cubietruck lubuntu启动信息分析

U-Boot SPL 2014.04 (Nov 05 2014 - 02:17:48)
Board: Cubietruck
DRAM: 2048 MiB
CPU: 960000000Hz, AXI/AHB/APB: 3/2/2
spl: not an uImage at 1600




U-Boot 2014.04 (Nov 05 2014 - 02:17:48) Allwinner Technology


CPU:   Allwinner A20 (SUN7I)
Board: Cubietruck
I2C:   ready
DRAM:  2 GiB
MMC:   SUNXI SD/MMC: 0
*** Warning - bad CRC, using default environment


In:    serial
Out:   serial
Err:   serial
Net:   dwmac.1c50000
Hit any key to stop autoboot:  0 
reading uEnv.txt
266 bytes read in 16 ms (15.6 KiB/s)
Loaded environment from uEnv.txt
Running uenvcmd ...
Y焉 filesystem...
** Unrecognized filesystem type **
Failed to mount ext2 filesystem...
** Unrecognized filesystem type **
reading uImage
 **Unable to read file uImage
sun7i# HELLO! BOOT0 is starting!
boot0 version : 2.0.0



                       read dram para.
dram driver version: 1.15
dram size =2048MB
0xffffffff
super_standby_flag = 0
Succeed in opening nand flash.
block from 2 to 6
deal block 2
Succeed in reading Boot1 file head.
The size of Boot1 is 0x00068000.
The file stored in 0x00000000 of block 2 is perfect.
Check is correct.
Ready to disable icache.
Succeed in loading Boot1.
Jump to Boot1.
[       0.147] boot1 version : 2.0.0
[       0.147] script installed early ok
[       0.148] pmu type = 3
[       0.252] bat vol = 94 mv
[       0.266] axi:ahb:apb=4:2:2
[       0.266] set dcdc2=1450mv, clock=912M successed
[       0.268] key
[       0.281] no key found
[       0.281] flash init start
[       0.281] NB1 : enter NFB_Init
[       0.284] NB1 : enter phy init
[       0.287] [NAND] nand driver(b) version: 0x0x00000002, 0x0x00000012, data: 0x20130627
[       0.295] get the good blk ratio from hwscan : 912 
[       0.300] NB1 : nand phy init ok
[       1.668] _RepairLogBlkTbl start
[       1.670] Log Block Index 0x00000000, LogicBlockNum: 0x000000de, LogBlockType: 0x00000000
[       1.674] log0: 0x000000d2, Log1: 0x0000ffff, WriteIndex: 0x00000000
[       1.681] datablock: 0x000000e4, lastusedpage: 0x000000ed
[       1.688] Log Block Index 0x00000001, LogicBlockNum: 0x00000015, LogBlockType: 0x00000000
[       1.695] log0: 0x00000781, Log1: 0x0000ffff, WriteIndex: 0x00000000
[       1.702] datablock: 0x00000794, lastusedpage: 0x000000fb
[       1.709] Log Block Index 0x00000002, LogicBlockNum: 0x000000b6, LogBlockType: 0x00000000
[       1.716] log0: 0x0000078c, Log1: 0x0000ffff, WriteIndex: 0x00000000
[       1.722] datablock: 0x000007a2, lastusedpage: 0x00000011
[       1.730] Log Block Index 0x00000003, LogicBlockNum: 0x00000067, LogBlockType: 0x00000000
[       1.736] log0: 0x0000073e, Log1: 0x0000ffff, WriteIndex: 0x00000000
[       1.743] datablock: 0x000007b6, lastusedpage: 0x00000013
[       1.750] Log Block Index 0x00000004, LogicBlockNum: 0x00000054, LogBlockType: 0x00000000
[       1.757] log0: 0x000007c7, Log1: 0x0000ffff, WriteIndex: 0x00000000
[       1.763] datablock: 0x000007cb, lastusedpage: 0x0000001d
[       1.771] Log Block Index 0x00000005, LogicBlockNum: 0x00000036, LogBlockType: 0x00000000
[       1.777] log0: 0x000007d4, Log1: 0x0000ffff, WriteIndex: 0x00000000
[       1.784] datablock: 0x00000711, lastusedpage: 0x00000001
[       1.792] Log Block Index 0x00000006, LogicBlockNum: 0x000000df, LogBlockType: 0x00000000
[       1.798] log0: 0x000007be, Log1: 0x0000ffff, WriteIndex: 0x00000000
[       1.805] datablock: 0x000007d8, lastusedpage: 0x00000000
[       1.812] Log Block Index 0x00000007, LogicBlockNum: 0x000000e1, LogBlockType: 0x00000000
