Chipsee BeagleBone Black完整启动日志

Xshell for Xmanager Enterprise 5 (Build 0436)
Copyright (c) 2002-2014 NetSarang Computer, Inc. All rights reserved.


Type `help' to learn how to use Xshell prompt.
[C:\Users\zhwx]$ 


Connecting to COM3...
Connected.




U-Boot SPL 2011.09 (Aug 31 2015 - 16:46:38)
Chipsee AM335x EVM Board
OMAP SD/MMC: 0
reading u-boot.img
reading u-boot.img




U-Boot 2011.09 (Aug 31 2015 - 16:46:38)


I2C:   ready
DRAM:  512 MiB
WARNING: Caches not enabled
NAND:  HW ECC Hamming Code selected
No NAND device found!!!
0 MiB
MMC:   OMAP SD/MMC: 0, OMAP SD/MMC: 1
*** Warning - readenv() failed, using default environment


Net:   cpsw
Hit any key to stop autoboot:  0 
SD/MMC found on device 0
reading uEnv.txt


200 bytes read
Loaded environment from uEnv.txt
Importing environment from mmc ...
Running uenvcmd ...
reading uImage


3328672 bytes read
## Booting kernel from Legacy Image at 81000000 ...
   Image Name:   Linux-3.2.0
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3328608 Bytes = 3.2 MiB
   Load Address: 80008000
   Entry Point:  80008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK


Starting kernel ...


