3228交换机链路聚合配置
来源:互联网 发布:低价域名注册 编辑:程序博客网 时间:2024/05/16 15:56
交换机3228-1和交换机3228-2通过smartgroup端口相连,它们分别由2个物理端口聚合而成。smartgroup的端口模式为trunk,承载VLAN10和VLAN20。
7.6 配置步骤
7.6.1 静态聚合
下面以3228-1为例进行配置说明:
/*创建Trunk组*/
ZXR10(config)#interface smartgroup1
/*绑定端口到Trunk组*/
ZXR10(config)#interface fei_1/1
ZXR10(config-if)#smartgroup 1 mode on //设置聚合模式为静态
ZXR10(config)#interface fei_1/2
ZXR10(config-if)#smartgroup 1 mode on
/*修改smartgroup端口的VLAN链路类型*/
ZXR10(config)#interface smartgroup1
ZXR10(config-if)#switchport mode trunk
ZXR10(config-if)#switchport trunk vlan 10 //把smartgroup1端口以trunk方式加入vlan10
ZXR(config-if)#switchport trunk vlan 20
7.6.2 动态聚合
下面以3228-1为例进行配置说明:
/*创建Trunk组*/
ZXR10(config)#interface smartgroup1
/*绑定端口到Trunk组*/
ZXR10(config)#interface fei_1/1
ZXR10(config-if)#smartgroup 1 mode active //设置聚合模式为active
ZXR10(config)#interface fei_1/2
ZXR10(config-if)#smartgroup 1 mode active
/*修改smartgroup端口的VLAN链路类型*/
ZXR10(config)#interface smartgroup1
ZXR10(config-if)#switchport mode trunk
ZXR10(config-if)#switchport trunk vlan 10 //把smartgroup1端口以trunk方式加入vlan10
ZXR(config-if)#switchport trunk vlan 20
注:聚合模式设置为on时端口运行静态trunk,参与聚合的两端都需要设置为on模式。聚合模式设置为active或passive时端口运行LACP,active指端口为主动协商模式,passive指端口为被动协商模式。配置动态链路聚合时,应当将一端端口的聚合模式设置为active,另一端设置为passive,或者两端都设置为active。
7.7 验证方法
使用命令show lacp 1 internal 查看trunk组1中成员端口的聚合状态。Selected表示聚合成功。
ZXR10(config)#show lacp 1 internal
Smartgroup:1
Actor Agg LACPDUs Port Oper Port RX Mux
Port State Interval Priority Key State Machine Machine
-----------------------------------------------------------------------------
fei_1/1 selected 30 32768 0x102 0x3d current distributing
fei_1/2 selected 30 32768 0x102 0x3d current distributing
7.6 配置步骤
7.6.1 静态聚合
下面以3228-1为例进行配置说明:
/*创建Trunk组*/
ZXR10(config)#interface smartgroup1
/*绑定端口到Trunk组*/
ZXR10(config)#interface fei_1/1
ZXR10(config-if)#smartgroup 1 mode on //设置聚合模式为静态
ZXR10(config)#interface fei_1/2
ZXR10(config-if)#smartgroup 1 mode on
/*修改smartgroup端口的VLAN链路类型*/
ZXR10(config)#interface smartgroup1
ZXR10(config-if)#switchport mode trunk
ZXR10(config-if)#switchport trunk vlan 10 //把smartgroup1端口以trunk方式加入vlan10
ZXR(config-if)#switchport trunk vlan 20
7.6.2 动态聚合
下面以3228-1为例进行配置说明:
/*创建Trunk组*/
ZXR10(config)#interface smartgroup1
/*绑定端口到Trunk组*/
ZXR10(config)#interface fei_1/1
ZXR10(config-if)#smartgroup 1 mode active //设置聚合模式为active
ZXR10(config)#interface fei_1/2
ZXR10(config-if)#smartgroup 1 mode active
/*修改smartgroup端口的VLAN链路类型*/
ZXR10(config)#interface smartgroup1
ZXR10(config-if)#switchport mode trunk
ZXR10(config-if)#switchport trunk vlan 10 //把smartgroup1端口以trunk方式加入vlan10
ZXR(config-if)#switchport trunk vlan 20
注:聚合模式设置为on时端口运行静态trunk,参与聚合的两端都需要设置为on模式。聚合模式设置为active或passive时端口运行LACP,active指端口为主动协商模式,passive指端口为被动协商模式。配置动态链路聚合时,应当将一端端口的聚合模式设置为active,另一端设置为passive,或者两端都设置为active。
7.7 验证方法
使用命令show lacp 1 internal 查看trunk组1中成员端口的聚合状态。Selected表示聚合成功。
ZXR10(config)#show lacp 1 internal
Smartgroup:1
Actor Agg LACPDUs Port Oper Port RX Mux
Port State Interval Priority Key State Machine Machine
-----------------------------------------------------------------------------
fei_1/1 selected 30 32768 0x102 0x3d current distributing
fei_1/2 selected 30 32768 0x102 0x3d current distributing
- 3228交换机链路聚合配置
- 2618交换机链路聚合配置
- cisco交换机上的链路聚合
- H3C交换机配置端口聚合
- ibm 刀片 BladeCenter H22 背板交换机链路聚合配置(bnt和nt)
- H3C和CISCO交换机做聚合配置
- 华为32309交换机配置聚合端口
- 思科交换机与H3C交换机端口聚合配置
- 交换机链路聚合在网络中的作用
- 交换机链路聚合在网络中的作用
- 【网络高可用】华为交换机/路由器链路聚合
- 华为链路聚合配置
- cisco交换机端口聚合、VTP、ACL配置实例
- 二层链路聚合和三层链路聚合的配置
- 3228交换机VLAN配置
- 3228交换机STP配置
- 接口篇(5.6) 02. 与思科交换机三层链路聚合连接 ❀ 飞塔 (Fortinet) 防火墙
- 交换机聚合步骤
- 国内从事CV相关的企业
- 3228交换机VLAN配置
- SQLServer2008和Oracle10g分页存储过程
- 组合
- Android开发之解析JSon数据(二)
- 3228交换机链路聚合配置
- 模运算法则
- 数学专业词汇
- C++的三大特性
- 3228交换机STP配置
- 动态创建下拉列表框ComboBox
- 对比 PL/SQL profiler 剖析结果
- hdu 1080 Human Gene Functions(LCS&DP)
- AE中IHookHelper的用法(几点介绍)