[       1.819] log0: 0x000007dd, Log1: 0x0000ffff, WriteIndex: 0x00000000
[       1.825] datablock: 0x000007cf, lastusedpage: 0x00000002
[       1.833] Log Block Index 0x00000008, LogicBlockNum: 0x00000017, LogBlockType: 0x00000000
[       1.839] log0: 0x000007de, Log1: 0x0000ffff, WriteIndex: 0x00000000
[       1.846] datablock: 0x00000785, lastusedpage: 0x0000000b
[       1.854] Log Block Index 0x00000009, LogicBlockNum: 0x00000019, LogBlockType: 0x00000000
[       1.860] log0: 0x000007e1, Log1: 0x0000ffff, WriteIndex: 0x00000000
[       1.867] datablock: 0x0000078a, lastusedpage: 0x000000c3
[       1.874] Log Block Index 0x0000000a, LogicBlockNum: 0x000000c9, LogBlockType: 0x00000000
[       1.881] log0: 0x000007e9, Log1: 0x0000ffff, WriteIndex: 0x00000000
[       1.887] datablock: 0x000007a8, lastusedpage: 0x00000006
[       1.895] Log Block Index 0x0000000b, LogicBlockNum: 0x000000e0, LogBlockType: 0x00000000
[       1.901] log0: 0x00000787, Log1: 0x0000ffff, WriteIndex: 0x00000000
[       1.908] datablock: 0x000007f1, lastusedpage: 0x0000000b
[       1.916] Log Block Index 0x0000000c, LogicBlockNum: 0x0000006e, LogBlockType: 0x00000000
[       1.922] log0: 0x000007f5, Log1: 0x0000ffff, WriteIndex: 0x00000000
[       1.928] datablock: 0x0000077f, lastusedpage: 0x00000007
[       1.936] Log Block Index 0x0000000d, LogicBlockNum: 0x00000071, LogBlockType: 0x00000000
[       1.942] log0: 0x000007db, Log1: 0x0000ffff, WriteIndex: 0x00000000
[       1.949] datablock: 0x000007f7, lastusedpage: 0x000000f0
[       1.956] Log Block Index 0x0000000e, LogicBlockNum: 0x00000014, LogBlockType: 0x00000000
[       1.963] log0: 0x000007f8, Log1: 0x0000ffff, WriteIndex: 0x00000000
[       1.970] datablock: 0x000007cd, lastusedpage: 0x000000da
[       1.977] Log Block Index 0x0000000f, LogicBlockNum: 0x000000c8, LogBlockType: 0x00000000
[       1.984] log0: 0x000007d0, Log1: 0x0000ffff, WriteIndex: 0x00000000
[       1.990] datablock: 0x000007fb, lastusedpage: 0x00000002
[       1.996] _RepairLogBlkTbl end
[       2.017] NB1 : init ok
[       2.017] flash init finish
[       2.018] fs init ok
[       2.020] fattype FAT16
[       2.022] fs mount ok
[       2.026] nand good_block_ratio=912
[       2.028] storage_type=0
[       2.039] 0
[       2.039] set pc
[       2.039] usbdc_vol = 4000, usbdc_cur = 0
[       2.041] usbpc_vol = 4200, usbpc_cur = 0
[       2.045] init to usb pc
[       2.048] set pc
[       2.128] key value = 0
[       2.128] recovery key high 40, low 4
[       2.141] show pic finish
[       2.141] load kernel start
[       2.157] load kernel successed
[       2.157] start address = 0x4a000000
[       2.465] power exit detect


U-Boot 2011.09-rc1-00000-gf75abad-dirty (Oct 21 2013 - 18:44:22) Allwinner Technology 


CPU:   SUNXI Family
Board: A20-Cubietruck
DRAM:  2 GiB
NAND:  NB1 : enter NFB_Init
[NAND] nand driver(b) version: 0x2, 0x12, data: 20130526
[NAND] set nand_good_block_ratio 912 
NB1 : nand phy init ok
NB1 : init ok
3200 MiB
Using default environment


In:    serial
Out:   serial
Err:   serial
--------fastboot partitions--------
-total partitions:3-
-name-        -start-       -size-      
bootloader  : 8000          20000       
rootfs      : 28000         400000      
UDISK       : 428000        218000      
-----------------------------------
no misc partition is found
Hit any key to stop autoboot:  0 
Failed to mount ext2 filesystem...
** Unrecognized filesystem type **
reading /uEnv.txt


