开发板uboot信息保存
来源:互联网 发布:mysql给表添加分区 编辑:程序博客网 时间:2024/06/06 02:05
U-Boot 1.1.4 (Apr 24 2015 - 17:56:21)
ap143 - Honey Bee 2.0DRAM:
sri
Honey Bee 2.0
ath_ddr_initial_config(195): (16bit) ddr2 init
tap = 0x00000003
Tap (low, high) = (0xa, 0x35)
Tap values = (0x1f, 0x1f, 0x1f, 0x1f)
64 MB
Top of RAM usable for U-Boot at: 84000000
Reserving 198k for U-Boot at: 83fcc000
Reserving 192k for malloc() at: 83f9c000
Reserving 44 Bytes for Board Info at: 83f9bfd4
Reserving 36 Bytes for Global Data at: 83f9bfb0
Reserving 128k for boot params() at: 83f7bfb0
Stack Pointer at: 83f7bf98
Now running in RAM - U-Boot at: 83fcc000
Flash Manuf Id 0xc2, DeviceId0 0x20, DeviceId1 0x18
flash size 16MB, sector count = 256
Flash: 16 MB
*** Warning - bad CRC, using default environment
*** Warning *** : PCIe WLAN Module not found !!!
In: serial
Out: serial
Err: serial
Net: ath_gmac_enet_initialize...
Fetching MAC Address from 0x83fec93c
Fetching MAC Address from 0x83fec93c
ath_gmac_enet_initialize: reset mask:c02200
Scorpion ---->S27 PHY*
S27 reg init
: cfg1 0x800c0000 cfg2 0x7114
eth0: 00:03:7f:11:20:ce
athrs27_phy_setup ATHR_PHY_CONTROL 4 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4 :10
eth0 up
Honey Bee ----> MAC 1 S27 PHY *
S27 reg init
ATHRS27: resetting s27
ATHRS27: s27 reset done
: cfg1 0x800c0000 cfg2 0x7214
eth1: 00:03:7f:11:20:cf
athrs27_phy_setup ATHR_PHY_CONTROL 0 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0 :10
athrs27_phy_setup ATHR_PHY_CONTROL 1 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1 :10
athrs27_phy_setup ATHR_PHY_CONTROL 2 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2 :10
athrs27_phy_setup ATHR_PHY_CONTROL 3 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3 :10
eth1 up
eth0, eth1
Setting 0x181162c0 to 0x4c99a100
Hit any key to stop autoboot: 0
ath>
ath>
ath>
ath>
ath> ?
? - alias for 'help'
autoscr - run script from memory
base - print or set address offset
bdinfo - print Board Info structure
boot - boot default, i.e., run 'bootcmd'
bootd - boot default, i.e., run 'bootcmd'
bootelf - Boot from an ELF image in memory
bootm - boot application image from memory
bootp - boot image via network using BootP/TFTP protocol
bootvx - Boot vxWorks from an ELF image
cmp - memory compare
coninfo - print console devices and information
cp - memory copy
crc32 - checksum calculation
dhcp - invoke DHCP client to obtain IP/boot params
echo - echo args to console
erase - erase FLASH memory
ethreg - Switch/PHY Reg rd/wr utility
exit - exit script
flinfo - print FLASH memory information
go - start application at address 'addr'
help - print online help
iminfo - print header information for application image
itest - return true/false on integer compare
loop - infinite loop on address range
mct - simple RAM test
md - memory display
mii - MII utility commands
mm - memory modify (auto-incrementing)
mtest - simple RAM test
mw - memory write (fill)
nfs - boot image via network using NFS protocol
nm - memory modify (constant address)
pci - list and access PCI Configuration Space
ping - send ICMP ECHO_REQUEST to network host
pll cpu-pll dither ddr-pll dither - Set to change CPU & DDR speed
pll erase
pll get
printenv- print environment variables
