用详解
- Linux下通过crontab及expect实现自动化处理
- Majority Element
- Oracle APEX 4.2安装 与Oracle PL/SQL Gateway的配置
- 主从错误UUID
- 【数据结构】堆heap,Trie树,位图Bitmap
- Linux route 使用
- 蓝桥杯 VIP 基础练习 Huffuman树
- MySQL中整各种int类型的范围和存储大小
- 一句话记录:Winform编程中Label文本不显示“&”的奇葩问题
- Java基础学习——异常处理
- Windows下安装Hadoop
- Mysql建表与索引使用规范详解
- tomcat服务器解析(一)
- linux 开机自动启动一些服务