177 bytes read
## Warning: defaulting to text format
Failed to mount ext2 filesystem...
** Unrecognized filesystem type **
reading /script.bin


46240 bytes read
Failed to mount ext2 filesystem...
** Unrecognized filesystem type **
reading /uImage


4562648 bytes read
## Booting kernel from Legacy Image at 48000000 ...
   Image Name:   Linux-3.4.79
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4562584 Bytes = 4.4 MiB
   Load Address: 40008000
   Entry Point:  40008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK
Using machid 0x10bb from environment


Starting kernel ...


<6>Booting Linux on physical CPU 0
<6>Initializing cgroup subsys cpuset
<6>Initializing cgroup subsys cpu
<5>Linux version 3.4.79 (matson@ubt) (gcc version 4.6.3 (Ubuntu/Linaro 4.6.3-1ubuntu5) ) #6 SMP PREEMPT Fri Feb 14 23:58:54 CST 2014
CPU: ARMv7 Processor [410fc074] revision 4 (ARMv7), cr=10c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: sun7i
<6>Memory Reserved:
<6>     SYS  : 0x43000000 - 0x4300ffff  (  64 kB)
<6>     G2D  : 0x50000000 - 0x50ffffff  (  16 MB)
<6>     LCD  : 0x51000000 - 0x52ffffff  (  32 MB)
<6>cma: CMA: reserved 192 MiB at 43c00000
Memory policy: ECC disabled, Data cache writealloc
<6>sunxi: Allwinner A20 (AW1651/sun7i) detected.
<7>On node 0 totalpages: 524288
<7>free_area_init_node: node 0, pgdat c08a8880, node_mem_map d3000000
<7>  DMA zone: 512 pages used for memmap
<7>  DMA zone: 0 pages reserved
<7>  DMA zone: 65024 pages, LIFO batch:15
<7>  Normal zone: 1008 pages used for memmap
<7>  Normal zone: 128016 pages, LIFO batch:31
<7>  HighMem zone: 2576 pages used for memmap
<7>  HighMem zone: 327152 pages, LIFO batch:31
<6>PERCPU: Embedded 7 pages/cpu @d400e000 s7040 r8192 d13440 u32768
<7>pcpu-alloc: s7040 r8192 d13440 u32768 alloc=8*4096<c>
<7>pcpu-alloc: <c>[0] <c>0 <c>[0] <c>1 <c>
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 520192
<5>Kernel command line: console=tty0 root=/dev/nandb loglevel=8 console=ttyS0,115200 hdmi.audio=EDID:0 disp.screen0_output_mode=EDID:1280x720p50 rootwait panic=10 rootfstype=ext4 rootflags=discard
<6>PID hash table entries: 4096 (order: 2, 16384 bytes)
<6>Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
<6>Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
<6>allocated 4194304 bytes of page_cgroup
<6>please try 'cgroup_disable=memory' option if you don't want memory cgroups
<6>Memory: 2048MB = 2048MB total
<5>Memory: 1818848k/1818848k available, 278304k reserved, 1318912K highmem
<5>Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    vmalloc : 0xf0000000 - 0xff000000   ( 240 MB)
    lowmem  : 0xc0000000 - 0xef800000   ( 760 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    modules : 0xbf000000 - 0xbfe00000   (  14 MB)
      .text : 0xc0008000 - 0xc080a000   (8200 kB)
      .init : 0xc080a000 - 0xc0842b80   ( 227 kB)
      .data : 0xc0844000 - 0xc08af668   ( 430 kB)
       .bss : 0xc08af68c - 0xc0a6d838   (1785 kB)
<6>SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
<6>Preemptible hierarchical RCU implementation.
<6>     RCU dyntick-idle grace-period acceleration is enabled.
<6>     Additional per-CPU info printed with stalls.
<6>NR_IRQS:192
<6>Architected local timer running at 24.00MHz.
<6>sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
<2>start_kernel(): bug: interrupts were enabled early
<6>Console: colour dummy device 80x30
<6>console [tty0] enabled
<6>Calibrating delay loop... <c>1816.98 BogoMIPS (lpj=9084928)
<6>pid_max: default: 32768 minimum: 301
<6>Mount-cache hash table entries: 512
<6>Initializing cgroup subsys cpuacct
<6>Initializing cgroup subsys memory
<6>Initializing cgroup subsys devices
<6>Initializing cgroup subsys freezer
<6>Initializing cgroup subsys blkio
<6>Initializing cgroup subsys perf_event
<6>CPU: Testing write buffer coherency: ok
<6>CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
<6>hw perfevents: enabled with ARMv7 Cortex-A7 PMU driver, 5 counters available