progmac - Set ethernet MAC addresses
progmac2 - Set ethernet MAC addresses
protect - enable or disable FLASH write protection
rarpboot- boot image via network using RARP/TFTP protocol
reset - Perform RESET of the CPU
run - run commands in an environment variable
saveenv - save environment variables to persistent storage
setenv - set environment variables
sleep - delay execution for some time
test - minimal test like /bin/sh
tftpboot- boot image via network using TFTP protocol
version - print monitor version
ath> version
U-Boot 1.1.4 (Apr 24 2015 - 17:56:21)
ath> bdinfo
boot_params = 0x83F7BFB0
memstart = 0x80000000
memsize = 0x04000000
flashstart = 0x9F000000
flashsize = 0x01000000
flashoffset = 0x00028780
ethaddr = 00:AA:BB:CC:DD:EE
ip_addr = 192.168.1.1
baudrate = 115200 bps
ath> printenv
bootargs=console=ttyS0,115200 root=31:02 rootfstype=jffs2 init=/sbin/init mtdparts=ath-nor0:256k(u-boot),64k(u-boot-env),14528k(rootfs),1408k(u)
bootcmd=bootm 0x9fE80000
bootdelay=2
baudrate=115200
ethaddr=0x00:0xaa:0xbb:0xcc:0xdd:0xee
ipaddr=192.168.1.1
serverip=192.168.1.10
dir=
lu=tftp 0x80060000 ${dir}u-boot.bin&&erase 0x9f000000 +$filesize&&cp.b $fileaddr 0x9f000000 $filesize
lf=tftp 0x80060000 ${dir}ap143${bc}-jffs2&&erase 0x9f050000 +0xE30000&&cp.b $fileaddr 0x9f050000 $filesize
lk=tftp 0x80060000 ${dir}vmlinux${bc}.lzma.uImage&&erase 0x9fE80000 +$filesize&&cp.b $fileaddr 0x9fE80000 $filesize
stdin=serial
stdout=serial
stderr=serial
ethact=eth0
Environment size: 684/65532 bytes
ath>
ap143 - Honey Bee 2.0DRAM:
sri
Honey Bee 2.0
ath_ddr_initial_config(195): (16bit) ddr2 init
tap = 0x00000003
Tap (low, high) = (0xa, 0x35)
Tap values = (0x1f, 0x1f, 0x1f, 0x1f)
64 MB
Top of RAM usable for U-Boot at: 84000000
Reserving 198k for U-Boot at: 83fcc000
Reserving 192k for malloc() at: 83f9c000
Reserving 44 Bytes for Board Info at: 83f9bfd4
Reserving 36 Bytes for Global Data at: 83f9bfb0
Reserving 128k for boot params() at: 83f7bfb0
Stack Pointer at: 83f7bf98
Now running in RAM - U-Boot at: 83fcc000
Flash Manuf Id 0xc2, DeviceId0 0x20, DeviceId1 0x18
flash size 16MB, sector count = 256
Flash: 16 MB
*** Warning - bad CRC, using default environment
*** Warning *** : PCIe WLAN Module not found !!!
In: serial
Out: serial
Err: serial
Net: ath_gmac_enet_initialize...
Fetching MAC Address from 0x83fec93c
Fetching MAC Address from 0x83fec93c
ath_gmac_enet_initialize: reset mask:c02200
Scorpion ---->S27 PHY*
S27 reg init
: cfg1 0x800c0000 cfg2 0x7114
eth0: 00:03:7f:11:20:ce
athrs27_phy_setup ATHR_PHY_CONTROL 4 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4 :10
eth0 up
Honey Bee ----> MAC 1 S27 PHY *
S27 reg init
ATHRS27: resetting s27
ATHRS27: s27 reset done
: cfg1 0x800c0000 cfg2 0x7214
eth1: 00:03:7f:11:20:cf
athrs27_phy_setup ATHR_PHY_CONTROL 0 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0 :10
athrs27_phy_setup ATHR_PHY_CONTROL 1 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1 :10
athrs27_phy_setup ATHR_PHY_CONTROL 2 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2 :10
athrs27_phy_setup ATHR_PHY_CONTROL 3 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3 :10
eth1 up
eth0, eth1
Setting 0x181162c0 to 0x4c99a100
Hit any key to stop autoboot: 0
ath>
ath>
ath>
ath>
ath> ?