Uncompressing Linux... done, booting the kernel.
[    0.000000] Linux version 3.2.0 (zhwx@Myboot) (gcc version 4.5.3 20110311 (prerelease) (GCC) ) #2 Mon Aug 31 19:36:38 CST 2015
[    0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine: am335xevm
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] AM335X ES2.0 (sgx neon )
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 130048
[    0.000000] Kernel command line: console=ttyO0,115200n8 mem=512M root=/dev/mmcblk0p2 rw rootfstype=ext3 rootwait rootdelay=1 init=/init ip=off
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 512MB = 512MB total
[    0.000000] Memory: 512840k/512840k available, 11448k reserved, 0K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xe0800000 - 0xff000000   ( 488 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xe0000000   ( 512 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc05eb000   (6028 kB)
[    0.000000]       .init : 0xc05eb000 - 0xc0627000   ( 240 kB)
[    0.000000]       .data : 0xc0628000 - 0xc0690b20   ( 419 kB)
[    0.000000]        .bss : 0xc0690b44 - 0xc06bfa24   ( 188 kB)
[    0.000000] NR_IRQS:396
[    0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts
[    0.000000] Total of 128 interrupts on 1 active controller
[    0.000000] OMAP clockevent source: GPTIMER2 at 24000000 Hz
[    0.000000] omap_dm_timer_switch_src: Switching to HW default clocksource(sys_clkin_ck) for timer1, this may impact timekeeping in low power state
[    0.000000] OMAP clocksource: GPTIMER1 at 24000000 Hz
[    0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
[    0.000000] Console: colour dummy device 80x30
[    0.000151] Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736)
[    0.087753] pid_max: default: 32768 minimum: 301
[    0.087850] Security Framework initialized
[    0.087933] Mount-cache hash table entries: 512
[    0.088238] CPU: Testing write buffer coherency: ok
[    0.107547] omap_hwmod: pruss: failed to hardreset
[    0.108460] print_constraints: dummy: 
[    0.108736] NET: Registered protocol family 16
[    0.110370] OMAP GPIO hardware version 0.1
[    0.112326] omap_mux_init: Add partition: #1: core, flags: 0
[    0.113804]  omap_i2c.1: alias fck already exists
[    0.114481]  omap2_mcspi.1: alias fck already exists
[    0.114650]  omap2_mcspi.2: alias fck already exists
[    0.115341]  edma.0: alias fck already exists
[    0.115357]  edma.0: alias fck already exists
[    0.115371]  edma.0: alias fck already exists
[    0.135575] bio: create slab <bio-0> at 0
[    0.137292] SCSI subsystem initialized
[    0.138567] usbcore: registered new interface driver usbfs
[    0.138799] usbcore: registered new interface driver hub
[    0.138955] usbcore: registered new device driver usb
[    0.139082] musb-ti81xx musb-ti81xx: musb0, board_mode=0x13, plat_mode=0x3
[    0.139302] musb-ti81xx musb-ti81xx: musb1, board_mode=0x13, plat_mode=0x1
[    0.140157] omap_i2c omap_i2c.1: bus 1 rev2.4.0 at 100 kHz
[    0.141102] tps65910 1-002d: could not be detected
[    0.142100] Advanced Linux Sound Architecture Driver Version 1.0.24.
[    0.142958] Switching to clocksource gp timer
[    0.154574] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host)
[    0.154720] musb-hdrc musb-hdrc.0: dma type: pio
[    0.154977] MUSB0 controller's USBSS revision = 4ea20800
[    0.154995] musb0: Enabled SW babble control
[    0.155505] musb-hdrc musb-hdrc.0: USB OTG mode controller at e083c000 using PIO, IRQ 18
[    0.155627] musb-hdrc musb-hdrc.1: dma type: pio
[    0.155872] MUSB1 controller's USBSS revision = 4ea20800
[    0.155886] musb1: Enabled SW babble control
[    0.156013] musb-hdrc musb-hdrc.1: MUSB HDRC host driver
[    0.156072] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1
[    0.156178] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    0.156191] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.156201] usb usb1: Product: MUSB HDRC host driver
[    0.156209] usb usb1: Manufacturer: Linux 3.2.0 musb-hcd
[    0.156217] usb usb1: SerialNumber: musb-hdrc.1
[    0.156857] hub 1-0:1.0: USB hub found
[    0.156881] hub 1-0:1.0: 1 port detected
[    0.157318] musb-hdrc musb-hdrc.1: USB Host mode controller at e083e800 using PIO, IRQ 19
[    0.157642] NET: Registered protocol family 2
[    0.157798] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.158043] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[    0.158258] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[    0.158383] TCP: Hash tables configured (established 16384 bind 16384)