<6>Setting up static identity map for 0x405c4ae8 - 0x405c4b40
CPU1: Booted secondary processor
<6>CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
<6>Brought up 2 CPUs
<6>SMP: Total of 2 processors activated (3640.52 BogoMIPS).
<6>devtmpfs: initialized
<6>dummy: 
<6>NET: Registered protocol family 16
<6>DMA: preallocated 256 KiB pool for atomic coherent allocations
<6>hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
<6>hw-breakpoint: maximum watchpoint size is 8 bytes.
<6>[ccu-inf] aw clock manager init
<6>[ccu-inf] aw_ccu_init
<6>[ccu-inf] script config pll3 to 297MHz
<6>[ccu-inf] script config pll4 to 300MHz
<6>[ccu-inf] script config pll6 to 600MHz
<6>[ccu-inf] script config pll7 to 297MHz
<6>[ccu-inf] script config pll8 to 336MHz
<6>Init eGon pin module V2.0
<6>bio: create slab <bio-0> at 0
<6>sunxi_gpio driver init ver 1.3
<6>gpiochip_add: registered GPIOs 1 to 2 on device: A1X_GPIO
<5>SCSI subsystem initialized
<7>libata version 3.00 loaded.
<6>usbcore: registered new interface driver usbfs
<6>usbcore: registered new interface driver hub
<6>usbcore: registered new device driver usb
<6>Linux media interface: v0.10
<6>Linux video capture interface: v2.00
<6>Advanced Linux Sound Architecture Driver Version 1.0.25.
<6>cfg80211: Calling CRDA to update world regulatory domain
<6>Switching to clocksource arch_sys_counter
<5>FS-Cache: Loaded
<6>CacheFiles: Loaded
<6>sw_hcd_host0 sw_hcd_host0: sw_hcd host driver
<6>sw_hcd_host0 sw_hcd_host0: new USB bus registered, assigned bus number 1
<6>hub 1-0:1.0: USB hub found
<6>hub 1-0:1.0: 1 port detected
config i2c gpio with gpio_config api 
<6>I2C: i2c-0: AW16XX I2C adapter
<6>NET: Registered protocol family 2
<6>IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
<6>TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
<6>TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
<6>TCP: Hash tables configured (established 131072 bind 65536)
<6>TCP: reno registered
<6>UDP hash table entries: 512 (order: 2, 16384 bytes)
<6>UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
<6>NET: Registered protocol family 1
<6>RPC: Registered named UNIX socket transport module.
<6>RPC: Registered udp transport module.
<6>RPC: Registered tcp transport module.
<6>RPC: Registered tcp NFSv4.1 backchannel transport module.
pm: select wifi: ap6210
<6>ap6xxx: config 32k clock
[wifi_pm]: wifi gpio init is OK !!
[rfkill]: rfkill set power 0
<6>audit: initializing netlink socket (disabled)
<5>type=2000 audit(0.580:1): initialized
highmem bounce pool size: 64 pages
<5>VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
<5>NFS: Registering the id_resolver key type
<6>NTFS driver 2.1.30 [Flags: R/W].
<6>fuse init (API version 7.18)
<6>msgmni has been set to 1360
<3>alg: comp: Compression test 1 failed for lzo-generic: output len = 57
<6>alg: No test for stdrng (krng)
<6>Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
<6>io scheduler noop registered
<6>io scheduler deadline registered
<6>io scheduler cfq registered (default)
<6>sunxi disp driver loaded (/dev/disp api 1.0)
<6>Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled
<6>[uart]: used uart info.: 0x05
<6>[uart]: serial probe 0 irq 33 mapbase 0x01c28000
<6>sunxi-uart.0: ttyS0 at MMIO 0x1c28000 (irq = 33) is a U6_16550A
[    0.000000] Booting Linux on physical CPU 0
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 3.4.79 (matson@ubt) (gcc version 4.6.3 (Ubuntu/Linaro 4.6.3-1ubuntu5) ) #6 SMP PREEMPT Fri Feb 14 23:58:54 CST 2014
[    0.000000] CPU: ARMv7 Processor [410fc074] revision 4 (ARMv7), cr=10c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine: sun7i
[    0.000000] Memory Reserved:
[    0.000000]  SYS  : 0x43000000 - 0x4300ffff  (  64 kB)
[    0.000000]  G2D  : 0x50000000 - 0x50ffffff  (  16 MB)
[    0.000000]  LCD  : 0x51000000 - 0x52ffffff  (  32 MB)
[    0.000000] cma: CMA: reserved 192 MiB at 43c00000