? - alias for 'help'
autoscr - run script from memory
base - print or set address offset
bdinfo - print Board Info structure
boot - boot default, i.e., run 'bootcmd'
bootd - boot default, i.e., run 'bootcmd'
bootelf - Boot from an ELF image in memory
bootm - boot application image from memory
bootp - boot image via network using BootP/TFTP protocol
bootvx - Boot vxWorks from an ELF image
cmp - memory compare
coninfo - print console devices and information
cp - memory copy
crc32 - checksum calculation
dhcp - invoke DHCP client to obtain IP/boot params
echo - echo args to console
erase - erase FLASH memory
ethreg - Switch/PHY Reg rd/wr utility
exit - exit script
flinfo - print FLASH memory information
go - start application at address 'addr'
help - print online help
iminfo - print header information for application image
itest - return true/false on integer compare
loop - infinite loop on address range
mct - simple RAM test
md - memory display
mii - MII utility commands
mm - memory modify (auto-incrementing)
mtest - simple RAM test
mw - memory write (fill)
nfs - boot image via network using NFS protocol
nm - memory modify (constant address)
pci - list and access PCI Configuration Space
ping - send ICMP ECHO_REQUEST to network host
pll cpu-pll dither ddr-pll dither - Set to change CPU & DDR speed
pll erase
pll get
printenv- print environment variables
progmac - Set ethernet MAC addresses
progmac2 - Set ethernet MAC addresses
protect - enable or disable FLASH write protection
rarpboot- boot image via network using RARP/TFTP protocol
reset - Perform RESET of the CPU
run - run commands in an environment variable
saveenv - save environment variables to persistent storage
setenv - set environment variables
sleep - delay execution for some time
test - minimal test like /bin/sh
tftpboot- boot image via network using TFTP protocol
version - print monitor version
ath> version
U-Boot 1.1.4 (Apr 24 2015 - 17:56:21)
ath> bdinfo
boot_params = 0x83F7BFB0
memstart = 0x80000000
memsize = 0x04000000
flashstart = 0x9F000000
flashsize = 0x01000000
flashoffset = 0x00028780
ethaddr = 00:AA:BB:CC:DD:EE
ip_addr = 192.168.1.1
baudrate = 115200 bps
ath> printenv
bootargs=console=ttyS0,115200 root=31:02 rootfstype=jffs2 init=/sbin/init mtdparts=ath-nor0:256k(u-boot),64k(u-boot-env),14528k(rootfs),1408k(u)
bootcmd=bootm 0x9fE80000
bootdelay=2
baudrate=115200
ethaddr=0x00:0xaa:0xbb:0xcc:0xdd:0xee
ipaddr=192.168.1.1
serverip=192.168.1.10
dir=
lu=tftp 0x80060000 ${dir}u-boot.bin&&erase 0x9f000000 +$filesize&&cp.b $fileaddr 0x9f000000 $filesize
lf=tftp 0x80060000 ${dir}ap143${bc}-jffs2&&erase 0x9f050000 +0xE30000&&cp.b $fileaddr 0x9f050000 $filesize
lk=tftp 0x80060000 ${dir}vmlinux${bc}.lzma.uImage&&erase 0x9fE80000 +$filesize&&cp.b $fileaddr 0x9fE80000 $filesize
stdin=serial
stdout=serial
stderr=serial
ethact=eth0
Environment size: 684/65532 bytes
ath>
0 0
- 开发板uboot信息保存
- mini2440开发板移植uboot后norflash环境变量保存
- EVC开发实例二:保存信息
- 【Android 开发教程】保存状态等信息
- iOS开发钥匙串保存信息
- uboot移植(S3Cmini2440开发板)
- UBOOT移植OK210开发板
- uboot 中分区信息
- 在uboot中查看uboot信息
- centillium开发板的UBOOT配置
- minis3c2440嵌入式开发板之uboot详解
- 天嵌TQ2440 ARM开发板Uboot移植
- minis3c2440嵌入式开发板之uboot详解
- 三、开发板UBOOT烧写
- uboot 移到开发板主要命令
- 飞凌OK210开发板UBOOT移植步骤
- OK6410开发板uboot烧写
- 飞凌OK210开发板UBoot移植步骤
- 【Linux命令001】cp命令
- HDU 1106
- 祝贺我的博客访问量过万(访问量:10260次)
- LeetCode: Pascal's Triangle
- 1109. Group Photo (25)
- 开发板uboot信息保存
- 20160314 CodeVS 1005 生日礼物,1031 质数环,1049 棋盘染色
- 简单实现字母快速导航LetterView
- 关于概率期望
- Visual Studio调试小技巧
- python pip 安装包时出错
- iOS开发中那些高效常用的宏
- SQL Server 2012 自动增长列,值跳跃问题
- phpMyAdmin登陆不上的问题