标准公差表
来源：互联网 发布：淘宝网食品店 编辑：程序博客网 时间：2024/04/29 22:06
2006-04-19 09:40:30
标准公差表
基本尺寸公差值IT4IT5IT6IT7IT8IT9IT10IT11IT12IT13IT14IT15IT16IT17IT18大于到µmmm-334610142540600.100.140.250.400.601.01.43645812183048750.120.180.300.480.751.21.861046915223658900.150.220.360.580.901.52.210185811182743701100.180.270.430.701.101.82.718306913213352841300.210.330.520.841.302.13.33050711162539621001600.250.390.621.001.602.53.95080813193046741201900.300.460.741.201.903.04.6801201015223554871402200.350.540.871.402.203.55.412018012182540631001602500.400.631.001.602.504.06.318025014202946721151852900.460.721.151.852.904.67.225031516233252811302103200.520.811.302.103.205.28.131540018253657891402303600.570.891.402.303.605.78.940050020274063971552504000.630.971.552.504.006.39.7注：基本尺寸小于1mm时，无IT14至IT18
基本尺寸公差值IT4IT5IT6IT7IT8IT9IT10IT11IT12IT13IT14IT15IT16IT17IT18大于到µmmm-334610142540600.100.140.250.400.601.01.43645812183048750.120.180.300.480.751.21.861046915223658900.150.220.360.580.901.52.210185811182743701100.180.270.430.701.101.82.718306913213352841300.210.330.520.841.302.13.33050711162539621001600.250.390.621.001.602.53.95080813193046741201900.300.460.741.201.903.04.6801201015223554871402200.350.540.871.402.203.55.412018012182540631001602500.400.631.001.602.504.06.318025014202946721151852900.460.721.151.852.904.67.225031516233252811302103200.520.811.302.103.205.28.131540018253657891402303600.570.891.402.303.605.78.940050020274063971552504000.630.971.552.504.006.39.7
- 标准公差表
- 标准公差表
- 基础篇：6）形位公差标注（GD&T标准）；
- 形状公差
- 公差等级
- 公差等级
- 公差与配合part 1
- 公差与配合part 2
- 公差与配合part 3
- 公差与配合part 4
- 公差与配合part 1
- 公差与配合part 2
- 公差与配合part 3
- 公差与配合part 4
- 公差配合及检测技术实用图表
- UG二次开发读取尺寸值公差分析
- 进阶篇：6）公差分析
- 速Geometric.Stackup.2.1.0.15228公差分析
- 塑料模具设计步骤
- 模具精加工控制分析
- 车工加工工序
- 《C专家编程》勘误表
- 虎口脱险
- 标准公差表
- 俄罗斯方块
- 大米有话说
- 网前网恋网事如梦 作者： 一水扬动画坊
- 杀破狼
- 终极斗士2
- 中小企业通用工艺part１
- 中小企业通用工艺part 2
- 中小企业通用工艺part 3