[    0.158393] TCP reno registered
[    0.158403] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.158420] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.158555] NET: Registered protocol family 1
[    0.158754] RPC: Registered named UNIX socket transport module.
[    0.158765] RPC: Registered udp transport module.
[    0.158772] RPC: Registered tcp transport module.
[    0.158779] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.158959] NetWinder Floating Point Emulator V0.97 (double precision)
[    0.175798] VFS: Disk quotas dquot_6.5.2
[    0.175855] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.176473] msgmni has been set to 1001
[    0.178887] alg: No test for stdrng (krng)
[    0.179432] io scheduler noop registered
[    0.179443] io scheduler deadline registered
[    0.179504] io scheduler cfq registered (default)
[    0.180414] Could not set LED4 to fully on
[    0.213809] omap_uart.0: ttyO0 at MMIO 0x44e09000 (irq = 72) is a OMAP UART0
[    0.789007] console [ttyO0] enabled
[    0.793145] omap_uart.1: ttyO1 at MMIO 0x48022000 (irq = 73) is a OMAP UART1
[    0.800838] omap_uart.2: ttyO2 at MMIO 0x48024000 (irq = 74) is a OMAP UART2
[    0.808530] omap_uart.3: ttyO3 at MMIO 0x481a6000 (irq = 44) is a OMAP UART3
[    0.816218] omap_uart.4: ttyO4 at MMIO 0x481a8000 (irq = 45) is a OMAP UART4
[    0.823907] omap_uart.5: ttyO5 at MMIO 0x481aa000 (irq = 46) is a OMAP UART5
[    0.831929] omap4_rng omap4_rng: OMAP4 Random Number Generator ver. 2.00
[    0.846003] brd: module loaded
[    0.852908] loop: module loaded
[    0.856393] i2c-core: driver [tsl2550] using legacy suspend method
[    0.862854] i2c-core: driver [tsl2550] using legacy resume method
[    0.869288] at24 1-0050: 32768 byte 24c256 EEPROM, writable, 64 bytes/write
[    0.876575] The board is a Chipsee Beaglebone Black Expansion.
[    0.883034]  omap_hsmmc.0: alias fck already exists
[    0.888447]  omap_hsmmc.1: alias fck already exists
[    0.894084]  da8xx_lcdc.0: alias fck already exists
[    0.899483] da8xx_lcdc da8xx_lcdc.0: GLCD: Found HJ070NA13A panel
[    0.905881] ==========zhwx===fb_probe===bpp is [32]
[    0.917399] ==========zhwx===fb_check_var===bpp is [32]
[    0.922864] ==========zhwx===da8xxfb_set_par===bpp is [32]
[    0.928608] ==========zhwx===da8xxfb_set_par===raster_order is [0]
[    0.936072] ==========zhwx===lcd_init===bpp is [32]
[    0.941176] ==========zhwx===lcd_cfg_frame_buffer===bpp is [32]
[    0.947992] ==========zhwx===da8xxfb_set_par===bpp is [32]
[    0.948001] ==========zhwx===da8xxfb_set_par===raster_order is [0]
[    0.949005] ==========zhwx===lcd_init===bpp is [32]
[    0.949018] ==========zhwx===lcd_cfg_frame_buffer===bpp is [32]
[    0.958866] Console: switching to colour frame buffer device 128x37
[    0.998809]  omap_i2c.2: alias fck already exists
[    1.004138] omap_i2c omap_i2c.2: bus 2 rev2.4.0 at 100 kHz
[    1.011021]  davinci-mcasp.0: alias fck already exists
[    1.017260]  d_can.0: alias fck already exists
[    1.024600] mtdoops: mtd device (mtddev=name/number) must be supplied
[    1.031639] omap2-nand driver initializing
[    1.036103] OneNAND driver initializing
[    1.041084] CAN device driver interface
[    1.045139] CAN bus driver for Bosch D_CAN controller 1.0
[    1.051555] d_can d_can.0: device registered (irq=52, irq_obj=53)
[    1.103009] davinci_mdio davinci_mdio.0: davinci mdio revision 1.6
[    1.109477] davinci_mdio davinci_mdio.0: detected phy mask fffffffe
[    1.116628] davinci_mdio.0: probed
[    1.120185] davinci_mdio davinci_mdio.0: phy[0]: device 0:00, driver SMSC LAN8710/LAN8720
[    1.129004] usbcore: registered new interface driver zd1201
[    1.135006] usbcore: registered new interface driver cdc_ether
[    1.141216] usbcore: registered new interface driver cdc_eem
[    1.147304] usbcore: registered new interface driver dm9601
[    1.153178] cdc_ncm: 04-Aug-2011
[    1.156675] usbcore: registered new interface driver cdc_ncm
[    1.162589] Initializing USB Mass Storage driver...
[    1.167866] usbcore: registered new interface driver usb-storage
[    1.174160] USB Mass Storage support registered.
[    1.179336] mousedev: PS/2 mouse device common for all mice
[    1.185782] ft5x06_ts 2-0038: failed to probe FT5X0X touchscreen device
[    1.193294] input: ti-tsc as /devices/platform/omap/ti_tscadc/tsc/input/input0