[    0.000000] Memory policy: ECC disabled, Data cache writealloc
[    0.000000] sunxi: Allwinner A20 (AW1651/sun7i) detected.
[    0.000000] On node 0 totalpages: 524288
[    0.000000] free_area_init_node: node 0, pgdat c08a8880, node_mem_map d3000000
[    0.000000]   DMA zone: 512 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 65024 pages, LIFO batch:15
[    0.000000]   Normal zone: 1008 pages used for memmap
[    0.000000]   Normal zone: 128016 pages, LIFO batch:31
[    0.000000]   HighMem zone: 2576 pages used for memmap
[    0.000000]   HighMem zone: 327152 pages, LIFO batch:31
[    0.000000] PERCPU: Embedded 7 pages/cpu @d400e000 s7040 r8192 d13440 u32768
[    0.000000] pcpu-alloc: s7040 r8192 d13440 u32768 alloc=8*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 520192
[    0.000000] Kernel command line: console=tty0 root=/dev/nandb loglevel=8 console=ttyS0,115200 hdmi.audio=EDID:0 disp.screen0_output_mode=EDID:1280x720p50 rootwait panic=10 rootfstype=ext4 rootflags=discard
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] allocated 4194304 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.000000] Memory: 2048MB = 2048MB total
[    0.000000] Memory: 1818848k/1818848k available, 278304k reserved, 1318912K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xf0000000 - 0xff000000   ( 240 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xef800000   ( 760 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc080a000   (8200 kB)
[    0.000000]       .init : 0xc080a000 - 0xc0842b80   ( 227 kB)
[    0.000000]       .data : 0xc0844000 - 0xc08af668   ( 430 kB)
[    0.000000]        .bss : 0xc08af68c - 0xc0a6d838   (1785 kB)
[    0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  RCU dyntick-idle grace-period acceleration is enabled.
[    0.000000]  Additional per-CPU info printed with stalls.
[    0.000000] NR_IRQS:192
[    0.000000] Architected local timer running at 24.00MHz.
[    0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
[    0.000000] start_kernel(): bug: interrupts were enabled early
[    0.000000] Console: colour dummy device 80x30
[    0.000000] console [tty0] enabled
[    0.014073] Calibrating delay loop... 1816.98 BogoMIPS (lpj=9084928)
[    0.076018] pid_max: default: 32768 minimum: 301
[    0.079732] Mount-cache hash table entries: 512
[    0.084084] Initializing cgroup subsys cpuacct
[    0.087433] Initializing cgroup subsys memory
[    0.090875] Initializing cgroup subsys devices
[    0.094330] Initializing cgroup subsys freezer
[    0.097570] Initializing cgroup subsys blkio
[    0.101261] Initializing cgroup subsys perf_event
[    0.104862] CPU: Testing write buffer coherency: ok
[    0.110108] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.117244] hw perfevents: enabled with ARMv7 Cortex-A7 PMU driver, 5 counters available
[    0.122811] Setting up static identity map for 0x405c4ae8 - 0x405c4b40
[    0.238787] CPU1: Booted secondary processor
[    0.297758] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.299774] Brought up 2 CPUs
[    0.305137] SMP: Total of 2 processors activated (3640.52 BogoMIPS).
[    0.308533] devtmpfs: initialized
[    0.316028] dummy: 
[    0.326741] NET: Registered protocol family 16
[    0.356070] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.364111] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.368940] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.372141] [ccu-inf] aw clock manager init
[    0.374430] [ccu-inf] aw_ccu_init
[    0.378417] [ccu-inf] script config pll3 to 297MHz
[    0.382187] [ccu-inf] script config pll4 to 300MHz
[    0.385973] [ccu-inf] script config pll6 to 600MHz
[    0.389739] [ccu-inf] script config pll7 to 297MHz
[    0.393504] [ccu-inf] script config pll8 to 336MHz
[    0.396321] Init eGon pin module V2.0
[    0.405797] bio: create slab <bio-0> at 0
[    0.409424] sunxi_gpio driver init ver 1.3