[    1.201596] rtc-pcf8563 2-0051: chip found, driver version 0.4.3
[    1.209465] rtc-pcf8563 2-0051: low voltage detected, date/time is not reliable.
[    1.217212] rtc-pcf8563 2-0051: retrieved date/time is not valid.
[    1.223882] rtc-pcf8563 2-0051: rtc core: registered rtc-pcf8563 as rtc0
[    1.230999] i2c /dev entries driver
[    1.235131] Linux video capture interface: v2.00
[    1.240206] usbcore: registered new interface driver uvcvideo
[    1.246231] USB Video Class driver (1.1.1)
[    1.523793] OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec
[    1.530284] _regulator_get: deviceless supply vdd_mpu not found, using dummy regulator
[    1.538930] cpuidle: using governor ladder
[    1.543634] cpuidle: using governor menu
[    1.551511] omap4_aes_mod_init: loading AM33X AES driver
[    1.557195] omap4-aes omap4-aes: AM33X AES hw accel rev: 3.02
[    1.563849] omap4_aes_probe: probe() done
[    1.568223] omap4_sham_mod_init: loading AM33X SHA/MD5 driver
[    1.574357] omap4-sham omap4-sham: AM33X SHA/MD5 hw accel rev: 4.03
[    1.587891] omap4_sham_probe: probe() done
[    1.597247] usbcore: registered new interface driver usbhid
[    1.603095] usbhid: USB HID core driver
[    1.607617] tiadc tiadc: attached adc driver
[    1.612670] usbcore: registered new interface driver snd-usb-audio
[    1.620670] _regulator_get: 2-001b supply IOVDD not found, using dummy regulator
[    1.628487] _regulator_get: 2-001b supply DVDD not found, using dummy regulator
[    1.636169] _regulator_get: 2-001b supply AVDD not found, using dummy regulator
[    1.643853] _regulator_get: 2-001b supply DRVDD not found, using dummy regulator
[    1.653661] asoc: tlv320aic3x-hifi <-> davinci-mcasp.0 mapping ok
[    1.661085] ALSA device list:
[    1.664223]   #0: AM335X EVM
[    1.667229] oprofile: hardware counters not available
[    1.672504] oprofile: using timer interrupt.
[    1.676993] nf_conntrack version 0.5.0 (8013 buckets, 32052 max)
[    1.683738] ip_tables: (C) 2000-2006 Netfilter Core Team
[    1.689383] TCP cubic registered
[    1.692756] NET: Registered protocol family 17
[    1.697441] can: controller area network core (rev 20090105 abi 8)
[    1.703988] NET: Registered protocol family 29
[    1.708648] can: raw protocol (rev 20090105)
[    1.713121] can: broadcast manager protocol (rev 20090105 t)
[    1.719065] Registering the dns_resolver key type
[    1.724048] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
[    1.732061] ThumbEE CPU extension supported.
[    1.736591] mux: Failed to setup hwmod io irq -22
[    1.742043] Power Management for AM33XX family
[    1.746901] Trying to load am335x-pm-firmware.bin (60 secs timeout)
[    1.753595] Copied the M3 firmware to UMEM
[    1.757948] Cortex M3 Firmware Version = 0x18
[    1.763067] sr_init: platform driver register failed
[    1.771019] clock: disabling unused clocks to save power
[    1.785936] Detected MACID=6c:ec:eb:a5:96:7f
[    1.791241] cpsw: Detected MACID = 6c:ec:eb:a5:98:81
[    1.798936] rtc-pcf8563 2-0051: low voltage detected, date/time is not reliable.
[    1.806705] rtc-pcf8563 2-0051: retrieved date/time is not valid.
[    1.813087] rtc-pcf8563 2-0051: hctosys: invalid date/time
[    1.819101] Waiting 1sec before mounting root device...
[    1.834306] mmc0: host does not support reading read-only switch. assuming write-enable.
[    1.847031] mmc0: new high speed SDHC card at address aaaa
[    1.853315] mmcblk0: mmc0:aaaa SU08G 7.40 GiB 
[    1.859758]  mmcblk0: p1 p2
[    1.950531] mmc1: new high speed MMC card at address 0001
[    1.956650] mmcblk1: mmc1:0001 MMC04G 3.60 GiB 
[    1.961482] mmcblk1boot0: mmc1:0001 MMC04G partition 1 2.00 MiB
[    1.967829] mmcblk1boot1: mmc1:0001 MMC04G partition 2 2.00 MiB
[    1.975102]  mmcblk1: p1 p2
[    1.979779]  mmcblk1boot1: unknown partition table
[    1.986211]  mmcblk1boot0: unknown partition table
[    4.153600] kjournald starting.  Commit interval 5 seconds
[    4.162583] EXT3-fs (mmcblk0p2): using internal journal
[    4.168068] EXT3-fs (mmcblk0p2): recovery complete
[    4.175572] EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode
[    4.182814] VFS: Mounted root (ext3 filesystem) on device 179:2.
[    4.189374] Freeing init memory: 240K
[    4.194517] Failed to execute /init.  Attempting defaults...
INIT: version 2.88 booting
Starting udev
[    6.636309] EXT4-fs (mmcblk1p2): recovery complete
[    6.641369] EXT4-fs (mmcblk1p2): mounted filesystem with ordered data mode. Opts: (null)
Starting Bootlog daemon: bootlogd: cannot allocate pseudo tty: No such file or directory
bootlogd.
ALSA: Restoring mixer settings...
Configuring network interfaces... [    9.099412] net eth0: CPSW phy found : id is : 0x7c0f1
udhcpc (v1.20.2) started
Sending discover...
Sending discover...
Sending discover...
No lease, failing
done.
[   18.242026] rtc-pcf8563 2-0051: low voltage detected, date/time is not reliable.
[   18.249818] rtc-pcf8563 2-0051: retrieved date/time is not valid.
INIT: Entering runlevel: 5
Starting system message bus: dbus.
Starting Dropbear SSH server: dropbear.
Starting telnet daemon.
Performing wifi calibration...
rm: can't remove '/lib/firmware/ti-connectivity/wl1271-nvs.bin': No such file or directory
Error: Module wl12xx_sdio is not currently loaded
nl80211 not found.
[   18.533514] Disabling lock debugging due to kernel taint
[   18.553062] rtc-pcf8563 2-0051: low voltage detected, date/time is not reliable.
[   18.560816] rtc-pcf8563 2-0051: retrieved date/time is not valid.
Starting network benchmark server: netserver.
Starting syslogd/klogd: done
Starting thttpd.
[   18.736879] ==========zhwx===fb_check_var===bpp is [32]
[   18.736897] ==========zhwx===da8xxfb_set_par===bpp is [32]
[   18.736904] ==========zhwx===da8xxfb_set_par===raster_order is [0]
[   18.740915] ==========zhwx===lcd_init===bpp is [32]
[   18.740932] ==========zhwx===lcd_cfg_frame_buffer===bpp is [32]
[   18.779013] ==========zhwx===fb_check_var===bpp is [32]
[   18.779032] ==========zhwx===da8xxfb_set_par===bpp is [32]
[   18.779039] ==========zhwx===da8xxfb_set_par===raster_order is [0]
[   18.788080] ==========zhwx===lcd_init===bpp is [32]
[   18.788097] ==========zhwx===lcd_cfg_frame_buffer===bpp is [32]
Starting PVR
Starting Lighttpd Web Server: lighttpd.
2017-12-14 00:03:20: (log.c.166) server started 
[   19.410514] ==========zhwx===fb_check_var===bpp is [32]
[   19.410530] ==========zhwx===da8xxfb_set_par===bpp is [32]
[   19.410537] ==========zhwx===da8xxfb_set_par===raster_order is [0]
[   19.427534] ==========zhwx===lcd_init===bpp is [32]
[   19.427551] ==========zhwx===lcd_cfg_frame_buffer===bpp is [32]
/
Starting Matrix GUI application.
[   21.494963]  gadget: Mass Storage Function, version: 2009/09/11
[   21.501187]  gadget: Number of LUNs=1
[   21.505058]  lun0: LUN: removable file: /dev/mmcblk0p1
[   21.510455]  gadget: Mass Storage Gadget, version: 2009/09/11
[   21.516490]  gadget: userspace failed to provide iSerialNumber
[   21.522599]  gadget: g_mass_storage ready
[   21.526810] musb-hdrc musb-hdrc.0: MUSB HDRC host driver
[   21.532394] musb-hdrc musb-hdrc.0: new USB bus registered, assigned bus number 2
[   21.540233] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[   21.547345] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   21.554903] usb usb2: Product: MUSB HDRC host driver
[   21.560092] usb usb2: Manufacturer: Linux 3.2.0 musb-hcd
[   21.565648] usb usb2: SerialNumber: musb-hdrc.0
[   21.570833] hub 2-0:1.0: USB hub found
[   21.574789] hub 2-0:1.0: 1 port detected
***************************************************************
***************************************************************
NOTICE: This file system contains the followin GPLv3 packages:
binutils-symlinks
binutils
gdbserver


If you do not wish to distribute GPLv3 components please remove
the above packages prior to distribution.  This can be done using
the opkg remove command.  i.e.:
    opkg remove <package>
Where <package> is the name printed in the list above


NOTE: If the package is a dependency of another package you
      will be notified of the dependent packages.  You should
      use the --force-removal-of-dependent-packages option to
      also remove the dependent packages as well
***************************************************************
***************************************************************
Stopping Bootlog daemon: bootlogd.


 _____                    _____           _         _   
|  _  |___ ___ ___ ___   |  _  |___ ___  |_|___ ___| |_ 
|     |  _| .'| . | . |  |   __|  _| . | | | -_|  _|  _|
|__|__|_| |__,|_  |___|  |__|  |_| |___|_| |___|___|_|  
              |___|                    |___|            


Arago Project http://arago-project.org am335x-evm ttyO0


Arago 2013.02 am335x-evm ttyO0


am335x-evm login: [   72.270918] ti