[    0.415155] gpiochip_add: registered GPIOs 1 to 2 on device: A1X_GPIO
[    0.418371] SCSI subsystem initialized
[    0.421302] libata version 3.00 loaded.
[    0.426008] usbcore: registered new interface driver usbfs
[    0.430388] usbcore: registered new interface driver hub
[    0.434618] usbcore: registered new device driver usb
[    0.437772] Linux media interface: v0.10
[    0.441423] Linux video capture interface: v2.00
[    0.447104] Advanced Linux Sound Architecture Driver Version 1.0.25.
[    0.453304] cfg80211: Calling CRDA to update world regulatory domain
[    0.457992] Switching to clocksource arch_sys_counter
[    0.460159] FS-Cache: Loaded
[    0.462384] CacheFiles: Loaded
[    0.498375] sw_hcd_host0 sw_hcd_host0: sw_hcd host driver
[    0.505146] sw_hcd_host0 sw_hcd_host0: new USB bus registered, assigned bus number 1
[    0.508726] hub 1-0:1.0: USB hub found
[    0.511690] hub 1-0:1.0: 1 port detected
[    0.516141] config i2c gpio with gpio_config api 
[    0.519390] I2C: i2c-0: AW16XX I2C adapter
[    0.523492] NET: Registered protocol family 2
[    0.529896] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.536979] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.544571] TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
[    0.551190] TCP: Hash tables configured (established 131072 bind 65536)
[    0.553424] TCP: reno registered
[    0.558317] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.563686] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.567362] NET: Registered protocol family 1
[    0.572801] RPC: Registered named UNIX socket transport module.
[    0.576539] RPC: Registered udp transport module.
[    0.580204] RPC: Registered tcp transport module.
[    0.585626] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.588424] pm: select wifi: ap6210
[    0.591214] ap6xxx: config 32k clock
[    0.594444] [wifi_pm]: wifi gpio init is OK !!
[    0.597513] [rfkill]: rfkill set power 0
[    0.602707] audit: initializing netlink socket (disabled)
[    0.606439] type=2000 audit(0.580:1): initialized
[    0.610820] highmem bounce pool size: 64 pages
[    0.624206] VFS: Disk quotas dquot_6.5.2
[    0.629745] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.637080] NFS: Registering the id_resolver key type
[    0.642046] NTFS driver 2.1.30 [Flags: R/W].
[    0.645465] fuse init (API version 7.18)
[    0.649021] msgmni has been set to 1360
[    0.660689] alg: comp: Compression test 1 failed for lzo-generic: output len = 57
[    0.664081] alg: No test for stdrng (krng)
[    0.670826] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    0.673798] io scheduler noop registered
[    0.677042] io scheduler deadline registered
[    0.680751] io scheduler cfq registered (default)
[    0.685729] sunxi disp driver loaded (/dev/disp api 1.0)
[    0.691313] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled
[    0.696227] [uart]: used uart info.: 0x05
[    0.700967] [uart]: serial probe 0 irq 33 mapbase 0x01c28000
[    0.727474] sunxi-uart.0: ttyS0 at MMIO 0x1c28000 (irq = 33) is a U6_16550A
<6>console [ttyS0] enabled
[    1.495647] console [ttyS0] enabled
<6>[uart]: serial probe 2 irq 35 mapbase 0x01c28800
[    1.504090] [uart]: serial probe 2 irq 35 mapbase 0x01c28800
<6>sunxi-uart.2: ttyS1 at MMIO 0x1c28800 (irq = 35) is a U6_16550A
[    1.536115] sunxi-uart.2: ttyS1 at MMIO 0x1c28800 (irq = 35) is a U6_16550A
<7>G2D: drv_g2d_init
[    1.545805] G2D: drv_g2d_init
<6>G2D: g2dmem: g2d_start=50000000, g2d_size=1000000
[    1.553524] G2D: g2dmem: g2d_start=50000000, g2d_size=1000000
<6>G2D: head:d0000000,tail:d1000000
[    1.562517] G2D: head:d0000000,tail:d1000000
<6>G2D: Module initialized.major:250
[    1.570137] G2D: Module initialized.major:250
<6>brd: module loaded
[    1.577715] brd: module loaded
<6>loop: module loaded
[    1.587305] loop: module loaded
[NAND] nand driver version: 0x2 0x9 
[    1.593871] [NAND] nand driver version: 0x2 0x9